Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/o Occupant Classification System)
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0049192 AIRBAG SYSTEM(w/o Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o Occupant Classification System)  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  


DESCRIPTION

The circuit for the side collision sensor LH or RH (to determine deployment of the curtain shield airbag assembly LH or RH) is composed of the airbag sensor assembly, door side airbag sensor LH or RH and rear airbag sensor LH or RH.

The rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1633/81 or B1638/82 is stored when a malfunction is detected in the circuit for the rear side collision sensor LH or RH (to determine deployment of the curtain shield airbag assembly LH or RH).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the rear side collision sensor RH (to determine deployment of the curtain shield airbag assembly RH) for 2 seconds.

·

A rear airbag sensor RH malfunction.

·

A airbag sensor assembly malfunction.


·

Floor wire

·

Rear airbag sensor RH

·

Airbag sensor assembly


B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the rear side collision sensor LH (to determine deployment of the curtain shield airbag assembly LH) for 2 seconds.

·

A rear airbag sensor LH malfunction.

·

A airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Rear airbag sensor LH

·

Airbag sensor assembly



WIRING DIAGRAM

C279110E01
0.052,0.052 1.406,0.385 1.354,0.333 12 false for RH Side: 1.083,0.656 1.531,0.844 0.448,0.188 10 false BCR+ 1.094,1.052 1.51,1.24 0.417,0.188 10 false BCR- 1.094,1.833 1.531,2.021 0.438,0.188 10 false BDR+ 1.094,2.26 1.521,2.438 0.427,0.177 10 false BDR- 2.281,1.833 2.615,2.042 0.333,0.208 10 false IM1 3.115,1.823 3.573,2.01 0.458,0.188 10 false BDR+ 3.125,2.271 3.583,2.458 0.458,0.188 10 false BDR- 5.667,0.635 6.125,0.823 0.458,0.188 10 false BBR+ 5.677,1.073 6.135,1.26 0.458,0.188 10 false BBR- 5.313,2.021 6.958,2.219 1.646,0.198 10 false Airbag Sensor Assembly 0.302,2.844 1.875,3.052 1.573,0.208 10 false Rear Airbag Sensor RH 5.333,1.885 5.792,2.073 0.458,0.188 10 false M24 3.042,2.76 3.396,2.969 0.354,0.208 10 false I13 0.302,2.677 0.563,2.875 0.26,0.198 10 false M7 1.552,0.552 1.771,0.729 0.219,0.177 10 false 4 1.552,0.969 1.74,1.156 0.188,0.188 10 false 3 1.531,1.75 1.708,1.927 0.177,0.177 10 false 1 1.552,2.177 1.75,2.365 0.198,0.188 10 false 2 5.49,0.563 5.708,0.75 0.219,0.188 10 false 8 5.438,0.979 5.677,1.167 0.24,0.188 10 false 15 2.292,2.25 2.625,2.458 0.333,0.208 10 false IM1 2.354,2.083 2.531,2.26 0.177,0.177 10 false 1 2.344,1.667 2.542,1.854 0.198,0.188 10 false 2 2.948,1.74 3.146,1.927 0.198,0.188 10 false 2 2.948,2.177 3.125,2.354 0.177,0.177 10 false 1 3.01,2.917 4.854,3.125 1.844,0.208 10 false Door Side Airbag Sensor RH

