Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0048746 LANE DEPARTURE ALERT SYSTEM J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the lane departure warning camera.

WIRING DIAGRAM

E270481E01
5.073,2.021 7.115,2.24 2.042,0.219 10 Lane Departure Warning Camera 5.083,1.854 5.542,2.052 0.458,0.198 10 Q13 5.75,1.292 6.208,1.49 0.458,0.198 10 GND 5.75,0.333 6.208,0.531 0.458,0.198 10 IGB 5.51,0.219 5.667,0.417 0.156,0.198 10 7 5.438,1.167 5.75,1.365 0.313,0.198 10 11 3.771,0.188 4.083,0.385 0.313,0.198 10 *1 3.771,0.771 4.083,0.969 0.313,0.198 10 *2 2.542,0.542 3.542,0.792 1,0.25 10 ECU-IG1 NO.2 0.583,0.333 2.01,0.604 1.427,0.271 10 from IG1 NO.1 Relay 0.313,0.958 2.406,1.208 2.094,0.25 10 from Engine Stop and Start ECU 0.313,2.031 4.75,2.229 4.438,0.198 10 *1: w/o Stop and Start System 0.313,2.354 4.594,2.552 4.281,0.198 10 *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

w/ Stop and Start System:

Check the stop and start system function by following How to Proceed with Troubleshooting. Troubleshoot the lane departure alert system after confirming that the stop and start system is functioning properly.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (LANE DEPARTURE WARNING CAMERA - BATTERY AND BODY GROUND)
a.

Disconnect the lane departure warning camera connector.


b.
E255432C01
0.375,0.802 0.781,1.042 0.406,0.24 1.031,1.771 1.292,1.427 true 1.979,1.417 2.365,1.729 true 0.427,0.833 0.802,1.031 0.375,0.198 10 Q13 0.073,0.073 0.385,0.271 0.313,0.198 10 *a 0.74,1.698 1.198,1.896 0.458,0.198 10 IGB 2.438,1.667 2.896,1.865 0.458,0.198 10 GND
*a Front view of harness connector
(to Lane Departure Warning Camera)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/o Start and Stop System

*2: w/ Start and Stop System

Q13-7 (IGB) - Body ground Ignition switch ON 11 to 14 V*1
Ignition switch ON 10.5 to 14 V*2
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-11 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR