Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY(for LHD)
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0049516 HOOD LOCK CONTROL CABLE ASSEMBLY(for LHD) A

DOOR / HATCH  HOOD LOCK CONTROL CABLE ASSEMBLY(for LHD)  INSTALLATION  


PROCEDURE

Hide 53630 1.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY

a.
B277362C14
1.542,1.231 1.729,1.392 0.187,0.162 10 *1 1.751,1.326 2.492,1.326 false
*1 String


Tie the string that was passed through the engine compartment room to the end of the hood lock control cable assembly as shown in the illustration.

HINT:

Use a length of string long enough to pass through the engine compartment room.



b.

Pass the hood lock control cable assembly through the vehicle body, and then attach each clamp.


c.

Untie the string from the hood lock control cable assembly.

B338124C06
5.76,5.271 6.344,5.063 true 4.698,5.438 5.146,5.531 true 4.635,5 5.094,4.677 true 2.573,5.49 3.208,5.396 true 0.917,4.573 1.583,4.333 true 0.563,4.031 1.229,3.792 true 0.823,1.344 0.823,2.063 true 6.813,5.635 6.792,5.094 true 5.594,5.219 5.906,5.375 0.313,0.156 10 *1 5.125,4.573 5.438,4.729 0.313,0.156 10 *2 5.188,5.469 5.5,5.625 0.313,0.156 10 *1 2.406,5.406 2.719,5.563 0.313,0.156 10 *1 0.75,4.51 1.063,4.667 0.313,0.156 10 *1 0.385,3.979 0.698,4.135 0.313,0.156 10 *1 0.781,1.198 1.094,1.354 0.313,0.156 10 *1 6.76,5.646 7.073,5.802 0.313,0.156 10 *2
*1 Hood Lock Control Cable *2 Stopper



Hide 53510 2.INSTALL HOOD LOCK ASSEMBLY

a.

Apply MP grease to the sliding parts of the hood lock assembly.


b.

Connect the hood lock control cable to the hood lock assembly.


c.

Install the hood lock assembly with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

w/ Engine Hood Courtesy Switch:

Connect the connector.


Hide 53601 3.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.

Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.


b.

Attach the 3 claws to install the hood lock control lever sub-assembly.


Hide 55545 4.INSTALL FUSE BOX OPENING COVER

Hide 62112 5.INSTALL COWL SIDE TRIM BOARD LH

Hide 67914B 6.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 55701J 7.INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY

Hide 53388D 8.INSTALL HOOD TO FRONT FENDER SEAL RH

B340664

a.

Attach the 3 clips to install the hood to front fender seal RH.


b.

Install the clip.


Hide 53389B 9.INSTALL HOOD TO FRONT FENDER SEAL LH

HINT:

Use the same procedure described for the RH side.


Hide 10.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY