Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047092 AUTOMATIC TRANSAXLE UNIT A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 35104V 1.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C206503

Using a screwdriver, remove the transmission breather hose sub-assembly from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.



b.
C190664C01
1.354,0.219 1.219,0.219 1.219,0.219 1.135,0.458 false 2.188,1.344 2.052,1.344 2.052,1.344 1.969,1.583 false 2.667,1.313 2.531,1.313 2.531,1.313 2.448,1.552 false 1.396,0.135 1.708,0.333 0.313,0.198 10 *1 2.24,1.25 2.552,1.448 0.313,0.198 10 *2 2.708,1.229 3.021,1.427 0.313,0.198 10 *3
*1 Breather Plug Hose
*2 Breather Plug
*3 O-ring


Remove the breather plug from the breather plug hose.


c.

Remove the O-ring from the breather plug.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C136685

Remove the nut, washer and control shaft lever from the control shaft.


b.
C136686

Remove the 2 bolts and park/neutral position switch assembly from the transaxle case.

NOTICE:

Before removing the park/neutral position switch, remove any dirt or rust on the installation portion of the control shaft. Be sure to remove the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



Hide 32921C 3.REMOVE OIL COOLER TUBE UNION

a.
C278537

Using 19 mm union nut wrench, remove the 2 oil cooler tube unions from the transaxle case.


b.

Remove the 2 O-rings from the 2 oil cooler tube unions.


Hide 35104Q 4.REMOVE TRANSAXLE CASE PLUG

a.
C134959

Using a 6 mm hexagon socket wrench, remove the 3 transaxle case plugs from the transaxle housing.


b.

Remove the 3 gaskets from the 3 transaxle case plugs.


c.
C278538

Remove the 6 transaxle case plugs from the transaxle case and rear transaxle cover sub-assembly.


d.

Using a screwdriver, remove the 6 O-rings from the 6 transaxle case plugs.

NOTICE:

Be careful not to damage the transaxle case plugs.


HINT:

Tape the screwdriver tip before use.



Hide 30500 5.SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY

a.
C206507

Support the automatic transaxle assembly on wooden blocks.


Hide 35106D 6.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.

Using a 6 mm hexagon socket wrench, remove the overflow plug from the automatic transaxle oil pan sub-assembly.


b.

Remove the gasket from the overflow plug.


c.
C206508

Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.


d.
C206509

Remove the 18 bolts, automatic transaxle oil pan sub-assembly and automatic transaxle oil pan gasket from the automatic transaxle assembly.


e.

Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


Hide 35394 7.INSPECT TRANSMISSION OIL CLEANER MAGNET

Hide 35330 8.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C136687

Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.


b.
C136688C02
1.823,0.385 2.063,0.385 false 2.104,0.292 2.271,0.469 0.167,0.177 10 *1
*1 O-ring


Remove the O-ring from the valve body oil strainer assembly.


Hide 35410 9.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C136689

Remove the 11 bolts and transmission valve body assembly from the transaxle case.

NOTICE:

When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and the transaxle case to interfere with each other.



Hide 35145C 10.REMOVE TRANSAXLE CASE GASKET

a.
C274805

Remove the 2 transaxle case gaskets from the transaxle case.


Hide 35102 12.REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C206510

Remove the refill plug from the rear transaxle cover sub-assembly.


b.

Remove the gasket from the refill plug.


c.
C274806

Remove the 14 bolts from the rear transaxle cover sub-assembly.


d.

Using a brass bar and a hammer, tap on the circumference of the rear transaxle cover sub-assembly to remove the rear transaxle cover sub-assembly from the transaxle case.


e.
C274807

Remove the 3 O-rings from the transaxle case.


f.
C297890C09
1.063,1.292 0.74,0.521 0.74,0.521 0.604,0.521 false 0.729,1.542 0.542,1.115 0.542,1.115 0.406,1.115 false 0.438,0.448 0.771,0.719 0.333,0.271 10 false *1 0.219,1.042 0.5,1.406 0.281,0.365 10 false *2 2.167,1.885 2.5,2.156 0.333,0.271 10 false *1 1.792,1.885 2.073,2.25 0.281,0.365 10 false *2
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


Remove the thrust needle roller bearing and thrust needle roller race from the rear transaxle cover sub-assembly.


g.
C299131C01
1.365,0.5 1.469,0.5 1.469,0.5 1.719,0.823 true 1.958,1.302 2.219,1.823 2.219,1.823 2.083,1.823 true 1.188,0.417 1.51,0.688 0.323,0.271 10 false *1 1.906,1.75 2.229,2.021 0.323,0.271 10 false *1
*1 Oil Seal Ring


Using a screwdriver, remove the 2 oil seal rings from the rear transaxle cover sub-assembly.

NOTICE:

Be careful not to damage the rear transaxle cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



h.
C274808

Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and rear transaxle cover plate from the rear transaxle cover sub-assembly.


i.
C274809C01
1.302,0.969 1.5,0.969 false 3.094,0.438 3.406,0.594 0.313,0.156 10 *a 0.375,0.865 0.688,1.021 0.313,0.156 10 *b 1.01,0.906 1.469,1.104 0.458,0.198 10 SST
*a Turn
*b Hold


Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.

SST
09319-60020  


Hide 35635C 13.REMOVE DIRECT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C136442C01
0.844,1.313 0.844,2.094 false 2.75,0.156 3.031,0.156 3.031,0.156 2.563,1.406 false 0.781,2.115 0.948,2.281 0.167,0.167 10 *1 2.573,0.094 2.74,0.26 0.167,0.167 10 *2
*1 Direct Multiple Disc Clutch Assembly
*2 Thrust Needle Roller Bearing


Remove the direct multiple disc clutch assembly from the transaxle case.


b.

Remove the thrust needle roller bearing from the direct multiple disc clutch assembly.


Hide 35635E 14.REMOVE DIRECT MULTIPLE DISC CLUTCH SNAP RING

a.
C281630C01
2.313,1.198 2.49,0.781 2.49,0.781 2.604,0.781 false 2.635,0.698 2.948,0.854 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, remove the direct multiple disc clutch snap ring from the direct multiple disc clutch assembly.

NOTICE:

Be careful not to damage the direct multiple disc clutch assembly.


HINT:

Tape the screwdriver tip before use.



b.
C136434

Remove the No. 2 direct clutch piston from the direct multiple disc clutch assembly.


c.
C136428C01
1.615,0.25 1.281,0.25 false 1.625,1.927 1.438,1.75 1.438,1.75 1.219,1.75 false 1.125,0.188 1.292,0.365 0.167,0.177 10 *2 1.052,1.688 1.208,1.833 0.156,0.146 10 *1
*1 Intermediate Shaft Oil Seal
*2 O-ring


Using a screwdriver, remove the intermediate shaft oil seal from the direct multiple disc clutch assembly.

NOTICE:

Be careful not to damage the direct multiple disc clutch assembly.


HINT:

Tape the screwdriver tip before use.



d.

Using a screwdriver, remove the O-ring from the direct multiple disc clutch assembly.

NOTICE:

Be careful not to damage the direct multiple disc clutch assembly.


HINT:

Tape the screwdriver tip before use.



Hide 15.REMOVE NO. 2 CLUTCH DISC

a.

Remove the No. 2 clutch flange, 3 No. 2 clutch discs and 3 No. 2 clutch plates from the direct multiple disc clutch assembly.


Hide 35730 17.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

a.
C136436

Using a snap ring expander, remove the snap ring from the direct multiple disc clutch assembly.


b.
C136437

Remove the rear planetary sun gear assembly from the direct multiple disc clutch assembly.


c.
C136438C01
1.906,0.729 2.104,0.729 false 1.49,0.313 1.229,0.313 false 1.063,0.24 1.219,0.406 0.156,0.167 10 *1 2.146,0.656 2.313,0.813 0.167,0.156 10 *2
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


Remove the thrust needle roller bearing and thrust needle roller race from the direct multiple disc clutch assembly.


Hide 35730 18.INSPECT REAR PLANETARY SUN GEAR ASSEMBLY

Hide 19.REMOVE NO. 1 CLUTCH DISC

a.
C136445

Using 2 screwdrivers, remove the 2 snap rings from the direct multiple disc clutch assembly.

NOTICE:

Be careful not to damage the direct multiple disc clutch assembly.


HINT:

Tape the screwdriver tip before use.



b.

Remove the No. 1 clutch flange, 4 No. 1 clutch discs and 4 No. 1 clutch plates from the direct multiple disc clutch assembly.


Hide 35111C 21.REMOVE TRANSAXLE HOUSING

a.
C209723

Remove the 20 bolts from the transaxle housing.


b.

Using a brass bar and a hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case.


Hide 22.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE

a.
C194889N01
1.193,1.543 1.512,1.712 0.319,0.169 10 SST 0.942,1.629 1.152,1.629 false

Using SST, remove the counter driven gear front tapered roller bearing outer race and shim from the transaxle housing.

SST
09308-00010  


Hide 41311E 23.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING OUTER RACE

a.
C196810N01
0.924,0.42 1.236,0.581 0.313,0.161 10 SST 1.289,0.501 1.407,0.501 false 2.007,0.828 2.320,0.989 0.313,0.161 10 SST 2.373,0.91 2.49,0.91 false

Using SST, remove the front differential case front tapered roller bearing outer race and shim from the transaxle housing.

SST
09308-00010  


Hide 31105H 24.REMOVE TRANSAXLE CASE OIL SEAL RH (OUTER)

a.
C196824N03
0.876,1.037 1.192,1.208 0.316,0.171 10 SST 1.247,1.12 1.351,1.12 1.351,1.12 1.392,0.978 false 2.295,0.973 2.612,1.144 0.316,0.171 10 SST 2.185,1.051 2.274,1.051 false

Using SST, remove the transaxle case oil seal RH from the transaxle housing.

SST
09308-00010  


Hide 35882A 25.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C274811

Remove the bolt, clamp and differential gear lube apply tube from the transaxle housing.


Hide 26.REMOVE OIL PUMP ASSEMBLY

a.
C296578C01
2.344,0.188 2.729,0.188 false 2.771,0.094 3.083,0.292 0.313,0.198 10 false *1
*1 Gasket


Remove the 7 bolts and oil pump assembly from the transaxle case.


b.

Remove the gasket from the oil pump assembly.


c.
C293908C05
0.375,2.76 0.625,2.76 false 0.167,2.677 0.479,2.833 0.313,0.156 10 false *1
*1 Thrust Needle Roller Race


Remove the thrust needle roller race from the underdrive planetary gear assembly.


d.
C293909C04
2.135,1.25 2.521,1.25 false 0.969,0.542 1.354,0.542 false 0.771,0.438 1.083,0.635 0.313,0.198 10 false *1 2.563,1.146 2.875,1.344 0.313,0.198 10 false *2
*1 Thrust Needle Roller Bearing
*2 O-ring


Remove the thrust needle roller bearing from the counter drive gear nut.


e.

Remove the O-ring from the transaxle case.


Hide 27.REMOVE FRONT OIL PUMP BODY O-RING

a.
C293910

Remove the O-ring from the front oil pump body sub-assembly.


Hide 35683B 28.REMOVE NO. 3 BRAKE DISC

a.
C136451C02
1.135,0.781 0.938,0.469 0.938,0.469 0.635,0.469 true 0.479,0.406 0.646,0.563 0.167,0.156 10 false *1
*1 Snap Ring


Using a screwdriver, remove the snap ring from the oil pump assembly.

NOTICE:

Be careful not to damage the oil pump assembly.


HINT:

Tape the screwdriver tip before use.



b.

Remove the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates from the oil pump assembly.


Hide 34330 30.REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C136458

Remove the underdrive planetary gear assembly from the oil pump assembly.


Hide 35663 31.REMOVE NO. 3 BRAKE HUB

a.
C136454

Remove the No. 3 brake hub from the underdrive planetary gear assembly.


b.
C136455C01
1.479,0.313 1.25,0.313 false 1.927,0.906 2.146,0.906 false 2.198,0.833 2.365,0.99 0.167,0.156 10 *2 1.083,0.24 1.24,0.396 0.156,0.156 10 *1
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing


Remove the thrust needle roller bearing and thrust needle roller race from the underdrive planetary gear assembly.


Hide 34341 32.REMOVE UNDERDRIVE PLANETARY RING GEAR

a.
C136456C01
2.083,0.438 2.365,0.438 false 1.323,0.813 1,0.813 false 2.396,0.365 2.552,0.552 0.156,0.188 10 *1 0.833,0.75 0.99,0.906 0.156,0.156 10 *2
*1 Snap Ring
*2 Underdrive Planetary Ring Gear


Using needle-nose pliers, remove the snap ring from the underdrive planetary ring gear.


b.

Remove the underdrive planetary ring gear from the underdrive planetary gear assembly.


Hide 35706V 33.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C136457C01
1.427,2.948 1.094,2.948 false 1.198,0.458 1.396,0.458 false 2.49,1.719 2.198,1.719 false 0.917,2.875 1.094,3.021 0.177,0.146 10 *3 1.031,0.385 1.198,0.531 0.167,0.146 10 *1 2.531,1.635 2.719,1.792 0.188,0.156 10 *2
*1 Planetary Sun Gear Sub-assembly
*2 Underdrive Planetary Gear Assembly
*3 Snap Ring


While expanding the snap ring with snap ring pliers, remove the planetary sun gear sub-assembly from the underdrive planetary gear assembly.


b.

Remove the snap ring from the underdrive planetary gear assembly.


Hide 34330 34.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY

Hide 35706V 35.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

Hide 35701 36.REMOVE INPUT SHAFT SUB-ASSEMBLY

a.
C136459

Remove the input shaft sub-assembly from the oil pump assembly.


b.
C136460C01
1.406,0.229 1.167,0.229 false 2.167,0.729 1.917,0.729 false 1.833,2.729 2.417,2.542 2.417,2.542 1.844,3.052 false 1.844,2.896 2.417,2.542 false 0.969,1.833 1.5,1.833 false 2.219,0.646 2.385,0.802 0.167,0.156 10 *2 0.99,0.156 1.146,0.313 0.156,0.156 10 *1 0.792,1.76 0.948,1.906 0.156,0.146 10 *4 2.469,2.458 2.625,2.615 0.156,0.156 10 *3
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing
*3 Input Shaft Oil Seal Ring
*4 Input Shaft


Remove the thrust needle roller bearing and thrust needle roller race from the input shaft sub-assembly.


c.

Using a screwdriver, remove the 3 input shaft oil seal rings from the input shaft sub-assembly.

NOTICE:

Be careful not to damage the input shaft.


HINT:

Tape the screwdriver tip before use.



Hide 34321 37.REMOVE UNDERDRIVE PLANETARY SUN GEAR

a.
C136461C01
1,0.615 1.375,0.615 false 2.292,1.292 2,1.292 false 2.333,1.219 2.5,1.385 0.167,0.167 10 *2 0.833,0.552 0.99,0.698 0.156,0.146 10 *1
*1 Underdrive Planetary Sun Gear
*2 Thrust Needle Roller Bearing


Remove the underdrive planetary sun gear from the oil pump assembly.


b.

Remove the thrust needle roller bearing from the oil pump assembly.


Hide 38.REMOVE NO. 1 BRAKE DISC

a.
C153477C02
2.188,0.583 2.479,0.583 false 2.188,1.177 2.323,1.177 2.323,1.177 2.323,0.583 false 1.24,0.885 1.042,0.885 false 2.521,0.51 2.688,0.667 0.167,0.156 10 *1 0.875,0.813 1.042,0.969 0.167,0.156 10 *2
*1 Snap Ring
*2 Brake Snap Ring Stopper


Using a screwdriver, remove the 2 snap rings and brake snap ring stopper from the oil pump assembly.

NOTICE:

Be careful not to damage the oil pump assembly.


HINT:

Tape the screwdriver tip before use.



b.

Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the oil pump assembly.


Hide 35608L 40.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C136464

Remove the 3 2nd brake piston return springs from the oil pump assembly.


Hide 35608L 41.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35621F 42.REMOVE NO. 1 BRAKE PISTON

a.
C136465

Holding the oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump assembly to remove the No. 1 brake piston.


b.
C136466C01
1.979,0.677 2.375,0.677 false 1.354,0.677 0.906,0.677 false 2.427,0.583 2.573,0.74 0.146,0.156 10 *1 0.729,0.594 0.885,0.75 0.156,0.156 10 *1
*1 O-ring


Using a screwdriver, remove the 2 O-rings from the No. 1 brake piston.

NOTICE:

Be careful not to damage the No. 1 brake piston.


HINT:

Tape the screwdriver tip before use.



Hide 41311 43.REMOVE FRONT DIFFERENTIAL CASE

a.
C196803

Remove the front differential case from the transaxle case.


Hide 41311E 44.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING INNER RACE

a.
C205371C05
1.229,1.563 0.469,1.74 0.469,1.74 1.063,0.625 true 1.458,1.104 0.49,1.719 0.49,1.719 1.458,1.042 true 2.635,0.146 2.792,0.344 0.156,0.198 10 false *a 0.24,0.333 0.396,0.531 0.156,0.198 10 false *b 0.146,1.729 0.604,1.927 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the front differential case front tapered roller bearing inner race from the front differential case.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00480)


Hide 41311F 45.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING INNER RACE

a.
C317736C03
0.729,1.219 0.396,0.313 0.396,0.313 0.615,0.604 true 1.417,0.146 1.729,0.354 0.313,0.208 10 false *a 0.052,0.76 0.313,1 0.26,0.24 10 false *b 0.104,0.177 0.49,0.427 0.385,0.25 10 false SST
*a Turn
*b Hold


Using SST, remove the front differential case rear tapered roller bearing inner race from the front differential case.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00480)


Hide 35782H 46.REMOVE COUNTER DRIVE GEAR NUT

a.
C136698N01
1.552,0.688 1.167,0.427 false 0.875,0.354 1.219,0.542 0.344,0.188 10 SST

Using SST and a hammer, unstake the counter drive gear nut.

SST
09930-00010  


b.
C136700N01
1.5,4.063 1.656,4.24 0.156,0.177 10 P

Turn the manual valve lever 2 notches counterclockwise to set it to P as shown in the illustration.


c.
C136468N01
1.604,1.417 0.688,0.292 false 0.385,0.188 0.708,0.354 0.323,0.167 10 SST

Using SST, remove the counter drive gear nut from the front planetary gear assembly.

SST
09387-00130  


Hide 35783R 47.REMOVE COUNTER DRIVEN GEAR

a.
C136699N01
1.525,3.957 1.769,4.122 0.244,0.165 10 N

Turn the manual valve lever 2 notches clockwise to set it to N as shown in the illustration.


b.
C136469

Remove the counter driven gear from the transaxle case.


Hide 48.REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING

a.
C194890C01
1.438,0.594 1.583,0.74 1.583,0.74 1.438,1.219 false 1.583,0.74 1.063,1.188 false 2.219,0.49 2.875,0.219 2.875,0.219 2.771,0.667 false 1.604,0.052 1.771,0.24 0.167,0.188 10 *a 0.094,0.667 0.26,0.854 0.167,0.188 10 *b 1.615,0.656 2.021,0.823 0.406,0.167 10 SST 2.906,0.115 3.271,0.281 0.365,0.167 10 SST
*a Turn
*b Hold


Using SST, remove the counter driven gear front tapered roller bearing from the counter driven gear.

SST
09950-00020  
09950-00030  
09950-60010  (09951-00400)


Hide 49.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING

a.
C194891C01
0.531,0.729 0.219,1.563 0.219,1.563 0.573,1.49 false 0.229,1.552 0.865,1.354 false 2.26,1.292 2.042,1.604 false 2.885,0.385 2.813,0.385 2.813,0.385 2.688,1.104 false 1.573,0.052 1.74,0.229 0.167,0.177 10 *a 0.073,0.604 0.292,0.792 0.219,0.188 10 *b 0.031,1.573 0.354,1.74 0.323,0.167 10 SST 2.927,0.313 3.313,0.479 0.385,0.167 10 SST 1.885,1.625 2.292,1.792 0.406,0.167 10 SST
*a Turn
*b Hold


Using SST, remove the counter driven gear rear tapered roller bearing from the counter driven gear.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)
09950-60010  (09951-00320)


Hide 35558 50.REMOVE PAWL SHAFT CLAMP

a.
C136472

Remove the bolt and pawl shaft clamp from the transaxle case.


Hide 35596 51.REMOVE PAWL STOPPER PLATE

a.
C136473

Remove the 2 bolts and pawl stopper plate from the transaxle case.


Hide 35598 52.REMOVE PARKING LOCK SLEEVE

a.
C136474

Remove the parking lock sleeve from the transaxle case.


Hide 35557 53.REMOVE PARKING LOCK PAWL

a.
C136475C01
0.896,0.469 1.063,0.469 1.063,0.469 1.156,1.302 false 0.26,0.385 0.406,0.385 0.406,0.385 0.479,1.625 false 0.375,2.823 0.375,2.708 0.375,2.708 1.031,2.469 false 1.458,2.708 0.854,3.021 0.854,3.021 0.854,3.146 false 0.313,2.844 0.49,3.021 0.177,0.177 10 *3 0.792,3.167 0.958,3.333 0.167,0.167 10 *4 0.094,0.313 0.26,0.479 0.167,0.167 10 *1 0.729,0.385 0.906,0.531 0.177,0.146 10 *2
*1 Parking Lock Pawl Shaft
*2 Parking Lock Pawl
*3 Spring
*4 Parking Lock Pawl Pin


Remove the spring, parking lock pawl pin, parking lock pawl shaft and parking lock pawl from the transaxle case.


Hide 54.REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE

a.
C194892N05
0.604,0.594 0.833,0.594 false 1.885,0.594 2.313,0.594 false 0.281,0.531 0.604,0.698 0.323,0.167 10 SST 1.563,0.521 1.885,0.688 0.323,0.167 10 SST

Using SST, remove the counter driven gear rear tapered roller bearing outer race from the transaxle case.

SST
09308-00010  


Hide 41311F 55.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING OUTER RACE

a.
C196814N07
0.248,0.361 0.566,0.545 0.318,0.184 10 SST 0.614,0.444 0.781,0.444 false 2.699,1.409 3.017,1.593 0.318,0.184 10 SST 2.859,1.178 2.859,1.393 false

Using SST, remove the front differential case rear tapered roller bearing outer race from the transaxle case.

SST
09308-00010  


Hide 31105H 56.REMOVE TRANSAXLE CASE OIL SEAL LH

a.
C138709N07
1.406,0.948 0.573,0.333 0.573,0.333 1.271,1.427 true 0.271,0.25 0.594,0.438 0.323,0.188 10 SST

Using SST, and a hammer, tap out the transaxle case oil seal LH from the transaxle case.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07100)


Hide 35790 57.REMOVE ONE-WAY CLUTCH ASSEMBLY

a.
C281634C01
1.885,0.302 2.052,0.302 2.052,0.302 2.292,1.177 true 1.698,0.219 2.01,0.375 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.



b.
C141526C02
1.76,1 2.302,1 false 0.792,0.302 1.24,0.302 false 2.354,0.938 2.521,1.094 0.167,0.156 10 *2 0.625,0.24 0.781,0.385 0.156,0.146 10 *1
*1 One-way Clutch Assembly
*2 Thrust Needle Roller Bearing


Remove the one-way clutch assembly with the planetary ring gear from the transaxle case.


c.

Remove the thrust needle roller bearing from the planetary gear assembly.


Hide 35743K 59.REMOVE PLANETARY RING GEAR

a.
C201345C07
0.917,0.094 1.01,0.094 1.01,0.094 1.313,0.375 false 1.135,1.417 1.396,1.417 false 2.521,0.979 2.802,1.052 2.802,1.052 2.802,1.135 false 0.74,0.031 0.896,0.219 0.156,0.188 10 false *1 0.969,1.344 1.135,1.521 0.167,0.177 10 false *3 2.698,1.146 2.885,1.344 0.188,0.198 10 false *2
*1 One-way Clutch Assembly
*2 Outer Race Retainer
*3 Planetary Ring Gear


Remove the planetary ring gear from the one-way clutch assembly.


b.

Remove the outer race retainer from the one-way clutch assembly.


Hide 35762E 60.REMOVE PLANETARY RING GEAR FLANGE

a.
C136480C02
1.26,0.656 0.958,0.656 false 0.948,2.302 1.208,2.302 false 2.115,1.354 2.427,1.354 false 0.781,2.219 0.958,2.385 0.177,0.167 10 *3 2.469,1.271 2.635,1.427 0.167,0.156 10 *2 0.771,0.583 0.948,0.75 0.177,0.167 10 *1
*1 Snap Ring
*2 Planetary Ring Gear Flange
*3 Planetary Ring Gear


Using a screwdriver, remove the snap ring from the planetary ring gear.

NOTICE:

Be careful not to damage the planetary ring gear.


HINT:

Tape the screwdriver tip before use.



b.

Remove the planetary ring gear flange from the planetary ring gear.


Hide 35682A 61.REMOVE NO. 2 BRAKE DISC

a.
C281633C01
2.125,1.146 1.917,0.302 1.917,0.302 1.74,0.302 true 1.573,0.229 1.885,0.385 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.



b.

Remove the No. 2 brake flange, 5 No. 2 brake discs and 5 No. 2 brake plates from the transaxle case.


Hide 35068C 63.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C281631C01
2.135,1.135 1.885,0.302 1.885,0.302 1.698,0.302 true 1.531,0.229 1.844,0.385 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, remove the snap ring from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.



b.
C136484

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case.


Hide 35068C 64.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 35622G 65.REMOVE NO. 2 BRAKE PISTON

a.
C136485

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the ATF hole to remove the No. 2 brake piston from the transaxle case.


b.
C136673C01
1.979,0.51 2.563,0.51 false 1.344,1.208 0.885,1.208 false 0.729,1.135 0.885,1.323 0.156,0.188 10 *1 2.615,0.427 2.771,0.615 0.156,0.188 10 *1
*1 O-ring


Using a screwdriver, remove the 2 O-rings from the No. 2 brake piston.

NOTICE:

Be careful not to damage the No. 2 brake piston.


HINT:

Tape the screwdriver tip before use.



Hide 35720 66.REMOVE FRONT PLANETARY GEAR ASSEMBLY

a.
C136674N06
1.771,1.719 2.594,1.302 2.594,1.302 1.906,1.958 true 2.635,1.198 2.979,1.365 0.344,0.167 10 SST

Using SST and a press, remove the front planetary gear assembly from the transaxle case.

SST
09950-60010  (09951-00580)
09950-70010  (09951-07100)


Hide 35782C 67.REMOVE COUNTER DRIVE GEAR

NOTICE:

Perform this procedure only when the counter drive gear bearing or transaxle case is replaced.


a.
C274813N02
1.302,1.323 0.677,0.531 0.677,0.531 1.406,1.177 true 0.927,3.042 1.219,3.042 1.219,3.042 1.021,3.24 false 0.406,0.396 0.865,0.594 0.458,0.198 10 SST 1.271,2.948 1.729,3.146 0.458,0.198 10 SST

Using SST and a press, remove the counter drive gear and bearing inner race (rear side) from the transaxle case.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)


b.
C136676

As shown in the illustration, tighten the 3 bolts evenly and leave a clearance of approximately 20.0 mm (0.787 in.) between the counter drive gear and bearing inner race (front side).


c.
C194894C02
0.479,1.5 0.396,1.656 0.396,1.656 0.885,1.479 true 2.344,0.802 2.438,0.802 2.438,0.802 2.26,1.229 false 2.875,0.844 2.771,1.156 false 1.625,0.073 1.792,0.229 0.167,0.156 10 *a 0.063,0.698 0.24,0.885 0.177,0.188 10 *b 0.104,1.604 0.5,1.771 0.396,0.167 10 SST 2.896,0.708 3.292,0.875 0.396,0.167 10 SST 2,0.729 2.396,0.896 0.396,0.167 10 SST
*a Turn
*b Hold


Using SST, remove the bearing inner race (front side) from the counter drive gear.

SST
09950-00020  
09950-00030  
09950-60020  (09951-00710)


Hide 35623 68.REMOVE NO. 3 BRAKE PISTON

a.
C136678

Using a screwdriver, remove the snap ring from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.



b.
C136679C01
1.01,0.51 1.115,0.51 1.115,0.51 1.458,0.885 false 2.281,0.313 2.031,0.313 false 0.813,0.427 0.969,0.583 0.156,0.156 10 *2 2.313,0.229 2.469,0.385 0.156,0.156 10 *1
*1 Brake Piston Return Spring
*2 No. 3 Brake Piston


Remove the brake piston return spring from the transaxle case.


c.

Remove the No. 3 brake piston from the transaxle case.


Hide 35409 69.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C201354

Remove the bolt, cover and manual detent spring sub-assembly from the transaxle case.


Hide 35501 70.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

a.
C201355C01
0.771,1.51 0.896,1.51 0.896,1.51 1.698,1.219 true 2.052,0.75 2.458,0.146 2.458,0.146 2.604,0.146 true 0.604,1.427 0.917,1.583 0.313,0.156 10 false *1 2.656,0.063 2.969,0.219 0.313,0.156 10 false *2
*1 Parking Lock Rod Sub-assembly
*2 Manual Valve Lever Sub-assembly


Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.

HINT:

Align the slot with the notches on the manual valve lever sub-assembly to remove the parking lock rod sub-assembly.



Hide 35506 71.REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C201356

Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the transaxle case.


b.
C201357

Remove the manual valve lever shaft sub-assembly from the transaxle case.


Hide 35506F 72.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C281632C01
1.146,0.313 1.281,0.313 1.281,0.313 1.51,1.083 true 0.979,0.229 1.292,0.385 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case.

NOTICE:

Be careful not to damage the transaxle case.


HINT:

Tape the screwdriver tip before use.