The sound signals amplified by the navigation ECU sub-assembly are sent to the speakers from the navigation ECU sub-assembly via the speaker circuit.
If there is a short in a speaker circuit, the navigation ECU sub-assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the navigation ECU sub-assembly or speakers.
*1: for Front Speaker Area
*2: for Rear Speaker Area
*3: for LH Side
*4: for RH Side
Disconnect the G137*1 and/or G138*2 navigation ECU sub-assembly connector.
Disconnect the H3*3 and/or H1*4 front No. 2 speaker assembly connector.
Disconnect the L2*3 and/or K2*4 rear speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G137-1 (FR+) - H1-4 (TWR+) | Always | Below 1 Ω |
| G137-5 (FR-) - H1-2 (TWR-) | Always | Below 1 Ω |
| G137-2 (FL+) - H3-4 (TWL+) | Always | Below 1 Ω |
| G137-6 (FL-) - H3-2 (TWL-) | Always | Below 1 Ω |
| G138-1 (RR+) - K2-1 | Always | Below 1 Ω |
| G138-3 (RR-) - K2-2 | Always | Below 1 Ω |
| G138-2 (RL+) - L2-1 | Always | Below 1 Ω |
| G138-6 (RL-) - L2-2 | Always | Below 1 Ω |
| G137-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| G137-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| G137-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| G137-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| G138-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| G138-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| G138-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| G138-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the malfunction disappears when a known good speaker is installed.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both LH and RH sides.
Proceed to the next step based on the inspection result.
| Proceed to |
|---|
| Malfunction disappears |
| Malfunction does not disappear |
Malfunction disappears
Malfunction does not disappear
*1: for LH Side
*2: for RH Side
Disconnect the H3*1 and/or H1*2 front No. 2 speaker assembly connector.
Disconnect the J1*1 and/or I1*2 front No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H3-3 (+) - J1-1 | Always | Below 1 Ω |
| H3-1 (-) - J1-2 | Always | Below 1 Ω |
| H1-3 (+) - I1-1 | Always | Below 1 Ω |
| H1-1 (-) - I1-2 | Always | Below 1 Ω |
| H3-3 (+) - Body ground | Always | 10 kΩ or higher |
| H3-1 (-) - Body ground | Always | 10 kΩ or higher |
| H1-3 (+) - Body ground | Always | 10 kΩ or higher |
| H1-1 (-) - Body ground | Always | 10 kΩ or higher |
| J1-1 - Body ground | Always | 10 kΩ or higher |
| J1-2 - Body ground | Always | 10 kΩ or higher |
| I1-1 - Body ground | Always | 10 kΩ or higher |
| I1-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the front No. 1 speaker assembly connector.
Inspect the front No. 1 speaker assembly connector.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the rear speaker assembly connector.
Inspect the rear speaker assembly connector.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG