*1: for LHD
*2: for RHD
This DTC is stored when LIN communication between the front power window regulator motor assembly LH*1 or front power window regulator motor assembly RH*2 and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2321 | Driver Side Door ECU Communication Stop | No communication between the front power window regulator motor assembly (driver side) and main body ECU for 10 seconds or more. | ·
Front power window regulator motor assembly LH*1 ·
Front power window regulator motor assembly RH*2 ·
Main body ECU (multiplex network body ECU) ·
Harness or connector ·
Instrument panel junction block assembly |
When using the GTS with the ignition switch off to troubleshoot:
Connect the GTS to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When the front power window regulator motor assembly (driver side) is removed and reinstalled or replaced, the front power window regulator motor assembly (driver side) must be initialized.
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
When DTC B2321 and B2325 are output simultaneously, perform troubleshooting for DTC B2325 first.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>B2325
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result |
|---|
| NEXT |
NEXT
Check for DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B2321 is output |
| DTC B2321 is not output |
DTC B2321 is output
DTC B2321 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Disconnect the J3 front power window regulator motor assembly LH*1 or I3 front power window regulator motor assembly RH*2 connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-16 (LIN2) - J3-9 (LIN) | Always | Below 1 Ω |
| A-16 (LIN2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-16 (LIN2) - I3-9 (LIN) | Always | Below 1 Ω |
| A-16 (LIN2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly) |
Disconnect the J3 front power window regulator motor assembly LH*1 or I3 front power window regulator motor assembly RH*2 connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J3-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I3-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J3-2 (B) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I3-2 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Temporarily replace the front power window regulator motor assembly LH with a new or normally functioning one.
for RHD
Temporarily replace the front power window regulator motor assembly RH with a new or normally functioning one.
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B2321 is not output |
| DTC B2321 is output (for LHD) |
| DTC B2321 is output (for RHD) |
DTC B2321 is not output
DTC B2321 is output (for LHD)
DTC B2321 is output (for RHD)
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Disconnect the J3 front power window regulator motor assembly LH*1 or I3 front power window regulator motor assembly RH*2 connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-54 - J3-9 (LIN) | Always | Below 1 Ω |
| 3D-54 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-54 - I3-9 (LIN) | Always | Below 1 Ω |
| 3D-54 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK (for LHD) |
| OK (for RHD) |
| NG |
OK (for LHD)
OK (for RHD)
NG