Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function)
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048163 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the front passenger door only, but the entry lock function operates, the request code is being transmitted properly from the front passenger door. In this case, there may be a problem related to the touch sensor (connection between the certification ECU [smart key ECU assembly] and front door outside handle assembly [for front passenger door] [unlock sensor]).

WIRING DIAGRAM

B341225E05
0.323,3.479 1.365,3.677 1.042,0.198 10 false I6*1, J6*2 1.271,0.719 1.969,0.896 0.698,0.177 10 false ANT1 1.26,1.188 1.958,1.365 0.698,0.177 10 false ANT2 1.542,1.635 2.24,1.813 0.698,0.177 10 false B 1.24,2.094 1.938,2.271 0.698,0.177 10 false SENS 1.24,2.563 1.938,2.74 0.698,0.177 10 false TRG+ 1.323,3.031 2.021,3.208 0.698,0.177 10 false GND 5.75,0.708 6.448,0.885 0.698,0.177 10 false CLG2 5.729,1.156 6.427,1.333 0.698,0.177 10 false CG2B 5.74,1.646 6.438,1.823 0.698,0.177 10 false POS2 5.75,2.083 6.448,2.26 0.698,0.177 10 false SEN2 5.75,2.563 6.448,2.74 0.698,0.177 10 false TSW2 5.729,3.021 6.427,3.198 0.698,0.177 10 false E 5.438,0.552 6.135,0.729 0.698,0.177 10 false 11 5.438,1.021 6.135,1.198 0.698,0.177 10 false 10 5.448,1.469 6.146,1.646 0.698,0.177 10 false 21 5.438,1.938 6.135,2.115 0.698,0.177 10 false 23 5.448,2.396 6.146,2.573 0.698,0.177 10 false 8 5.438,2.854 6.135,3.031 0.698,0.177 10 false 11 5.375,0.729 6.073,0.906 0.698,0.177 10 false G84 5.365,1.188 6.063,1.365 0.698,0.177 10 false G84 5.365,1.646 6.063,1.823 0.698,0.177 10 false G84 5.365,2.115 6.063,2.292 0.698,0.177 10 false G84 5.375,2.573 6.073,2.75 0.698,0.177 10 false G84 5.375,3.031 6.073,3.208 0.698,0.177 10 false G82 1.76,0.604 2.458,0.781 0.698,0.177 10 false 6 1.771,1.073 2.469,1.25 0.698,0.177 10 false 3 1.76,1.542 2.458,1.719 0.698,0.177 10 false 5 1.771,2.01 2.469,2.188 0.698,0.177 10 false 4 1.76,2.458 2.458,2.635 0.698,0.177 10 false 1 1.76,2.927 2.458,3.104 0.698,0.177 10 false 2 0.135,4.219 1.917,4.406 1.781,0.188 10 false *1: for LHD 0.125,4.479 2.219,4.667 2.094,0.188 10 false *2: for RHD 0.313,3.635 2.635,4.208 2.323,0.573 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 5.208,3.542 7.104,4.094 1.896,0.552 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Proceed to
Door locks operate normally
Door locks do not operate



Door locks operate normally

2.READ VALUE USING GTS (UNLOCK DETECTION SWITCH)

Door locks do not operate

2.READ VALUE USING GTS (UNLOCK DETECTION SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front RH door unlock detection switch signal*1 UNLOCK or LOCK UNLOCK: Front RH door unlocked
LOCK: Front RH door locked
-
FL Door Lock Pos Front RH door unlock detection switch signal*2 UNLOCK or LOCK UNLOCK: Front LH door unlocked
LOCK: Front LH door locked
-
·

*1: for LHD

·

*2: for RHD



OK:

On the GTS screen, the display changes between LOCK and UNLOCK as shown in the chart above.


Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (UNLOCK SENSOR)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

3.READ VALUE USING GTS (UNLOCK SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Door Touch Sensor Front passenger door touch sensor (unlock sensor) ON or OFF ON: Front passenger door touch sensor (unlock sensor) touched
OFF: Front passenger door touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).


·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly (for front passenger door side).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY - CERTIFICATION ECU AND BODY GROUND)
a.

Disconnect the I6*1 or J6*2 front door outside handle assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G82 and G84 certification ECU (smart key ECU assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
I6-4 (SENS) - G84-23 (SEN2) Always Below 1 Ω
G82-11 (E) - Body ground Always Below 1 Ω
I6-4 (SENS) or G84-23 (SEN2) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
J6-4 (SENS) - G84-23 (SEN2) Always Below 1 Ω
G82-11 (E) - Body ground Always Below 1 Ω
J6-4 (SENS) or G84-23 (SEN2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (FRONT PASSENGER DOOR UNLOCK SENSOR SIGNAL INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (FRONT PASSENGER DOOR UNLOCK SENSOR SIGNAL INPUT)
a.

Connect the I6*1 or J6*2 front door outside handle assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD


B274842C36
2.063,0.833 2.438,1.063 0.375,0.229 4.646,0.833 5.021,1.063 0.375,0.229 2.656,1.688 2.844,2.25 false 5,1.698 5.229,2.25 false 5.021,3.292 5.5,2.958 5.5,2.958 5.333,3.292 false 0.573,0.448 0.948,0.656 0.375,0.208 10 *a 4.167,2.781 4.594,2.969 0.427,0.188 10 *b 3.969,3.854 4.354,4.104 0.385,0.25 10 GND 2.802,2.313 3,2.552 0.198,0.24 10 E 5.458,2.781 5.833,2.99 0.375,0.208 10 *c 2.146,0.875 2.469,1.042 0.323,0.167 10 G82 4.719,0.875 5.042,1.042 0.323,0.167 10 G84 5.104,2.292 5.656,2.531 0.552,0.24 10 SEN2
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b Waveform
*c In actuality, sampling is being performed - -



b.

Connect the G82 and G84 certification ECU (smart key ECU assembly) connectors.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
G84-23 (SEN2) - G82-11 (E)
Procedure
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)