Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2012.12–2014.10
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046815 ENGINE ASSEMBLY A

3ZR-FAE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.


NOTICE:

for Manual Transaxle:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


HINT:

Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly, camshaft housing sub-assembly, camshaft timing gear assembly, camshaft timing exhaust gear assembly, piston sub-assembly or piston ring.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A298938N01
1.333,0.469 1.51,0.688 0.177,0.219 11 1 2.396,1.802 2.573,2.021 0.177,0.219 11 2 1.094,1.719 1.271,1.938 0.177,0.219 11 3 2.688,0.604 2.865,0.823 0.177,0.219 11 4

Temporarily install the engine mounting insulator LH with the 4 bolts.


b.

Tighten the 4 bolts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.

Install the wire harness clamp bracket with the bolt.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


Hide 12305 2.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A297257N01
2.771,1.135 2.927,1.333 0.156,0.198 10 1 0.969,0.302 1.125,0.5 0.156,0.198 10 2 0.677,1.896 0.833,2.094 0.156,0.198 10 3

Temporarily install the engine mounting insulator sub-assembly RH with the 3 bolts.


b.

Tighten the 3 bolts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.

Install the radiator reservoir bracket with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 12371A 3.INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A297245C02
0.969,1.302 1.125,1.5 0.156,0.198 10 1 1.479,1.479 1.635,1.677 0.156,0.198 10 4 2.167,1.49 2.323,1.688 0.156,0.198 10 3 2.563,1.208 2.719,1.406 0.156,0.198 10 2 0.979,2.771 1.135,2.969 0.156,0.198 10 1 1.479,2.948 1.635,3.146 0.156,0.198 10 4 2.156,2.99 2.313,3.188 0.156,0.198 10 3 2.563,2.677 2.719,2.875 0.156,0.198 10 2 0.333,0.302 0.646,0.458 0.313,0.156 10 *A 0.323,1.76 0.635,1.917 0.313,0.156 10 *B
*A for Manual Transaxle
*B for CVT


Temporarily install the rear engine mounting insulator with the 2 bolts and 2 nuts.


b.

Tighten the 2 bolts and 2 nuts in the sequence shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 43457 4.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 6.REMOVE ENGINE FROM ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Attach a sling device and hang the engine with a chain block.


b.

Lift the engine and remove it from the engine stand.


Hide 82121 8.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine.


Hide 13405 9.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

Hide 31400 10.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle)

Hide 31407B 11.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)

Hide 12.INSPECT CLUTCH PIPE LINE (for Manual Transaxle)

Hide 31407B 13.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)

Hide 14.INSTALL CLUTCH TUBE (for Manual Transaxle)

Hide 31250 15.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 31210 16.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31210 17.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 32101 18.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

Hide 30300 19.INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

Hide 30400 20.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Hide 36100 21.INSTALL TRANSFER ASSEMBLY

Hide 11363A 22.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 28100 23.INSTALL STARTER ASSEMBLY

Hide 45319A 24.INSTALL STEERING GEAR HEAT INSULATOR (for RHD)

Hide 25.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Temporarily install the front engine mounting insulator with the through bolt and nut.


b.
A300878C01
1.594,3.396 2.542,3.188 2.542,3.188 1.635,3.188 true 1.031,2.708 1.208,2.708 1.208,2.708 1.49,3.26 true 0.823,2.635 1.01,2.813 0.188,0.177 10 false *2 2.594,3.104 2.781,3.281 0.188,0.177 10 false *1
*1 Alignment Mark
*2 Protrusion


Temporarily install the front suspension crossmember with the through bolt.

HINT:

When installing the suspension crossmember, align the protrusion of the engine mounting bracket with the alignment mark of the engine mounting insulator.



c.

Place the engine on an engine lifter.

HINT:

Place the engine on wooden blocks or equivalent so that the engine is level.



d.

Operate the engine lifter and install the engine to the vehicle.

CAUTION:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While raising the engine into the vehicle, do not allow it to contact the vehicle.




e.

Temporarily install the front suspension crossmember sub-assembly with 2 bolts.


f.

Temporarily install the front suspension member rear brace RH and LH with the 6 bolts.


g.

Install the engine mounting insulator LH with the through bolt and nut.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)

NOTICE:

While holding the bolt in place, tighten the nut.



h.
A297247N01
0.99,0.781 1.146,0.979 0.156,0.198 10 A 1.219,1.615 1.375,1.813 0.156,0.198 10 B

Install the engine mounting insulator sub-assembly RH with the bolt and 2 nuts.

Torque:
for bolt and nut A : 95 N*m (969 kgf*cm, 70 ft.*lbf)
for nut B : 52 N*m (530 kgf*cm, 38 ft.*lbf)


i.

Tighten the 2 front suspension crossmember bolts.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


j.
A297248N01
0.781,0.792 0.938,0.99 0.156,0.198 10 A 0.208,1.885 0.365,2.083 0.156,0.198 10 B 2.542,0.792 2.698,0.99 0.156,0.198 10 A 1.396,1.885 1.552,2.083 0.156,0.198 10 B 1.813,1.885 1.969,2.083 0.156,0.198 10 B 3.219,1.885 3.375,2.083 0.156,0.198 10 B

Tighten the 6 front suspension member rear brace bolts.

Torque:
for bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
for bolt B : 93 N*m (948 kgf*cm, 69 ft.*lbf)


k.

Remove the 2 bolts and No. 1 and No. 2 engine hangers.


l.

Install the air fuel ratio sensor bracket with the bolt. Then connect the air fuel ratio sensor connector.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


m.

Attach the fuel tube clamp.


n.
A297249N01
0.156,0.365 0.313,0.563 0.156,0.198 10 A 0.594,0.354 0.75,0.552 0.156,0.198 10 A 1.573,1.563 1.729,1.76 0.156,0.198 10 B 1.917,0.531 2.073,0.729 0.156,0.198 10 B 2.75,0.354 2.906,0.552 0.156,0.198 10 A 3.198,0.354 3.354,0.552 0.156,0.198 10 A

Install the front crossmember sub-assembly with the 6 bolts.

Torque:
for bolt A : 99 N*m (1010 kgf*cm, 73 ft.*lbf)
for bolt B : 95 N*m (969 kgf*cm, 70 ft.*lbf)


o.

Tighten the rear engine mounting insulator bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

HINT:

Check that the protrusion of the engine mounting bracket is aligned with the alignment mark of the engine mounting insulator.



p.

Tighten the front engine mounting insulator bolt and nut.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)

NOTICE:

While holding the bolt in place, tighten the nut.



Hide 51218A 26.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.

Install the front suspension member reinforcement LH with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 51217A 27.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.

Install the front suspension member reinforcement RH with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 32101A 28.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT)

Hide 37100 29.TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 37100 30.TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 89465 31.CONNECT HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 17410 32.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 43420G 33.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 48069 36.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 37.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45047 38.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 39.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 40.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 41.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 42.CONNECT FRONT SPEED SENSOR LH

Hide 43.CONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 44.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 45.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 45025D 46.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 47.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 48.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 31418 49.CONNECT CLUTCH HOSE (for Manual Transaxle)

a.

Connect the clutch hose and install the clip to the clutch hose.

NOTICE:

Install the clip as far as it will go.



b.

Using a 10 mm union nut wrench, connect the clutch hose to the accumulator to flexible hose tube while holding the clutch hose.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Do not kink or damage the clutch hose.

·

Do not allow any foreign matter such as dirt or dust to enter the clutch hose from the clip or bracket.

·

This torque value is effective when the union nut wrench is parallel to the torque wrench.




Hide 33820B 50.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)

a.

Connect the clamp of the transmission control cable assembly with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the transmission control cable assembly to the transmission control cable support.


c.

Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.


d.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33820B 51.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

a.

Connect the control cable to the control cable bracket, and install 2 new clips.


b.

Connect the control cable to the transaxle, and install the 2 washers and 2 clips.


Hide 52.CONNECT WIRE HARNESS AND HOSE

a.

Connect the heater water outlet hose and heater water inlet hose to the heater core and slide the 2 clamps to secure the hoses.


b.

Connect the connector tube hose to the air tube and slide the clamp to secure the hose.


c.

for Manual Transaxle:

Attach the clamp and connect the engine wire to the manual transaxle with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


d.

for CVT:

Attach the clamp and connect the engine wire to the CVT with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


e.

Connect the starter wire to terminal B with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


f.

Attach the wire harness clamp and connect the terminal cap.


g.

Connect the wire harness and attach the 2 wire harness claws.


h.

Connect the 2 engine room junction block connectors and install the nut.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


i.

Install the bolt and attach the 2 wire harness clamps.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 23901 53.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>PRECAUTION


Hide 16571C 54.CONNECT NO. 1 RADIATOR HOSE

a.

for CVT:

Connect the breather plug hose to the clamp.


b.

Connect the No. 1 radiator hose to the cylinder head sub-assembly, and slide the hose clamp to secure the hose.


Hide 74414B 56.INSTALL BATTERY BRACKET REINFORCEMENT

Hide 74411B 57.INSTALL FRONT BATTERY BRACKET

Hide 16057 58.INSTALL RADIATOR HOSE SUB-ASSEMBLY

Hide 74431 59.INSTALL BATTERY TRAY

Hide 28800 60.INSTALL BATTERY

Hide 74404A 61.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 62.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 63.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 88310 64.CONNECT COMPRESSOR ASSEMBLY WITH PULLEY

a.

Using an E8 "TORX" socket wrench, connect the compressor with pulley assembly with the 2 stud bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.
A270913N01
0.333,1.531 0.49,1.729 0.156,0.198 10 1 0.771,1.802 0.927,2 0.156,0.198 10 2 0.354,0.323 0.51,0.521 0.156,0.198 10 3 0.688,0.563 0.844,0.76 0.156,0.198 10 4

Install the 2 bolts and 2 nuts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolts and the nuts in the order shown in the illustration.



c.

Connect the connector and attach the wire harness clamp.


Hide 16572D 65.CONNECT NO. 2 RADIATOR HOSE

Hide 27020 66.INSTALL GENERATOR ASSEMBLY

Hide 16470 69.INSTALL RADIATOR RESERVOIR ASSEMBLY

a.

Install the radiator reservoir assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the No. 1 and No. 2 water by-pass hoses to the radiator reservoir assembly, and slide the 2 hose clamps to secure the No. 1 and No. 2 water by-pass hose.


Hide 70.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 71.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 73.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 76.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 77.INSPECT SHIFT LEVER POSITION (for CVT)

Hide 50819 86.INSTALL FRONT FLOOR COVER

Hide 51443 87.INSTALL REAR ENGINE UNDER COVER RH

a.

Install the rear engine under cover RH with the 3 clips.


Hide 51444 88.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH with the 2 clips.


Hide 51441 89.INSTALL NO. 1 ENGINE UNDER COVER

Hide 11212 90.INSTALL NO. 2 CYLINDER HEAD COVER