Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMBUSTION TYPE POWER HEATER SYSTEM
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049438 COMBUSTION TYPE POWER HEATER SYSTEM J

HEATING / AIR CONDITIONING  COMBUSTION TYPE POWER HEATER SYSTEM  Power Heater Switch Circuit  


DESCRIPTION

When the heater switch assembly is turned on, the heater assembly sends a drive signal to the heater pump assembly. The heater assembly then receives the fuel necessary for combustion and starts operating.

WIRING DIAGRAM

E267496E01
2.448,1.417 2.76,1.615 0.313,0.198 10 G1 2.448,1.615 4.073,1.813 1.625,0.198 10 Heater Switch Assembly 2.542,1.073 2.854,1.271 0.313,0.198 10 E 2.552,0.76 2.865,0.958 0.313,0.198 10 IG 3.635,0.76 3.844,0.927 0.208,0.167 10 IN 5.521,0.646 5.833,0.844 0.313,0.198 10 IG 5.521,2.198 5.833,2.396 0.313,0.198 10 CHI 5.333,2.094 5.469,2.271 0.135,0.177 10 4 5.323,0.542 5.469,0.708 0.146,0.167 10 3 3.896,0.542 4.208,0.74 0.313,0.198 10 1 2.365,0.542 2.521,0.729 0.156,0.188 10 4 2.365,0.865 2.5,1.052 0.135,0.188 10 5 0.406,0.646 1.635,0.823 1.229,0.177 10 from HTR-IG Fuse 5.5,1.146 5.813,1.344 0.313,0.198 10 A33 5.5,1.333 6.667,1.531 1.167,0.198 10 Heater Assembly 5.323,2.698 5.635,2.896 0.313,0.198 10 G87 5.323,2.885 7.063,3.083 1.74,0.198 10 Engine Stop and Start ECU* 0.156,3.375 2.51,3.583 2.354,0.208 10 *: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
E176908C02
1.458,0.219 1.938,0.51 0.479,0.292 2.208,1.302 2.521,1.49 2.521,1.49 2.698,1.49 true 1.927,1.396 2.26,1.813 2.26,1.813 2.438,1.813 true 0.083,0.031 0.26,0.198 0.177,0.167 10 *a 2.75,1.417 2.875,1.583 0.125,0.167 10 E 1.604,0.271 1.917,0.448 0.313,0.177 10 G1 2.5,1.729 2.76,1.885 0.26,0.156 10 IG
*a Front view of wire harness connector
(to Heater Switch Assembly)


Disconnect the heater switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G1-4 (IG) - Body ground Ignition switch ON 11 to 14 V
G1-4 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT HEATER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT HEATER SWITCH ASSEMBLY
a.
E176907N01
1.177,1.167 0.635,1.167 0.635,1.167 1.188,1.167 true 1.385,1.219 0.99,1.615 0.99,1.615 0.75,1.615 true 2.125,1.167 2.875,1.167 true 0.458,1.073 0.656,1.302 0.198,0.229 10 E 0.552,1.531 0.771,1.74 0.219,0.208 10 IG 2.927,1.104 3.156,1.323 0.229,0.219 10 IN

Remove the heater switch assembly.


b.

Measure the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (IG) - 1 (IN) Heater switch assembly ON Below 1 Ω
4 (IG) - 1 (IN) Heater switch assembly off 10 kΩ or higher




c.

Check operation indicator.

i.

Turn the heater switch assembly on.


ii.

Connect a positive (+) lead from the battery to terminal 4 (IG) and a negative (-) lead to terminal 5 (E), and check that the operation indicator comes on.

OK:

Indicator comes on.




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - HEATER ASSEMBLY, ENGINE STOP AND START ECU)

NG

REPLACE HEATER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - HEATER ASSEMBLY, ENGINE STOP AND START ECU)
a.

Disconnect the G1 heater switch assembly connector.


b.

Disconnect the A33 heater assembly connector.


c.

Disconnect the G87 engine stop and start ECU connector.*


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/ Stop and Start System

G1-1 (IN) - A33-3 (IG) Always Below 1 Ω
G1-1 (IN) - G87-4 (CHI)* Always Below 1 Ω
A33-3 (IG) - Body ground Always 10 kΩ or higher
G87-4 (CHI) - Body ground* Always 10 kΩ or higher



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR