Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048165 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Tilt Sensor Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) operates the tilt sensor (yaw rate sensor) via the CSIF communication line. The tilt sensor (yaw rate sensor) sends information regarding changes in the vehicle tilt angle to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) checks whether the vehicle body is being tilted without authorization.

WIRING DIAGRAM

B312497E01
1.76,0.25 2.594,0.458 0.833,0.208 10 false from Battery 3.51,0.438 5.135,0.615 1.625,0.177 10 false ECU-B NO.1 1.188,1.604 1.344,1.802 0.156,0.198 10 false 1 1.396,1.771 1.844,1.99 0.448,0.219 10 false GND 1.333,2.688 1.781,2.906 0.448,0.219 10 false N16 1.344,2.865 4.021,3.24 2.677,0.375 10 false Tilt Sensor (Yaw Rate Sensor Assembly) 3.5,1.75 3.948,1.969 0.448,0.219 10 false CSIF 3.594,1.219 3.885,1.438 0.292,0.219 10 false +B 3.906,1.146 4.063,1.344 0.156,0.198 10 false 6 3.906,1.635 4.063,1.833 0.156,0.198 10 false 5 5.417,1.625 5.573,1.823 0.156,0.198 10 false 6 5.635,1.76 6.25,1.958 0.615,0.198 10 false GCS 5.583,2.927 6.198,3.125 0.615,0.198 10 false G79 5.604,3.094 6.865,3.729 1.26,0.635 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.READ VALUE USING GTS (TILT SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tilt Sensor Status of the tilt sensor detection ON or OFF ON: Tilt sensor detected
OFF: Tilt sensor not detected
-
Body Electrical > Main Body > Data List
Tester Display
Tilt Sensor
50003 123 205
NOTICE:

After setting the theft deterrent system, wait 30 seconds or more (until the vehicle is in the armed state), tilt the vehicle and confirm the Data List (jack up the vehicle so that the tires are in the air).


HINT:

When performing the above inspection, have the electrical key transmitter in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding) (w/ Entry and Start System).


OK:

The display on the GTS changes according to the detection condition of the tilt sensor (yaw rate sensor assembly).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK WAVEFORM (TILT SENSOR [YAW RATE SENSOR ASSEMBLY]) (CSIF)
2.CHECK WAVEFORM (TILT SENSOR [YAW RATE SENSOR ASSEMBLY]) (CSIF)
a.

Using an oscilloscope, check the waveform.

B312498C05
3.344,0.104 3.74,0.333 0.396,0.229 4.26,1.042 4.729,0.823 false 1.906,2.854 1.74,2.75 false 2.427,2.865 2.26,2.76 false 1.49,0.177 1.802,0.333 0.313,0.156 10 false *a 1.563,2.646 1.875,2.802 0.313,0.156 10 false *b 2.094,2.646 2.406,2.802 0.313,0.156 10 false *c 3.979,2.625 4.292,2.781 0.313,0.156 10 false *d 4.021,3.177 4.333,3.333 0.313,0.156 10 false *e 2.094,3.25 2.406,3.406 0.313,0.156 10 false *f 2.521,3.229 2.854,3.552 0.333,0.323 10 false *g 2.646,3.594 2.958,3.75 0.313,0.156 10 false *h 1.5,4.104 1.802,4.344 0.302,0.24 10 false *i 4.25,4.125 4.594,4.385 0.344,0.26 10 false *j 3.417,0.135 3.729,0.292 0.313,0.156 10 false G79 4.781,0.719 5.24,0.906 0.458,0.188 10 false GCS 1.104,2.469 1.438,2.792 0.333,0.323 10 false *k 1.104,2.979 1.438,3.302 0.333,0.323 10 false *l
*a Component with harness connected
(Main Body ECU [Multiplex Network Body ECU])
*b CSIF Initial Signal
*c CSIF Initial Response *d Approximately 1.0 seconds
*e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
*g Approximately 0.05 seconds *h Approximately 5.5 seconds
*i Disarmed State *j Arming Preparation State
*k HI *l LO


Measurement Condition
Tester Connection Content
Tester Connection G79-6 (GCS) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

HINT:
·

If the tilt sensor (yaw rate sensor assembly) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TILT SENSOR [YAW RATE SENSOR ASSEMBLY] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.CHECK HARNESS AND CONNECTOR (TILT SENSOR [YAW RATE SENSOR ASSEMBLY] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the N16 yaw rate sensor assembly connector.


b.

Disconnect the G79 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N16-5 (CSIF) - G79-6 (GCS) Always Below 1 Ω
N16-1 (GND) - Body ground Always Below 1 Ω
N16-5 (CSIF) - Body ground Always 10 kΩ or higher
G79-6 (GCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TILT SENSOR (YAW RATE SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR