Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Downhill Assist Control Indicator Light does not Come ON  


DESCRIPTION

Even if the downhill assist control switch is pressed, the downhill assist control indicator light blinks and downhill assist control does not activate under the following conditions:

·

Gear position is not R.

·

The brake system is malfunctioning.

·

The vehicle speed is 25 km/h (15 mph) or more.


WIRING DIAGRAM

C279159E05
3.385,2.573 3.844,2.771 0.458,0.198 10 false G29 3.396,2.74 4.385,3.313 0.99,0.573 10 false Downhill Assist Control Switch 3.24,2.167 3.427,2.417 0.188,0.25 10 false 1 4.198,2.167 4.396,2.406 0.198,0.24 10 false 4 5.406,2.167 5.719,2.365 0.313,0.198 10 false 29 5.656,2.26 6.115,2.458 0.458,0.198 10 false HDCS 5.51,2.823 5.969,3.021 0.458,0.198 10 false A64 5.51,3 7.115,3.531 1.604,0.531 10 false Skid Control ECU (Brake Actuator Assembly) 1.75,0.573 2.323,0.833 0.573,0.26 10 false CAN I/F 0.906,1.042 1.365,1.24 0.458,0.198 10 false CPU 1.063,2.948 2.229,3.24 1.167,0.292 10 false Downhill Assist 1.771,3.438 2.052,3.698 0.281,0.26 10 false IG 0.594,3.958 2.521,4.281 1.927,0.323 10 false Combination Meter Assembly 0.979,4.406 2.99,4.708 2.01,0.302 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD)
DTC is output (for RHD)



DTC is not output

2.CHECK HARNESS AND CONNECTOR (HDCS TERMINAL)

DTC is output (for LHD)

DTC is output (for RHD)

2.CHECK HARNESS AND CONNECTOR (HDCS TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


c.
C199357C59
1.625,0.083 2,0.333 0.375,0.25 1.656,1.844 1.729,1.396 false 0,0 0.313,0.156 0.313,0.156 10 false *a 1.688,0.125 2.146,0.323 0.458,0.198 10 false A64 1.479,1.875 1.958,2.073 0.479,0.198 10 false HDCS
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A64-29 (HDCS) - Body ground Downhill assist control switch is pushed Below 1 Ω
A64-29 (HDCS) - Body ground Downhill assist control switch is not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (DOWNHILL ASSIST CONTROL LIGHT)

NG

5.INSPECT DOWNHILL ASSIST CONTROL SWITCH
3.PERFORM ACTIVE TEST USING GTS (DOWNHILL ASSIST CONTROL LIGHT)
a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, perform the Active Test.


Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light Indicator light OFF/ON Observe combination meter
Vehicle condition: Vehicle stopped
g.

When performing the ABS Warning Light Active Test, check Downhill assist control indicator light in the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light ON or OFF OFF: Downhill assist control indicator light off
ON: Downhill assist control indicator light on
w/ Downhill Assist Control:
The item is displayed on the GTS but not used.
OFF: Always
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Downhill Assist Control Light
Data List Display
Downhill Assist Control Light
50004 105 66 59
Result:
Result Proceed to
Downhill assist control indicator light in the Data List does not change using the Active Test A
Downhill assist control indicator light in the Data List turns ON/OFF using the Active Test B



A

B

4.INSPECT COMBINATION METER ASSEMBLY
4.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform Active Test of the combination meter assembly using the GTS.


Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Downhill Assist Control
50004 122 49
c.

Check the combination meter assembly.


OK:

The Downhill assist control indicator light turns on or off in accordance with the GTS.


Result:
Proceed to
OK
NG



OK

NG

5.INSPECT DOWNHILL ASSIST CONTROL SWITCH
a.

Turn the ignition switch off.


b.

c.

Result:
Result
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-29 (HDCS) - G29-4 Always Below 1 Ω
A64-29 (HDCS) or G29-4 - Body ground Always 10 kΩ or higher
G29-1 - Body ground Always Below 1 Ω


Result:
Result
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR