Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM3090E _55 Steering _008773 STEERING COLUMN _0049531 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS. Read the precautionary notices concerning the SRS before servicing the steering column.

w/ Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>PRECAUTION

w/o Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION


HINT:
·

Use the same procedure for RHD and LHD vehicles.


·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 45286 5.REMOVE STEERING COLUMN COVER

NOTICE:

Failure to follow the correct removal procedure may damage the claws.


a.
C275617

Remove the 2 screws.


b.

Release the tilt lever.


c.

Press both sides of the lower steering column cover to detach the 2 claws.


d.
C275618

Detach the claw to remove the lower steering column cover.


e.
C275619

Detach the 3 claws, 4 clips and 2 pins and remove the upper steering column cover.


Hide 6.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.

Disconnect the connectors from the combination switch assembly with spiral cable sub-assembly.


b.
C316360

Detach the 3 claws. Remove the combination switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 55606 8.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55432B 9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Driver Side Knee Airbag)

Hide 73900 10.REMOVE NO. 1 LOWER INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 45259A 11.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C128486

Fold back the floor carpet, and then remove the 2 clips and column hole cover silencer sheet.


Hide 45260 12.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C275682C01
1.115,1.906 0.771,1.552 0.771,1.552 1.146,1.802 true 0.615,1.438 0.927,1.594 0.313,0.156 10 *a 1.979,1.115 2.292,1.271 0.313,0.156 10 *b
*a Matchmark
*b Slide


Place matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft assembly.


b.

Remove the bolt.


c.

Disconnect the No. 2 steering intermediate shaft assembly from the steering intermediate shaft assembly.


Hide 4520A 13.REMOVE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY

a.
C275636

Disconnect the 2 connectors and 3 clamps.


b.

Remove the bolt and disconnect the harness cable.


c.
C335311

Remove the bolt, 2 nuts and steering column assembly.

NOTICE:
·

Do not release the tilt lever when the steering column assembly is not installed to the vehicle.

·

Do not drop or strike the steering column assembly. If dropped or struck, replace it with a new one.




Hide 45260 14.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.

Remove the bolt.

NOTICE:

Do not remove the No. 2 steering intermediate shaft assembly from the steering column assembly.



b.
C275622C01
1.792,0.938 1.229,0.323 1.229,0.323 1.885,0.865 true 1.042,0.188 1.354,0.344 0.313,0.156 10 *a
*a Matchmark


Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


c.

Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.