If the entry lock function does not operate for the driver door only, but the entry unlock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the front door outside handle assembly (for driver door) (lock sensor) (connection between the certification ECU [smart key ECU assembly] and front door outside handle assembly [for driver door] [lock sensor]).
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Proceed to |
|---|
| Door locks operate normally |
| Door locks do not operate |
Door locks operate normally
Door locks do not operate
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry & Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D-Door Trigger Switch | Driver door touch sensor (lock sensor) | ON or OFF | ON: Driver door touch sensor (lock sensor) touched
OFF: Driver door touch sensor (lock sensor) not touched |
·
Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate. |
The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J6*1 or I6*2 front door outside handle assembly (for driver door) connector.
*1: for LHD
*2: for RHD
Disconnect the G82 and G84 certification ECU (smart key ECU assembly) connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J6-1 (TRG+) - G84-20 (TSW1) | Always | Below 1 Ω |
| G82-11 (E) - Body ground | Always | Below 1 Ω |
| J6-1 (TRG+) or G84-20 (TSW1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-1 (TRG+) - G84-20 (TSW1) | Always | Below 1 Ω |
| G82-11 (E) - Body ground | Always | Below 1 Ω |
| I6-1 (TRG+) or G84-20 (TSW1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the J6*1 or I6*2 front door outside handle assembly (for driver door) connector.
*1: for LHD
*2: for RHD
| *a | Component with harness connected
(Certification ECU [Smart Key ECU Assembly]) |
*b | Waveform |
| *c | In actuality, sampling is being performed | - | - |
Connect the G82 and G84 certification ECU (smart key ECU assembly) connectors.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G84-20 (TSW1) - G82-11 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Driver door lock sensor not touched → touched |
2 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG