Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for LH Side) › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008433 SEAT _0049737 REAR SEAT ASSEMBLY(for LH Side) A

SEAT  REAR SEAT ASSEMBLY(for LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart.


Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS

PROCEDURE

Hide 71078S 1.INSTALL SEPARATE TYPE REAR SEATBACK COVER

a.
B340941C01
1.771,1.49 2.104,0.406 2.104,0.406 2.406,0.406 false 2.469,0.281 2.781,0.438 0.313,0.156 10 *1
*1 Hog Ring Pliers


Set the separate type rear seatback cover in place.


b.

Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 11 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




c.
B340942C01
1.813,1.49 2.031,0.417 2.031,0.417 2.406,0.417 false 2.458,0.313 2.771,0.469 0.313,0.156 10 *1
*1 Hog Ring Pliers


Using hog ring pliers, install 5 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




d.

Install the separate type rear seatback cover (with pad) to the rear seatback frame sub-assembly LH.


e.

Attach the 9 clamps.


f.

Attach the 8 claws to install the 4 rear seat headrest supports.


Hide 71882A 2.INSTALL REAR SEATBACK BOARD LH

a.

Attach the clamp and 7 claws to install the rear seatback board LH.


b.
B340946
1.823,1.521 2.021,0.396 2.021,0.396 2.344,0.396 false 2.396,0.313 2.708,0.469 0.313,0.156 10 *1
*1 Hog Ring Pliers


Using hog ring pliers, install 6 new hog rings and attach the 2 pieces of fastening tape.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




Hide 3.INSTALL REAR NO. 1 SEATBACK ASSEMBLY LH

a.

Install the rear No. 1 seatback assembly LH to the rear seat reclining adjuster assembly LH with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73380D 4.INSTALL REAR SEAT INNER BELT ASSEMBLY LH

a.

Install the rear seat inner belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 72380 5.INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY

a.
B341755
0.229,0.51 0.385,0.708 0.156,0.198 10 1 1.01,0.792 1.167,0.99 0.156,0.198 10 2 3.219,2.51 3.375,2.708 0.156,0.198 10 1 2.656,2.813 2.813,3.01 0.156,0.198 10 2

Install the No. 2 seat adjuster control cable assembly in the order shown in the illustration.


b.

Attach the 2 clamps of the cable ends.


c.

Attach the 4 clamps.


Hide 71829B 6.INSTALL REAR SEAT REAR CUSHION MOULDING LH

a.

Attach the clamp and claw to install the rear seat rear cushion moulding LH.


b.

w/ Seat Belt Warning System:

Attach the 2 clamps.


Hide 72997 7.INSTALL REAR SEATBACK COVER LH

a.

Attach the claw to install the rear seatback cover LH.


b.

Install the clip and screw.


Hide 72998C 8.INSTALL REAR SEAT COVER LH

a.

Attach the claw to install the rear seat cover LH.


b.

Install the clip and screw.


Hide 71826B 9.INSTALL REAR SEAT CUSHION MOULDING LH

a.

Attach the 3 hooks and claw to install the rear seat cushion moulding LH.


Hide 71076S 10.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.
B340943C01
1.844,1.479 2.031,0.427 2.031,0.427 2.375,0.427 false 2.448,0.292 2.76,0.448 0.313,0.156 10 *1
*1 Hog Ring Pliers


Set the separate type rear seat cushion cover in place.


b.

Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad LH with 13 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




c.
B340944
1.854,1.479 2.063,0.396 2.063,0.396 2.458,0.396 false 2.51,0.26 2.823,0.417 0.313,0.156 10 *1
*1 Hog Ring Pliers


Using hog ring pliers, install 5 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




d.

Install the separate type rear seat cushion cover (with pad) to the rear seat spring assembly with the 20 hooks.


Hide 11.INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY LH

a.

Install the rear No. 1 seat cushion assembly LH with the 2 bushes and 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the 2 claws to install the rear seatback cover.


c.

Install the 3 clamps.


d.
B341756
0.448,1.135 0.604,1.333 0.156,0.198 10 1 0.833,0.594 0.99,0.792 0.156,0.198 10 2

Connect the cable in the order shown in the illustration.


e.

Attach the clamp of the cable end.


f.

Install the 2 bushes and 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72526A 12.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.

Install the reclining adjuster release handle LH with the 3 screws.


Hide 71846B 13.INSTALL REAR SEATBACK NO. 1 BOARD CAP

a.

Attach the 3 claws to install the rear seatback No. 1 board cap.


Hide 72831B 14.INSTALL REAR SEAT NO. 1 CENTER ARMREST PLATE

a.

Install the rear seat No. 1 center armrest plate.


Hide 72830 15.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

a.

Install the rear seat center armrest assembly with the washer and bolt.


Hide 71694 16.INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH

a.

Attach the clamp and 4 claws to install the rear seat lower cushion hinge cover LH.


Hide 71693A 17.INSTALL REAR SEAT NO. 3 CUSHION HINGE COVER

a.

Attach the clamp and 4 claws to install the rear seat No. 3 cushion hinge cover.


b.

Attach the clamp.


Hide 72868 18.INSTALL CENTER ARMREST HINGE COVER RH

a.

Attach the clamp to install the center armrest hinge cover RH.


Hide 73340C 19.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY LH

Hide 71960B 20.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY

Hide 71940A 21.INSTALL REAR SEAT HEADREST ASSEMBLY