48815
1.INSTALL FRONT STABILIZER BAR BUSHING LH
| *a | Stopper |
| *b | Dust Lip |
| *c | Front of the Vehicle |
| *d | Inside of the Vehicle |
Install the front stabilizer bar bushing to the front stabilizer bar as shown in the illustration.
Install the front stabilizer bar bushing so that the dust lips face the outside of the vehicle.
Install the front stabilizer bar bushing so that the cutouts face the rear of the vehicle.
48815
2.INSTALL FRONT STABILIZER BAR BUSHING RH
Use the same procedure described for the LH side.
48811
3.INSTALL FRONT STABILIZER BAR
Install the front stabilizer bar to the front suspension crossmember so that the identification mark is positioned on the right side of the vehicle.
| *a | Identification Mark | *b | Front of the Vehicle |
| *c | Top of the Vehicle | - | - |
52255B
4.INSTALL FRONT SUSPENSION MEMBER BRACE
| *a | Protrusion |
Install the front suspension member brace with the 8 bolts.
After installing the front suspension member brace, mark sure that the protrusions of the front stabilizer bar bushings are visible.
48069
5.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.
51201
6.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.
Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.
Use the attachments to keep the front suspension crossmember sub-assembly level.
The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.
Tighten the bolts on the left and right sides while alternately inserting SST into the left and right side reference holes in the front suspension crossmember sub-assembly.
| *a | Front of the Vehicle | *b | OK |
| *c | NG | - | - |
Lower the engine lifter.
Install the rear engine mounting insulator with bolts A and B, and nuts C and D by tightening them in several steps.
Temporarily tighten bolt A, and then fully tighten the 2 bolts and 2 nuts in the order of B, D, C, and A.
52258B
7.INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH
Install the front suspension member rear brace LH with the 3 bolts.
Temporarily tighten bolts A and B, and then fully tighten the 3 bolts in the order of C, B, and A.
52257A
8.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH
Use the same procedure described for the LH side.
51425B
9.INSTALL ENGINE FRONT MOUNTING BRACKET REINFORCEMENT LOWER (for 1AD and 3ZR 2WD)
Install the engine front mounting bracket reinforcement lower with the 2 bolts.
51218A
10.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH
Install the front suspension member reinforcement LH with the 4 bolts.
51217A
11.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH
Install the front suspension member reinforcement RH with the 4 bolts.
48069
12.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Connect the front lower No. 1 suspension arm sub-assembly to the lower arm ball joint with the bolt and 2 nuts.
48068
13.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
45047
14.CONNECT TIE ROD END SUB-ASSEMBLY LH
45046
15.CONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
48810
16.INSTALL FRONT STABILIZER LINK ASSEMBLY LH
Install the front stabilizer link assembly LH with the 2 nuts.
If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.
48820B
17.INSTALL FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
45025D
18.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45260
19.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
20.INSTALL COLUMN HOLE COVER SILENCER SHEET
51444A
21.INSTALL REAR ENGINE UNDER COVER LH
Install the rear engine under cover LH with the 3 clips.
51443C
22.INSTALL REAR ENGINE UNDER COVER RH
Install the rear engine under cover RH with the 3 clips.
23.INSTALL FRONT WHEELS
24. STABILIZE SUSPENSION
Lower the vehicle.
Bounce the vehicle up and down at the corners several times to stabilizer the suspension.
48069
25.TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
| *a | Fulcrum Length |
| *b | Turn |
Using SST, tighten bolt A.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.
Use a torque wrench with a fulcrum length of 425 mm (1.39 ft.).
The torque value for use with SST is effective when SST is parallel to the torque wrench.
The final torque must be applied under standard vehicle height conditions.
Tighten bolt B.
50819
26.INSTALL FRONT FLOOR COVER
51441
27.INSTALL NO. 1 ENGINE UNDER COVER
for AD Series Engine: Click hereEngine / Hybrid System>1AD-FTV ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
for 2AR-FE and 3ZR-FE: Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
for 3ZR-FAE Engine: Click hereEngine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
28.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT