Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2012.12–2014.10
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047096 DIFFERENTIAL CASE A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41331Q 1.INSTALL DIFFERENTIAL SIDE GEAR

a.
C278985C01
2.594,0.448 2.927,0.448 false 0.76,0.396 1.094,0.396 false 0.771,0.729 1.104,0.729 false 1.438,1.625 1.771,1.625 false 1.448,1.927 1.781,1.927 false 1.948,0.51 1.813,0.51 1.813,0.51 1.76,0.781 false 0.792,1.583 0.74,1.854 0.74,1.854 0.604,1.854 false 1.188,1 1.521,1 false 1.021,1.385 1.354,1.385 false 3,0.365 3.313,0.521 0.313,0.156 10 false *1 0.583,0.646 0.896,0.802 0.313,0.156 10 false *2 0.573,0.302 0.885,0.458 0.313,0.156 10 false *3 1.406,1.313 1.719,1.469 0.313,0.156 10 false *4 2,0.438 2.313,0.594 0.313,0.156 10 false *5 1.833,1.844 2.146,2 0.313,0.156 10 false *3 1.823,1.542 2.135,1.698 0.313,0.156 10 false *2 0.438,1.771 0.75,1.927 0.313,0.156 10 false *5 1.01,0.927 1.323,1.083 0.313,0.156 10 false *4
*1 Differential Case
*2 Differential Side Gear
*3 No. 1 Front Differential Side Gear Thrust Washer
*4 Front Differential Pinion
*5 Front Differential Pinion Thrust Washer


Coat the 2 differential side gears, 2 No. 1 front differential side gear thrust washers, 2 front differential pinions and 2 front differential pinion thrust washers with ATF and install them to the differential case.


Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C313975C01
0,0 0,0 false
V100135

Toyota Genuine ATF WS


Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.


Hide 3.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C313973

Using a pin 3 mm punch and hammer, install the front differential pinion shaft straight pin.

NOTICE:

Align the holes, and install the front differential pinion shaft straight pin.



b.
C313972

Using a chisel and hammer, stake the differential case.

NOTICE:

Stake the differential case after adjusting the backlash.



Hide 41221 5.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the front differential ring gear to more than 110°C (230°F).



b.

Clean the contact surface of the front differential case.


c.
C323295C01
1.177,1.594 0.646,1.042 0.646,1.042 1.26,1.531 true 0.427,0.906 0.74,1.104 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks, and install the front differential ring gear case quickly.

NOTICE:

Do not install the bolts while the front differential ring gear is hot.



d.
C323296

Install and tighten the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:

Tighten the bolts a little at a time in a diagonal sequence.



Hide 31105H 6.INSTALL TRANSAXLE CASE OIL SEAL RH (INNER)

a.

Coat the lip of a new transaxle case oil seal RH (inner) with MP grease.


b.
C324343N01
2.219,0.865 2,0.354 2,0.354 2.417,0.594 true 1.667,0.229 2.125,0.427 0.458,0.198 10 false SST

Using SST and a hammer, install the transaxle case oil seal RH (inner).

SST
09950-60010  (09951-00410)
09950-70010  (09951-07200)

Oil seal drive in depth:

21.5 to 22.5 mm (0.846 to 0.886 in.)