Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function)
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048163 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A1  Open in Driver Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for driver door) [electrical key antenna] at intervals of 0.25 seconds. For the front door outside handle assembly (for driver door) [electrical key antenna] to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the driver door at intervals of 0.25 seconds. DTC B27A1 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [electrical key antenna] (between terminals CLG1 and ANT1, or terminals CG1B and ANT2).

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B27A1 Open in Driver Side Electrical Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU [smart key ECU assembly]) (1 trip detection logic*).
·

Harness or connector

·

Front door outside handle assembly (for driver door)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for driver door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A1 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B341225E11
0.323,3.573 1.344,3.792 1.021,0.219 10 false J6*1, I6*2 1.271,0.719 1.969,0.896 0.698,0.177 10 false ANT1 1.26,1.188 1.958,1.365 0.698,0.177 10 false ANT2 1.552,1.635 2.25,1.813 0.698,0.177 10 false B 1.229,2.094 1.927,2.271 0.698,0.177 10 false SENS 1.25,2.563 1.948,2.74 0.698,0.177 10 false TRG+ 1.323,3.031 2.021,3.208 0.698,0.177 10 false GND 5.75,0.708 6.448,0.885 0.698,0.177 10 false CLG1 5.729,1.156 6.427,1.333 0.698,0.177 10 false CG1B 5.74,1.646 6.438,1.823 0.698,0.177 10 false POS1 5.74,2.083 6.438,2.26 0.698,0.177 10 false SEN1 5.75,2.563 6.448,2.74 0.698,0.177 10 false TSW1 5.729,3.021 6.427,3.198 0.698,0.177 10 false E 5.438,0.552 6.135,0.729 0.698,0.177 10 false 12 5.438,1.021 6.135,1.198 0.698,0.177 10 false 13 5.448,1.469 6.146,1.646 0.698,0.177 10 false 19 5.438,1.938 6.135,2.115 0.698,0.177 10 false 22 5.448,2.396 6.146,2.573 0.698,0.177 10 false 20 5.438,2.854 6.135,3.031 0.698,0.177 10 false 11 5.396,0.729 6.094,0.906 0.698,0.177 10 false G84 5.385,1.188 6.083,1.365 0.698,0.177 10 false G84 5.385,1.646 6.083,1.823 0.698,0.177 10 false G84 5.385,2.115 6.083,2.292 0.698,0.177 10 false G84 5.396,2.573 6.094,2.75 0.698,0.177 10 false G84 5.385,3.031 6.083,3.208 0.698,0.177 10 false G82 1.76,0.604 2.458,0.781 0.698,0.177 10 false 6 1.771,1.073 2.469,1.25 0.698,0.177 10 false 3 1.76,1.542 2.458,1.719 0.698,0.177 10 false 5 1.771,2.01 2.469,2.188 0.698,0.177 10 false 4 1.76,2.458 2.458,2.635 0.698,0.177 10 false 1 1.76,2.927 2.458,3.104 0.698,0.177 10 false 2 0.135,4.219 1.917,4.427 1.781,0.208 10 false *1: for LHD 0.125,4.479 2.229,4.729 2.104,0.25 10 false *2: for RHD 0.313,3.76 2.854,4.208 2.542,0.448 10 false Front Door Outside Handle Assembly (for Driver Door) 5.208,3.542 7.094,4.146 1.885,0.604 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The front door outside handle assembly (for driver door) has an antenna coil between ANT1 and ANT2 terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE ASSEMBLY AND BODY GROUND)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE ASSEMBLY AND BODY GROUND)

*1: for LHD

*2: for RHD


a.

Disconnect the G82 and G84 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the J6*1 or I6*2 front door outside handle assembly (for driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for LHD

Tester Connection Condition Specified Condition
G84-12 (CLG1) - J6-6 (ANT1) Always Below 1 Ω
G84-13 (CG1B) - J6-3 (ANT2) Always Below 1 Ω
G82-11 (E) - Body ground Always Below 1 Ω
J6-2 (GND) - Body ground Always Below 1 Ω
G84-12 (CLG1) or J6-6 (ANT1) - Body ground Always 10 kΩ or higher
G84-13 (CG1B) or J6-3 (ANT2) - Body ground Always 10 kΩ or higher

for RHD

Tester Connection Condition Specified Condition
G84-12 (CLG1) - I6-6 (ANT1) Always Below 1 Ω
G84-13 (CG1B) - I6-3 (ANT2) Always Below 1 Ω
G82-11 (E) - Body ground Always Below 1 Ω
I6-2 (GND) - Body ground Always Below 1 Ω
G84-12 (CLG1) or I6-6 (ANT1) - Body ground Always 10 kΩ or higher
G84-13 (CG1B) or I6-3 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA)
a.

Connect the G82 and G84 certification ECU (smart key ECU assembly) connectors.

B271427C24
2.146,0.594 2.521,0.823 0.375,0.229 4.76,0.594 5.135,0.823 0.375,0.229 2.708,1.51 2.51,2.063 2.51,2.063 2.26,2.063 false 5,1.406 5.281,2.375 5.281,2.375 5.583,2.375 false 4.833,1.406 4.552,2.375 4.552,2.375 4.25,2.375 false 0.198,0.146 0.417,0.344 0.219,0.198 10 *a 1.198,2.823 1.417,3.021 0.219,0.198 10 *b 0.969,3.635 1.333,3.802 0.365,0.167 10 GND 3.854,3.635 4.219,3.802 0.365,0.167 10 GND 4.146,2.823 4.365,3.021 0.219,0.198 10 *c 2.156,1.979 2.292,2.146 0.135,0.167 10 E 5.625,2.292 6.031,2.458 0.406,0.167 10 CLG1 3.844,2.292 4.25,2.458 0.406,0.167 10 CG1B 2.229,0.635 2.563,0.865 0.333,0.229 10 G82 4.833,0.635 5.24,0.833 0.406,0.198 10 G84
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Waveform 1
*c Waveform 2 - -



b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
G84-12 (CLG1) - G82-11 (E)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
G84-12 (CLG1) - G82-11 (E)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 2)
G84-13 (CG1B) - G82-11 (E)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 2)


*1: For details about the areas that are inside the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK



Result:
Proceed to
OK
NG



OK

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)
a.

Temporarily replace the front door outside handle assembly (for driver door) with a new or known good one.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B27A1 is not output
DTC B27A1 is output



DTC B27A1 is not output

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY [FOR DRIVER DOOR] WAS DEFECTIVE)

DTC B27A1 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)