C279110E02
0.052,0.052 1.208,0.365 1.156,0.313 12 false for LH Side: 1.083,0.656 1.531,0.844 0.448,0.188 10 false BCL+ 1.094,1.052 1.51,1.24 0.417,0.188 10 false BCL- 1.094,1.833 1.531,2.021 0.438,0.188 10 false BDL+ 1.094,2.26 1.521,2.438 0.427,0.177 10 false BDL- 2.281,1.844 2.615,2.052 0.333,0.208 10 false JN1 3.115,1.823 3.573,2.01 0.458,0.188 10 false BDL+ 3.125,2.271 3.583,2.458 0.458,0.188 10 false BDL- 5.667,0.635 6.125,0.823 0.458,0.188 10 false BBL+ 5.677,1.073 6.135,1.26 0.458,0.188 10 false BBL- 5.385,2.052 7.156,2.26 1.771,0.208 10 false Airbag Sensor Assembly 0.302,2.844 1.875,3.052 1.573,0.208 10 false Rear Airbag Sensor LH 5.396,1.927 5.854,2.115 0.458,0.188 10 false N20 3.042,2.708 3.396,2.917 0.354,0.208 10 false J12 0.302,2.677 0.563,2.875 0.26,0.198 10 false N9 1.552,0.552 1.771,0.729 0.219,0.177 10 false 4 1.552,0.969 1.74,1.156 0.188,0.188 10 false 3 1.531,1.75 1.708,1.927 0.177,0.177 10 false 1 1.552,2.177 1.75,2.365 0.198,0.188 10 false 2 5.49,0.573 5.708,0.76 0.219,0.188 10 false 8 5.438,0.979 5.677,1.167 0.24,0.188 10 false 11 2.292,2.26 2.625,2.469 0.333,0.208 10 false JN1 2.354,2.083 2.531,2.26 0.177,0.177 10 false 1 2.344,1.667 2.542,1.854 0.198,0.188 10 false 3 2.948,1.74 3.146,1.927 0.198,0.188 10 false 2 2.948,2.177 3.125,2.354 0.177,0.177 10 false 1 3.01,2.844 4.885,3.052 1.875,0.208 10 false Door Side Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK PAST DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188

Result:
Proceed to
DTC B1632/81 and B1637/82 are not output
DTC B1632/81 and B1637/82 are output



DTC B1632/81 and B1637/82 are not output

2.CHECK DTC

DTC B1632/81 and B1637/82 are output

2.CHECK DTC
a.

Turn the ignition switch to ON.

HINT:

If a communication error occurs, DTCs for both the LH and RH sides will be stored simultaneously. The malfunctioning area can be identified by turning the ignition switch off and then to ON again.



b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1633/81 is output
DTC B1638/82 is output
DTC B1633/81 and B1638/82 are not output


HINT:

Codes other than DTC B1633/81 and B1638/82 may be output at this time, but they are not related to this check.




DTC B1633/81 is output

3.CHECK CONNECTION OF CONNECTORS

DTC B1638/82 is output

7.CHECK CONNECTION OF CONNECTORS

DTC B1633/81 and B1638/82 are not output

3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and rear airbag sensor RH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

4.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and rear airbag sensor RH.


b.
C215710C01
0.625,1.427 0.938,1.583 0.313,0.156 10 *1 2.531,1.563 2.844,1.719 0.313,0.156 10 *2 1.49,1.104 1.802,1.26 0.313,0.156 10 *3
*1 Rear Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and rear airbag sensor RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

5.CHECK REAR AIRBAG SENSOR RH CIRCUIT

The connectors are deformed or damaged

REPLACE FLOOR WIRE

5.CHECK REAR AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C279113C01
2.771,0.677 3.104,0.896 0.333,0.219 4.927,0.698 5.26,0.917 0.333,0.219 3.417,1.281 3.917,0.875 false 4.26,1.281 4.01,0.854 false 6.813,1.385 6.146,0.958 false 5.198,1.198 5.427,1.073 false 5.604,1.448 5.823,1.177 false 0.469,1.104 0.781,1.26 0.313,0.156 10 *1 1.969,1.177 2.281,1.333 0.313,0.156 10 *2 1.177,0.469 1.49,0.625 0.313,0.156 10 *3 4.448,0.688 4.76,0.844 0.313,0.156 10 *4 6.813,0.646 7.125,0.802 0.313,0.156 10 *5 5.042,1.167 5.354,1.323 0.313,0.156 10 *6 3.74,0.177 4.052,0.333 0.313,0.156 10 *a 6.052,0.104 6.365,0.26 0.313,0.156 10 *b 0.552,0.667 0.729,0.844 0.177,0.177 10 D 0.958,0.896 1.135,1.073 0.177,0.177 10 C 1.458,0.896 1.635,1.073 0.177,0.177 10 B 1.833,0.646 2.01,0.823 0.177,0.177 10 A 2.844,0.698 3.156,0.854 0.313,0.156 10 M7 3.271,1.333 3.802,1.594 0.531,0.26 10 BCR- 4.167,1.323 4.708,1.521 0.542,0.198 10 BCR+ 6.667,1.438 7.125,1.646 0.458,0.208 10 BBR+ 5.323,1.51 5.771,1.698 0.448,0.188 10 BBR- 4.958,0.719 5.271,0.875 0.313,0.156 10 M24
*1 Rear Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M7-4 (BCR+) - Body ground Ignition switch ON Below 1 V
M7-3 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBR+) and 15 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-4 (BCR+) - M7-3 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M7-4 (BCR+) - M7-3 (BCR-) Always 1 MΩ or higher
M7-4 (BCR+) - Body ground Always 1 MΩ or higher
M7-3 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK REAR AIRBAG SENSOR RH

NG

REPLACE FLOOR WIRE

6.CHECK REAR AIRBAG SENSOR RH
a.
C157773C01
0.711,1.256 0.899,1.431 0.189,0.175 10 *1 1.756,1.356 1.945,1.531 0.189,0.175 10 *2
*1 Rear Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the rear airbag sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1638/82 is output
DTC B1633/81 is output
DTC B1633/81 and B1638/82 are not output


HINT:

Codes other than DTC B1633/81 and B1638/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B1638/82 is output

DTC B1633/81 is output

DTC B1633/81 and B1638/82 are not output

7.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and rear airbag sensor LH.

Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected




The connectors are properly connected

8.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

8.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and rear airbag sensor LH.


b.
C208245C06
0.313,1.75 0.625,1.906 0.313,0.156 10 *1 2.104,1.573 2.417,1.729 0.313,0.156 10 *2 1.521,1.042 1.833,1.198 0.313,0.156 10 *3
*1 Rear Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire


Check that the connectors (on the airbag sensor assembly side and rear airbag sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

9.CHECK REAR AIRBAG SENSOR LH CIRCUIT

The connectors are deformed or damaged

REPLACE NO. 2 FLOOR WIRE

9.CHECK REAR AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C279114C01
2.865,0.656 3.25,0.875 0.385,0.219 5,0.635 5.385,0.854 0.385,0.219 3.594,1.198 4.01,0.781 false 4.406,1.188 4.146,0.781 false 6.51,1.479 6.385,1.115 false 5.448,1.385 6.083,0.917 false 6.865,1.281 6.615,0.948 false 0.563,1.271 0.875,1.427 0.313,0.156 10 *1 2.052,1.156 2.365,1.313 0.313,0.156 10 *2 1.25,0.635 1.563,0.792 0.313,0.156 10 *3 4.604,0.615 4.917,0.771 0.313,0.156 10 *4 6.813,0.688 7.125,0.844 0.313,0.156 10 *5 6.875,1.156 7.135,1.354 0.26,0.198 10 *6 3.875,0.135 4.188,0.292 0.313,0.156 10 *a 5.958,0.094 6.271,0.25 0.313,0.156 10 *b 0.656,0.833 0.875,1.021 0.219,0.188 10 D 1.031,1.063 1.25,1.25 0.219,0.188 10 C 1.542,1.063 1.76,1.25 0.219,0.188 10 B 1.917,0.833 2.135,1.021 0.219,0.188 10 A 2.958,0.688 3.271,0.844 0.313,0.156 10 N9 5.083,0.667 5.396,0.823 0.313,0.156 10 N20 3.354,1.229 3.813,1.427 0.458,0.198 10 BCL- 4.281,1.229 4.74,1.427 0.458,0.198 10 BCL+ 5.156,1.417 5.615,1.615 0.458,0.198 10 BBL+ 6.427,1.5 6.885,1.698 0.458,0.198 10 BBL-
*1 Rear Airbag Sensor LH *2 Airbag Sensor Assembly
*3 No. 2 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N9-4 (BCL+) - Body ground Ignition switch ON Below 1 V
N9-3 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBL+) and 11 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N9-4 (BCL+) - N9-3 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N9-4 (BCL+) - N9-3 (BCL-) Always 1 MΩ or higher
N9-4 (BCL+) - Body ground Always 1 MΩ or higher
N9-3 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK REAR AIRBAG SENSOR LH

NG

REPLACE NO. 2 FLOOR WIRE

10.CHECK REAR AIRBAG SENSOR LH
a.
C171812C15
0.698,1.281 0.854,1.448 0.156,0.167 10 *1 1.813,1.125 2,1.292 0.188,0.167 10 *2
*1 Rear Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the rear airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1633/81 is output
DTC B1638/82 is output
DTC B1633/81 and B1638/82 are not output


HINT:

Codes other than DTC B1633/81 and B1638/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.



DTC B1633/81 is output

DTC B1638/82 is output

DTC B1633/81 and B1638/82 are not output