The navigation ECU sub-assembly a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2 to use for adjusting the vehicle position on the display.
*1: except Manual Transaxle
*2: for Manual Transaxle
Enter the "Function Check/Setting I" mode and select "Vehicle Signal".
Check that the display changes between ON and OFF according to the shift lever position.
| Shift Lever Position | Display |
|---|---|
| R | ON |
| Except R | OFF |
This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Navigation ECU Sub-assembly) |
Disconnect the navigation ECU sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G139-2 (REV) - Body ground | Ignition switch ON, shift lever in R | 11 to 14 V |
| G139-2 (REV) - Body ground | Ignition switch ON, shift lever any position other than in R | Below 1 V |
| Proceed to |
|---|
| OK |
| NG (except Manual Transaxle) |
| NG (for Manual Transaxle) |
OK
NG (except Manual Transaxle)
NG (for Manual Transaxle)
Disconnect the G139 navigation ECU sub-assembly connector.
Disconnect the B36 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G139-2 (REV) - B36-2 (RL) | Always | Below 1 Ω |
| G139-2 (REV) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch Assembly) |
Disconnect the park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B36-1 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for K111F:
Click hereDrivetrain>K111F MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for U660F:
Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for U760E:
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for U760F:
NG
Disconnect the G139 navigation ECU sub-assembly connector.
Disconnect the B35 back-up light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G139-2 (REV) - B35-1 | Always | Below 1 Ω |
| G139-2 (REV) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Back-up Light Switch Assembly) |
Disconnect the back-up light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B35-2 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for EA64:
Click hereDrivetrain>EA64 MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>REMOVAL
for EA64F:
Click hereDrivetrain>EA64F MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>REMOVAL
for EB61F:
Click hereDrivetrain>EB61F MANUAL TRANSMISSION / TRANSAXLE>BACK-UP LIGHT SWITCH>REMOVAL
NG