Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM › 2012.12–2015.10
RM3090E _53 Suspension _008764 FRONT SUSPENSION _0049354 FRONT LOWER SUSPENSION ARM A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48069 1.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.



Hide 51201 2.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

NOTICE:
·

Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.

·

Use the attachments to keep the front suspension crossmember sub-assembly level.

·

The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.




b.

Tighten the 2 bolts on the left and right sides while alternately inserting SST into the left and right side reference holes in the front suspension crossmember sub-assembly.

C234336C03
3.469,0.115 3.781,0.271 0.313,0.156 10 *a 1.333,5.583 1.646,5.74 0.313,0.156 10 *b 2.229,5.573 2.542,5.729 0.313,0.156 10 *c 4.781,5.563 5.094,5.719 0.313,0.156 10 *b 5.646,5.573 5.958,5.729 0.313,0.156 10 *c
*a Front of the Vehicle *b OK
*c NG - -


SST
09670-00020  

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


c.

Lower the engine lifter.


d.

Install the rear engine mounting insulator with bolts A and B, and nuts C and D by tightening them in several steps.

C279628N01
3.24,1.802 3.396,2 0.156,0.198 10 A 4.49,1.813 4.646,2.01 0.156,0.198 10 B 3.26,2.333 3.417,2.531 0.156,0.198 10 C 4.552,2.615 4.708,2.813 0.156,0.198 10 D

Torque:
Bolt A, B, Nut C, D : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Temporarily tighten bolt A, and then fully tighten the 2 bolts and 2 nuts in the order of B, D, C, and A.



Hide 52258B 3.INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH

a.
C149508N04
1.49,0.531 1.646,0.729 0.156,0.198 10 A 2.594,0.833 2.75,1.031 0.156,0.198 10 B 0.854,1.802 1.01,2 0.156,0.198 10 C

Install the front suspension member rear brace LH with the 3 bolts.

Torque:
Bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
Bolt B, C : 93 N*m (948 kgf*cm, 69 ft.*lbf)

NOTICE:

Temporarily tighten bolts A and B, and then fully tighten the 3 bolts in the order of C, B, and A.



Hide 52257A 4.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 51425B 5.INSTALL ENGINE FRONT MOUNTING BRACKET REINFORCEMENT LOWER (for 1AD and 3ZR 2WD)

a.
A295897

Install the engine front mounting bracket reinforcement lower with the 2 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 51218A 6.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
A296303

Install the front suspension member reinforcement LH with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 51217A 7.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.
A296302

Install the front suspension member reinforcement RH with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 48069 8.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Connect the front lower No. 1 suspension arm sub-assembly to the lower arm ball joint with the bolt and 2 nuts.

Torque:
92 N*m (938 kgf*cm, 68 ft.*lbf)


Hide 48068 9.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45047 10.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 11.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 12.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.
C279180

Connect the front stabilizer link assembly LH to the front stabilizer bar with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.



Hide 48820B 13.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45025D 14.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 15.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 16.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 51444A 17.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH with the 3 clips.


Hide 51443C 18.INSTALL REAR ENGINE UNDER COVER RH

a.

Install the rear engine under cover RH with the 3 clips.


Hide 19.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 20. STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Bounce the vehicle up and down at the corners several times to stabilizer the suspension.


Hide 48069 21.TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C279176C01
1.427,0.479 1.521,0.177 false 1.531,0.177 1.979,0.177 false 2.229,1.292 2.542,1.448 0.313,0.156 10 *a 2.115,3 2.427,3.156 0.313,0.156 10 *b 2.094,0.125 2.552,0.323 0.458,0.198 10 SST 0.979,0.25 1.135,0.448 0.156,0.198 10 A 1.042,1.917 1.198,2.115 0.156,0.198 10 B
*a Fulcrum Length
*b Turn


Using SST, tighten bolt A.

SST
09961-01270  

Torque:
without SST : 233 N*m (2376 kgf*cm, 172 ft.*lbf)
with SST : 172 N*m (1754 kgf*cm, 127 ft.*lbf)

NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.

·

Use a torque wrench with a fulcrum length of 425 mm (1.39 ft.).

·

The torque value for use with SST is effective when SST is parallel to the torque wrench.

·

The final torque must be applied under standard vehicle height conditions.




b.

Tighten bolt B.

Torque:
214 N*m (2182 kgf*cm, 158 ft.*lbf)


Hide 24.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT