Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048167 BLOCKING SYSTEM Y

THEFT DETERRENT / KEYLESS ENTRY  BLOCKING SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


DESCRIPTION

HINT:
·

Use this procedure to troubleshoot the blocking system.

·

*: Use the GTS.

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: (desired system). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.

HINT:

A simple method to determine whether the battery is depleted is to operate the horn.



Result:
Proceed to
NEXT



NEXT

3.START ENGINE
3.START ENGINE
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT*

NG

4.CHECK DTC OUTPUT*
a.

Check for DTCs and note any codes that are output.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Immobiliser > Trouble Codes
50001 260
Body Electrical > Telematics > Trouble Codes
50001 233

b.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Body Electrical > Entry&Start > Clear DTCs
50002 125
Body Electrical > Immobiliser > Clear DTCs
50002 260
Body Electrical > Telematics > Clear DTCs
50002 233

Result:
Result Proceed to
DTC is not output. A
SFI system (for 2AR-FE) DTC is output. B
SFI system (for 3ZR-FE) DTC is output. C
Immobiliser system (w/ Entry and Start System) DTC is output. D
Immobiliser system (w/o Entry and Start System) DTC is output. E
Entry and start system (for Start Function) DTC is output. F
Blocking system DTC is output. G



A

5.PERFORM SYMPTOMS TABLE

B

C

D

E

F

G

5.PERFORM SYMPTOMS TABLE

Result:
Proceed to
Fault is not listed in the problem symptoms table.
Fault is listed in the problem symptoms table.



Fault is not listed in the problem symptoms table.

6.OVERALL ANALYSIS AND TROUBLESHOOTING*

Fault is listed in the problem symptoms table.

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

6.OVERALL ANALYSIS AND TROUBLESHOOTING*

Result:
Proceed to
NEXT



NEXT

7.REPAIR OR REPLACE
7.REPAIR OR REPLACE
NOTICE:
·

When replacing the certification ECU (smart key ECU assembly)*1, transponder key ECU assembly*2, telephone transceiver assembly, instrument panel integration antenna assembly or mayday battery, refer to the Service Bulletin.

·

When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.

·

When the mayday battery is replaced, perform the necessary registration procedures for the telephone transceiver. For details, refer to the Service Bulletin.


*1: w/ Entry and Start System

*2: w/o Entry and Start System



Result:
Proceed to
NEXT



NEXT

8.CONFIRMATION TEST
8.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END