Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0049517 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

w/ Side Airbag:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67492A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.
B337327

Detach the 2 claws and 2 clips and remove the front door lower frame bracket garnish LH.


Hide 4.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.
B337328

Using a moulding remover, detach the 2 clips, 6 claws and 2 guides and remove the power window regulator master switch assembly with front door armrest base panel.


b.

Disconnect the connector.


Hide 84820 5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.
B337002

Using a moulding remover, detach the 2 clips, 6 claws and 2 guides and remove the power window regulator master switch assembly with front door armrest base panel.


Hide 84810 7.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 74642A 8.REMOVE FRONT DOOR ASSIST GRIP COVER LH

a.
B337329

Using a moulding remover, detach the 4 claws, 2 clips and guide and remove the front door assist grip cover LH.


Hide 69284C 9.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

a.
B337330

Detach the 3 claws and remove the front door inside handle bezel plug LH.


Hide 67602 10.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B337333

Remove the 3 screws.


b.
B337331

Detach the 9 clips and remove the front door trim board sub-assembly.


c.
B337332

Disengage the front door lock remote control cable assembly LH and front door inside locking cable assembly LH from the 2 clamps.


d.

Disconnect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.


Hide 69206B 11.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B337334

Detach the 2 claws and guide and remove the front door inside handle sub-assembly LH.


Hide 68172A 12.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B337335

Raise the 7 claws of the front door inner glass weatherstrip LH as shown in the illustration, and then remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH.


Hide 87940 13.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 89835 14.REMOVE DOOR SIDE AIRBAG SENSOR LH (w/ Side Airbag)

Hide 86160 15.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY (w /Speaker)

Hide 86262E 16.REMOVE FRONT SPEAKER COVER (w/o Speaker)

a.
B338207

Disconnect the connector.


b.

Put a 4 mm (0.157 in.) drill bit into a drill.


c.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

NOTICE:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



d.

Lightly press the drill against the 3 rivets, drill off the flanges of the 3 rivets and remove the front speaker cover.

B337336E01
2.604,0.448 2.802,0.625 0.198,0.177 10 A

Standard
Area Specified Condition
A 5 mm (0.197 in.)

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




e.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


Hide 67832 17.REMOVE FRONT DOOR SERVICE HOLE COVER LH

a.
B338198C01
0.625,3.281 0.833,3.469 0.208,0.188 10 *A
*A w/ Side Airbag Sensor


Disconnect the connector.


b.

w/ Side Airbag Sensor:

Remove the bolt as shown in the illustration.


c.

Using a clip remover, detach the 3 clamps.


d.

Pull out the front door lock remote control cable assembly LH, front door inside locking cable assembly LH and wire harness from the front door service hole cover LH, and then remove the front door service hole cover LH.

HINT:

Remove any remaining butyl tape from the front door panel.



Hide 68102 18.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Temporarily install the power window regulator master switch assembly with front door armrest base panel.


b.

Connect the power window regulator motor.


c.

Connect the negative (-) battery terminal.


d.

Move the front door window regulator so that the front door glass bolts can be seen.


e.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



f.

Remove the power window regulator master switch assembly with front door armrest base panel.


g.
B337338

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass to fall.



h.
B337339N01
0.604,0.552 0.958,0.75 0.354,0.198 10 (1) 1.854,0.26 2.135,0.458 0.281,0.198 10 (2)

Remove the front door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the front door glass.



Hide 68151D 19.REMOVE FRONT DOOR GLASS RUN LH

a.
B337341

Remove the front door glass run LH.


Hide 69802 20.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B337340C01
2.094,1.146 1.844,0.354 1.844,0.354 1.625,0.354 true 1.479,0.271 1.698,0.448 0.219,0.177 10 *1
*1 Temporary Bolt


Disconnect the connector.


b.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly LH may fall and become damaged.



c.

Remove the 5 bolts and front door window regulator sub-assembly LH.


d.

Remove the temporary bolt from the front door window regulator sub-assembly LH.


Hide 85720C 21.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 67404F 22.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B337342

Remove the bolt.


b.
B337343

Detach the guide and remove the front door rear lower frame sub-assembly LH.


Hide 67924 23.REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION

a.
B338197C01
1.552,1.052 1.594,1.125 false
V100155

Double-sided Tape


Remove the 2 bolts.


b.

Detach the 2 guides, and remove the double-sided tape and front door No. 2 stiffener cushion.

NOTICE:

Remove any remaining tape from the door.



Hide 75720 24.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 69217F 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH

a.
B338129C01
3,1.615 3,1.271 false 2.927,1.646 3.24,1.802 0.313,0.156 10 *1
*1 Hole Plug


Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover LH together with the door lock cylinder LH.


Hide 69052 26.REMOVE DOOR LOCK CYLINDER LH

a.
B337345

Detach the 2 claws and remove the door lock cylinder LH from the front door outside handle cover LH.


Hide 69040A 27.REMOVE FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

Hide 69720B 28.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B337353C02
0.031,0.052 0.344,0.208 0.313,0.156 10 *A 0.063,1.854 0.375,2.01 0.313,0.156 10 *B
*A w/o Double Locking System
*B w/ Double Locking System


Remove the front door lock remote control cable assembly LH.


Hide 69760C 29.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B337354C01
0.125,0.135 0.438,0.292 0.313,0.156 10 *A 0.125,1.75 0.438,1.906 0.313,0.156 10 *B
*A w/o Double Locking System
*B w/ Double Locking System


Detach the 3 claws and open the cover.


b.
B337355C01
0.094,0.198 0.406,0.354 0.313,0.156 10 *A 0.104,1.698 0.417,1.854 0.313,0.156 10 *B
*A w/o Double Locking System
*B w/ Double Locking System


Remove the front door inside locking cable assembly LH.


Hide 69220 30.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.

w/ Entry and Start System:

i.
B337346C01
2.333,0.844 2.656,0.542 2.656,0.542 2.844,0.542 false 2.854,0.448 3.052,0.635 0.198,0.188 10 *1
*1 Protective Tape


Using a screwdriver, detach the 2 claws of the connector cover in the direction indicated by the arrow in the illustration and disconnect the connector cover.

HINT:

Tape the screwdriver tip before use.



ii.
B338126C01
1.958,1 2.26,0.594 2.26,0.594 2.573,0.594 false 2.594,0.5 2.74,0.677 0.146,0.177 10 *1
*1 Protective Tape


Using a screwdriver, detach the claw of the connector in the direction indicated by the arrow in the illustration and disconnect the connector.

HINT:

Tape the screwdriver tip before use.




b.
B337347

Remove the front door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.


Hide 69241H 31.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B337350

Detach the 3 claws and remove the front door front outside handle pad.


Hide 69242F 32.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B337351

Detach the 2 claws and remove the front door rear outside handle pad.


Hide 69202A 33.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B338196

w/ Entry and Start System:

Detach the 3 clamps.


b.
B338199C01
0.052,0.031 0.365,0.188 0.313,0.156 10 *A 0.052,2.26 0.365,2.417 0.313,0.156 10 *B
*A Inside
*B Outside


Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle frame sub-assembly LH.


c.

Slide the front door outside handle frame sub-assembly LH to detach the claw of the front door outside handle frame sub-assembly LH, and then remove it.


Hide 69312 34.REMOVE FRONT DOOR LOCK OPEN ROD LH

a.
B332412C01
2.604,0.656 3.052,0.333 true 2.552,0.104 3.01,0.302 0.458,0.198 10 (1) 2.729,0.854 3.188,1.052 0.458,0.198 10 (2) 3.021,0.208 3.208,0.396 0.188,0.188 10 *1
*1 Snap


Rotate the snap to detach the snap, and then remove the front door lock open rod LH as indicated by the arrows in the order shown in the illustration.


Hide 68620 35.REMOVE FRONT DOOR CHECK ASSEMBLY LH

a.
B337360

Remove the 3 bolts and front door check assembly LH.


Hide 67862 36.REMOVE FRONT DOOR WEATHERSTRIP LH

a.
B337356

Using a clip remover, remove the 2 clips.


b.

Using a clip remover, detach the 18 clips and remove the front door weatherstrip LH.


Hide 67664C 37.REMOVE DOOR FRAME GARNISH LH

a.
B337359

Detach the claw and remove the door frame garnish LH.


Hide 75792 38.REMOVE DOOR WINDOW FRAME MOULDING CLIP

Hide 75756C 39.REMOVE FRONT DOOR WINDOW REAR FRAME MOULDING LH

Hide 75922M 40.REMOVE NO. 1 BLACK OUT TAPE LH

Hide 75074 41.REMOVE FRONT DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY LH

Hide 67001A 42.REMOVE FRONT DOOR PANEL CUSHION

a.
B337357

Detach the 2 claws and remove the 2 front door panel cushions.