Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3090E _57 Power Source / Network _008434 NETWORKING _0047063 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors and sliding roof drive gear sub-assembly. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors and sliding roof drive gear sub-assembly is detected consecutively 3 times.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2325 LIN Communication Bus Malfunction Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.
·

Front power window regulator motor assembly LH*1

·

Front power window regulator motor assembly RH*2

·

Double lock door control relay assembly*3

·

Sliding roof drive gear sub-assembly*4

·

Main body ECU (multiplex network body ECU)

·

Harness or connector

·

Instrument panel junction block assembly



*1: for LHD, w/ Jam Protection Function

*2: for RHD, w/ Jam Protection Function

*3: w/ Double Locking System

*4: w/ Sliding Roof System


WIRING DIAGRAM

B339671E03
1.51,1.49 3.177,1.969 1.667,0.479 10 false Instrument Panel Junction Block Assembly 1.51,1.302 1.823,1.5 0.313,0.198 10 false 3D 3.01,0.635 3.25,0.833 0.24,0.198 10 false 54 1.021,0.771 1.365,0.979 0.344,0.208 10 false LIN2 0.229,2.583 0.385,2.781 0.156,0.198 10 false A 0.208,2.771 1.865,3.198 1.656,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 4.927,1.271 6.885,1.656 1.958,0.385 10 false Front Power Window Regulator Motor Assembly LH*1 4.917,2.708 6.854,3.083 1.938,0.375 10 false Front Power Window Regulator Motor Assembly RH*2 1.438,0.635 1.75,0.833 0.313,0.198 10 false 16 0.698,5.438 2.333,5.719 1.635,0.281 10 false : LIN Communication Line 4.938,5.24 6.594,5.646 1.656,0.406 10 false Double Lock Door Control Relay Assembly*4 4.583,4.052 7.083,4.26 2.5,0.208 10 false Sliding Roof Drive Gear Sub-assembly*3 0.271,3.958 3,4.146 2.729,0.188 10 false *1: for LHD, w/ Jam Protection Function 0.26,4.313 2.958,4.552 2.698,0.24 10 false *2: for RHD, w/ Jam Protection Function 0.26,4.656 1.958,4.927 1.698,0.271 10 false *3: w/ Sliding Roof System 0.26,5.01 2.177,5.271 1.917,0.26 10 false *4: w/ Double Locking System 4.719,3.427 5.031,3.625 0.313,0.198 10 false 11 4.958,3.563 5.573,3.76 0.615,0.198 10 false MPX1 4.667,3.885 4.979,4.083 0.313,0.198 10 false Q8 4.781,0.625 4.938,0.823 0.156,0.198 10 false 9 4.792,2.073 4.948,2.271 0.156,0.198 10 false 9 4.927,5.063 5.385,5.26 0.458,0.198 10 false G66 4.781,4.604 4.938,4.802 0.156,0.198 10 false 9 4.958,4.729 5.573,4.927 0.615,0.198 10 false MPX1 4.969,2.208 5.427,2.406 0.458,0.198 10 false LIN 4.969,0.75 5.427,0.948 0.458,0.198 10 false LIN 4.906,1.083 5.219,1.281 0.313,0.198 10 false J3 4.906,2.531 5.125,2.76 0.219,0.229 10 false I3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

When a power window regulator motor assembly (driver side) is removed and reinstalled or replaced, a power window regulator motor assembly (driver side) must be initialized.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

·

When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



HINT:

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform troubleshooting for DTC B2325. Then perform troubleshooting for the LIN communication stop DTC.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
DTC B2325 is output
DTC B2325 is not output



DTC B2325 is output

3.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

DTC B2325 is not output

3.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

*1: w/ Sliding Roof System

*2: for LHD, w/ Jam Protection Function

*3: for RHD, w/ Jam Protection Function

*4: w/ Double Locking System


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Disconnect the Q8 sliding roof drive gear sub-assembly*1 connector.


c.

Disconnect the J3 front power window regulator motor assembly LH*2 connector.


d.

Disconnect the I3 front power window regulator motor assembly RH*3 connector.


e.

Disconnect the G66 double lock door control relay assembly*4 connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - Q8-11 (MPX1)*1 Always Below 1 Ω
A-16 (LIN2) - J3-9 (LIN)*2 Always Below 1 Ω
A-16 (LIN2) - I3-9 (LIN)*3 Always Below 1 Ω
A-16 (LIN2) - G66-9 (MPX1)*4 Always Below 1 Ω
Q8-11 (MPX1) - Body ground*1 Always 10 kΩ or higher
J3-9 (LIN) - Body ground*2 Always 10 kΩ or higher
I3-9 (LIN) - Body ground*3 Always 10 kΩ or higher
G66-9 (MPX1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

10.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
4.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
NOTICE:

For vehicles without a sliding roof system, go to "Clear DTC".


a.

Disconnect the Q8 sliding roof drive gear assembly connector.


b.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
DTC B2325 is output
DTC B2325 is not output



DTC B2325 is output

6.CLEAR DTC

DTC B2325 is not output

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

6.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
NOTICE:

For vehicles without a double locking system, go to "Clear DTC".


a.

Disconnect the G66 double lock door control relay assembly connector.


b.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
DTC B2325 is output
DTC B2325 is not output



DTC B2325 is output

8.CLEAR DTC

DTC B2325 is not output

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

8.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Disconnect the J3 front power window regulator motor assembly LH*1 or I3 front power window regulator motor assembly RH*2 connector.


*1: for LHD

*2: for RHD


b.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Proceed to
DTC B2325 is output (for LHD)
DTC B2325 is output (for RHD)
DTC B2325 is not output (for LHD)
DTC B2325 is not output (for RHD)



DTC B2325 is output (for LHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

DTC B2325 is output (for RHD)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

DTC B2325 is not output (for LHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

DTC B2325 is not output (for RHD)

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

10.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

*1: w/ Sliding Roof System

*2: for LHD, w/ Jam Protection Function

*3: for RHD, w/ Jam Protection Function

*4: w/ Double Locking System


a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Disconnect the Q8 sliding roof drive gear sub-assembly*1 connector.


c.

Disconnect the J3 front power window regulator motor assembly LH*2 connector.


d.

Disconnect the I3 front power windowregulator motor assembly RH*3 connector.


e.

Disconnect the G66 double lock door control relay assembly*4 connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-54 - Q8-11 (MPX1)*1 Always Below 1 Ω
3D-54 - J3-9 (LIN)*2 Always Below 1 Ω
3D-54 - I3-9 (LIN)*3 Always Below 1 Ω
3D-54 - G66-9 (MPX1)*4 Always Below 1 Ω
Q8-11 (MPX1) - Body ground*1 Always 10 kΩ or higher
J3-9 (LIN) - Body ground*2 Always 10 kΩ or higher
I3-9 (LIN) - Body ground*3 Always 10 kΩ or higher
G66-9 (MPX1) - Body ground*4 Always 10 kΩ or higher



Result:
Result
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK (for RHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR