Home › Suspension › REAR SUSPENSION › REAR LOWER ARM
RM3090E _53 Suspension _008765 REAR SUSPENSION _0049362 REAR LOWER ARM A

REAR SUSPENSION  REAR LOWER ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48740F 1.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Temporarily install the rear No. 2 suspension arm to the suspension member with the bolt and nut.


Hide 48259A 2.INSTALL REAR UPPER COIL SPRING INSULATOR LH

C276119C01
3,0.417 3.26,0.604 0.26,0.188 10 *a
*a 10 mm or less


a.

Install the rear upper coil spring insulator to the rear coil spring.

NOTICE:

Install the rear upper coil insulator so that the distance between the stopper and upper end of the rear coil spring is 10 mm (0.394 in.) or less.



Hide 48258C 3.INSTALL REAR LOWER COIL SPRING INSULATOR LH

a.

Install the rear lower coil spring insulator to the rear No. 2 suspension arm.


Hide 48231B 4.INSTALL REAR COIL SPRING LH

a.
C266194C03
0.199,2.302 0.466,2.527 0.267,0.225 10 *a 1.354,1.775 0.421,2.386 false 0.421,2.386 1.355,3.148 false
*a Identification Mark


Install the rear coil spring to the rear No. 2 suspension arm.

NOTICE:

Install the rear coil spring so that the identification marks are positioned as shown in the illustration.



b.
C267389

Using a jack and wooden block, raise the vehicle gradually to install the rear No. 2 suspension arm to the rear axle carrier. Then temporarily install the bolt.


Hide 48840A 5.INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 48720A 6.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C226957

Temporarily install the rear No. 1 suspension arm to the rear axle carrier with a new nut.


b.
C226958

Insert the rear suspension toe adjust cam sub-assembly from the rear of the vehicle to install the rear No. 1 suspension arm assembly LH, and then temporarily install the No. 2 camber adjust cam with the nut.


Hide 48540 7.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48740F 9.TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

C266199

a.

Tighten the 2 bolts and nut of the rear No. 2 suspension arm assembly.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)

NOTICE:

Since a stopper nut is used, tighten the bolt.



Hide 48540 10.TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48720A 11.TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C226957

Tighten the nut.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


b.
C226958

Tighten the nut of the rear No. 1 suspension arm.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:

Align the matchmarks on the rear suspension member and adjust cam.



Hide 89408C 12.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Automatic Headlight Beam Level Control System)

Hide 13.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 14.INSPECT AND ADJUST REAR WHEEL ALIGNMENT