Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is installed together with the hood lock. This switch turns on when the engine hood is closed and turns off when the engine hood is opened.

WIRING DIAGRAM

B341516E01
5.156,2.625 5.667,2.802 0.51,0.177 10 G79 2.271,0.906 2.427,1.104 0.156,0.198 10 2 2.448,0.906 2.604,1.104 0.156,0.198 10 E 2.917,0.906 3.073,1.104 0.156,0.198 10 + 3.115,0.906 3.271,1.104 0.156,0.198 10 1 5.01,0.896 5.167,1.094 0.156,0.198 10 5 5.188,1 6.052,1.177 0.865,0.177 10 HCTY 2.385,1.354 3.063,1.51 0.677,0.156 10 A50*1 2.385,1.49 3.063,1.646 0.677,0.156 10 A59*2 2.375,1.656 3.823,2.188 1.448,0.531 10 Hood Lock Assembly (Engine Hood Courtesy Switch) 5.156,2.771 6.833,3.135 1.677,0.365 10 Main Body ECU (Multiplex Network Body ECU) 0.24,2.99 2.219,3.156 1.979,0.167 10 *1: w/ Stop and Start System 0.25,3.344 2.229,3.51 1.979,0.167 10 *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.


PROCEDURE

1.READ VALUE USING GTS (HOOD COURTESY SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hood Courtesy SW Engine hood courtesy switch ON or OFF ON: Engine hood open
OFF: Engine hood closed
-
Body Electrical > Main Body > Data List
Tester Display
Hood Courtesy SW
50003 123 200
OK:

The indicator on the GTS switches between ON and OFF in accordance with the engine hood courtesy switch (hood lock assembly) status.



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

OK (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY [ENGINE HOOD COURTESY SWITCH] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
2.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY [ENGINE HOOD COURTESY SWITCH] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the A50*1 or A59*2 hood lock assembly (engine hood courtesy switch) connector.

*1: w/ Stop and Start System

*2: w/o Stop and Start System



b.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Stop and Start System:
Tester Connection Condition Specified Condition
A50-1 (+) - G79-5 (HCTY) Always Below 1 Ω
A50-1 (+) - Body ground Always 10 kΩ or higher
G79-5 (HCTY) - Body ground Always 10 kΩ or higher

w/o Stop and Start System:
Tester Connection Condition Specified Condition
A59-1 (+) - G79-5 (HCTY) Always Below 1 Ω
A59-1 (+) - Body ground Always 10 kΩ or higher
G79-5 (HCTY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY [ENGINE HOOD COURTESY SWITCH] - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HOOD LOCK ASSEMBLY [ENGINE HOOD COURTESY SWITCH] - BODY GROUND)
a.

Disconnect the A50*1 or A59*2 hood lock assembly (engine hood courtesy switch) connector.

*1: w/ Stop and Start System

*2: w/o Stop and Start System



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Stop and Start System:
Tester Connection Condition Specified Condition
A50-2 (E) - Body ground Always Below 1 Ω

w/o Stop and Start System:
Tester Connection Condition Specified Condition
A59-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
a.

Remove the hood lock assembly (engine hood courtesy switch).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL


b.

Inspect the hood lock assembly (engine hood courtesy switch).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

OK (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)