Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B2769  Tilt Sensor Signal Circuit Malfunction  


DESCRIPTION

This DTC is stored when one of the following occurs: 1) tilt sensor (yaw rate sensor assembly) power supply malfunction; 2) tilt sensor (yaw rate sensor assembly) open malfunction; or 3) EEPROM malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2769 Tilt Sensor Signal Circuit Malfunction
If one of the following is detected:
·

Tilt sensor (yaw rate sensor assembly) power supply malfunction

·

Tilt sensor (yaw rate sensor assembly) open malfunction

·

EEPROM malfunction


·

Tilt sensor (yaw rate sensor assembly)

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

B312497E01
1.76,0.25 2.594,0.458 0.833,0.208 10 false from Battery 3.51,0.438 5.135,0.615 1.625,0.177 10 false ECU-B NO.1 1.188,1.604 1.344,1.802 0.156,0.198 10 false 1 1.396,1.771 1.844,1.99 0.448,0.219 10 false GND 1.333,2.688 1.781,2.906 0.448,0.219 10 false N16 1.344,2.865 4.021,3.24 2.677,0.375 10 false Tilt Sensor (Yaw Rate Sensor Assembly) 3.5,1.75 3.948,1.969 0.448,0.219 10 false CSIF 3.594,1.219 3.885,1.438 0.292,0.219 10 false +B 3.906,1.146 4.063,1.344 0.156,0.198 10 false 6 3.906,1.635 4.063,1.833 0.156,0.198 10 false 5 5.417,1.625 5.573,1.823 0.156,0.198 10 false 6 5.635,1.76 6.25,1.958 0.615,0.198 10 false GCS 5.583,2.927 6.198,3.125 0.615,0.198 10 false G79 5.604,3.094 6.865,3.729 1.26,0.635 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TILT SENSOR [YAW RATE SENSOR ASSEMBLY] - BATTERY AND BODY GROUND)
a.
B309727C01
1.5,0.292 1.927,0.563 0.427,0.271 2.625,1.833 2.177,1.292 false 0.74,1.781 1.208,1.271 false 0.563,1.823 1.021,2.021 0.458,0.198 10 GND 2.573,1.854 3.031,2.052 0.458,0.198 10 +B 1.594,0.344 2.052,0.542 0.458,0.198 10 N16 0.146,0.156 0.604,0.354 0.458,0.198 10 *a
*a Front view of wire harness connector
(to Tilt Sensor [Yaw Rate Sensor Assembly])


Disconnect the tilt sensor (yaw rate sensor assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N16-6 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N16-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - TILT SENSOR [YAW RATE SENSOR ASSEMBLY])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - TILT SENSOR [YAW RATE SENSOR ASSEMBLY])
a.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the N16 tilt sensor (yaw rate sensor assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G79-6 (GCS) - N16-5 (CSIF) Always Below 1 Ω
G79-6 (GCS) - Body ground Always 10 kΩ or higher
N16-5 (CSIF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK WAVEFORM (TILT SENSOR [YAW RATE SENSOR ASSEMBLY]) (CSIF)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WAVEFORM (TILT SENSOR [YAW RATE SENSOR ASSEMBLY]) (CSIF)
a.

Using an oscilloscope, check the waveform.

B312498C05
3.344,0.104 3.74,0.333 0.396,0.229 4.26,1.042 4.729,0.823 false 1.906,2.854 1.74,2.75 false 2.427,2.865 2.26,2.76 false 1.49,0.177 1.802,0.333 0.313,0.156 10 false *a 1.563,2.646 1.875,2.802 0.313,0.156 10 false *b 2.094,2.646 2.406,2.802 0.313,0.156 10 false *c 3.979,2.625 4.292,2.781 0.313,0.156 10 false *d 4.021,3.177 4.333,3.333 0.313,0.156 10 false *e 2.094,3.25 2.406,3.406 0.313,0.156 10 false *f 2.521,3.229 2.854,3.552 0.333,0.323 10 false *g 2.646,3.594 2.958,3.75 0.313,0.156 10 false *h 1.5,4.104 1.802,4.344 0.302,0.24 10 false *i 4.25,4.125 4.594,4.385 0.344,0.26 10 false *j 3.417,0.135 3.729,0.292 0.313,0.156 10 false G79 4.781,0.719 5.24,0.906 0.458,0.188 10 false GCS 1.104,2.469 1.438,2.792 0.333,0.323 10 false *k 1.104,2.979 1.438,3.302 0.333,0.323 10 false *l
*a Component with harness connected
(Main Body ECU [Multiplex Network Body ECU])
*b CSIF Initial Signal
*c CSIF Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State
*k HI *l LO


Measurement Condition
Tester Connection Content
Tester Connection G79-6 (GCS) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the tilt sensor (yaw rate sensor assembly) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Result Proceed to
NG (Waveform output remains LO) A
NG (There is no initial response and the waveform output remains HI) B
OK (There is an initial response) C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE TILT SENSOR (YAW RATE SENSOR ASSEMBLY)

C