Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0046807 ECD SYSTEM(for DPF) J

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  Rough Idling or Excessive Engine Vibrations  


DESCRIPTION

Malfunction Condition Main Trouble Area Related Trouble Area
·

Rough idling or juddering due to abnormal combustion

·

Juddering when vehicle is starting due to clutch system malfunctions


1.

Injector assembly malfunctions

·

Injector sliding malfunction

·

Injector stuck closed

·

Injector stuck open

·

Deposits in injector

·

Injector circuit malfunction


2.

Clutch system malfunctions

·

Clutch system (juddering when starting)



·

Injector compensation code

·

Fuel leak

·

Engine mounting

·

Intake air system leakage

·

Intake air system blockage

·

EGR system

·

Throttle valve system

·

Mass air flow meter assembly

·

Suction control valve

·

Fuel pressure sensor built into common rail assembly

·

Injector driver (EDU) (P062D stored simultaneously)

·

Low quality fuel

·

Vehicle modifications

·

Fuel filter air bleed problem

·

Accessory problem (A/C, generator, etc.)

·

ECM



HINT:
·

This troubleshooting procedure checks for the cause of rough idling and excessive engine vibrations.

·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List result values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.



Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Mass Air Flow Meter Assembly
Main fault Decrease in performance (foreign matter is stuck)
Symptoms Lack of power, black smoke
Data List MAF
HINT:

The maximum fuel injection volume is controlled according to the output from the mass air flow meter assembly.



Glow System
Main fault Glow system malfunction
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Data List Check the glow plug indicator light
Diagnostic Point Measure the resistance of the glow plug assembly

Engine
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.




b.

Common Rail (ALL)

Supply Pump Assembly
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
·

Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:
·

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

·

When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.



Diagnostic Trouble Code Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

Fuel Filter Element Assembly
Main fault Blockage
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

Injector Assembly
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



Injector Driver (EDU)
Main fault Circuit fault: The fuel injector assembly does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as injector assembly
Diagnostic Trouble Code When the injector driver (EDU) has a fault, some DTCs may be stored.

Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Press and Common Rail Pres Sens 2 follow Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Press or Common Rail Pres Sens 2 decreases to a value less than Target Common Rail Pressure).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Main fault
·

Does not move smoothly

·

Does not close completely


Symptoms
·

Rough idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).


Data List Actual EGR Valve Pos., Target EGR Position
·

Generally, Actual EGR Valve Pos. = Target EGR Position +/-5% (fully closed: 0%, fully open: 100%).

·

Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Position (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).

·

EGR valve opens to the halfway point at idling after the engine is warmed up.


EGR Close Lrn. Val., EGR Close Lrn. Status
·

When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0 to 1 V.

·

In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.




d.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List Actual Throttle Position
·

0%: Fully open

·

100%: Fully closed

·

When the ignition switch is turned to ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Rough Idling


·

Engine Speed

·

MAF

·

Intake Air

·

Coolant Temp

·

Engine Speed of Cyl #1 (to #4)

·

Target Common Rail Pressure

·

Fuel Press

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position

·

Target EGR Position

·

Actual EGR Valve Pos.

·

EGR Close Lrn. Status

·

EGR Close Lrn. Val.



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel suction control valve, the ECM needs initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



PROCEDURE

1.CHECK MALFUNCTION CONDITION
a.

Identify when shuddering occurs.

Result:
Result Proceed to
When idling A
When engaging engine clutch at vehicle start B
(Clutch system shudders)




A

2.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT

B

REPAIR OR REPLACE CLUTCH SYSTEM

2.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT
a.

Check the wire harness and connector connections of common rail system components.

OK:

The wire harnesses and connectors are connected securely.


HINT:

The engine may have problems when there is an intermittent disconnection in a circuit related to the fuel pressure sensor, crankshaft position sensor, engine coolant temperature sensor, etc.



Result:
Proceed to
OK
NG



OK

3.READ OUTPUT DTC (RELATING TO ENGINE)

NG

14.REPAIR OR REPLACE HARNESS AND CONNECTOR
3.READ OUTPUT DTC (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the pending DTCs.

Result:
Proceed to
DTCs are not output
Engine related DTCs are output


HINT:

If only DTC P1605 is output, proceed to step 4.




DTCs are not output

4.TAKE SNAPSHOT DURING IDLING (PROCEDURE 4)

Engine related DTCs are output

4.TAKE SNAPSHOT DURING IDLING (PROCEDURE 4)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.


e.

Take a snapshot when idling with no load after the engine is warmed up and when the problem is occurring.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

If rough idling occurs when the A/C switch is on, take another snapshot with the A/C switch on.

·

Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

5.CHECK WHITE SMOKE
5.CHECK WHITE SMOKE
a.

Start the engine.


b.

Fully depress the accelerator pedal, and then release it.


c.

Check whether white smoke is emitted when racing the engine.

NOTICE:

Be sure not to check for white smoke indoors.


HINT:

Depending on whether there is oil mixed with the fuel, or whether there is unburned fuel present, the smell of the exhaust gas differs. When oil is mixed in, the exhaust gas smells like burning oil.


Result:
Proceed to
White smoke is not emitted
White smoke is emitted




White smoke is not emitted

6.CHECK DATA LIST (ENGINE SPEED)

White smoke is emitted

27.CHECK AND REPAIR ENGINE ASSEMBLY
6.CHECK DATA LIST (ENGINE SPEED)
a.

Check engine speed in the snapshot taken in procedure 4 when the engine was idling.

Result:
Result Proceed to
Except below A
Change in engine speed coincides with air conditioning system operation B




A

7.CHECK DATA LIST (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)

B

24.CHECK AIR CONDITIONING SYSTEM
7.CHECK DATA LIST (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)
a.

Check Injection Feedback Val # in the snapshot taken in procedure 4 when the engine was idling.

Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is more than 3 mm3/st and engine vibration is abnormally large A
Except above B


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st, as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

8.INSPECT INJECTOR COMPENSATION CODE

B

15.CHECK DATA LIST (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
8.INSPECT INJECTOR COMPENSATION CODE
a.

Read the injector compensation codes.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION

OK:

Compensation codes stored in the ECM match compensation codes of the installed injector assemblies.



Result:
Proceed to
OK
NG



OK

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)

NG

13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
9.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut / #1 to #4.

Powertrain > Engine > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231
HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

10.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
10.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

11.REPLACE FUEL FILTER ELEMENT ASSEMBLY
11.REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Replace the fuel filter element assembly.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL FILTER>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION


b.

Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPAIR OR REPLACE HARNESS AND CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CHECK DATA LIST (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
a.

Check engine speed in the snapshot taken in procedure 4 when the engine was idling after having been warmed up.

Result:
Result Proceed to
Difference between Fuel Press and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or higher A
Except above B




A

16.INSPECT CLOGGED FUEL PIPE

B

22.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE)
16.INSPECT CLOGGED FUEL PIPE
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail (ALL).


d.

With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.


e.

Check the Target Common Rail Pressure and Fuel Press value.

A261221E07
0.177,1.708 1.365,2.083 1.188,0.375 10 Target Common Rail Pressure 3.854,2.125 5.906,2.448 2.052,0.323 10 Normal Fuel Press 3.75,0.385 5.406,0.646 1.656,0.26 10 Abnormal Fuel Press*1 0.115,0.115 1.823,0.354 1.708,0.24 10 Fuel Pressure During Idling 1.083,2.406 3.75,2.75 2.667,0.344 10 Pressure varies periodically with a period of approximately 2 seconds or more 5.906,1.104 7.146,1.885 1.24,0.781 10 Normal Condition: +/- 5000 kPa (Idling after Engine Warmed Up)

Result:
Result Proceed to
While idling the vehicle, "Fuel Press" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 A
"Common Rail Pressure" is normal while idling the vehicle, but "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2
Except above B


NOTICE:
·

*1: The cause may be a squashed or blocked fuel pipe or hose.

·

*2: The cause may be a clogged fuel filter element assembly.





A

17.REPAIR OR REPLACE CLOGGED FUEL LINE

B

19.REPLACE SUCTION CONTROL VALVE
17.REPAIR OR REPLACE CLOGGED FUEL LINE
a.

Repair or replace the clogged (including frozen fuel) fuel pipe.


b.

Replace the fuel filter element assembly.

HINT:

If "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel Filter Element Assembly.



Result:
Proceed to
NEXT



NEXT

18.BLEED AIR FROM FUEL SYSTEM
18.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.REPLACE SUCTION CONTROL VALVE
a.

Replace the suction control valve.

Click hereEngine / Hybrid System>2AD-FTV FUEL>SUCTION CONTROL VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.BLEED AIR FROM FUEL SYSTEM
20.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

21.PERFORM SUPPLY PUMP INITIALIZATION
21.PERFORM SUPPLY PUMP INITIALIZATION
a.

Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
22.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Powertrain > Engine > Data List
Tester Display
MAF
50003 61 319

f.

Read the MAF value displayed on the GTS while the engine is idling.


g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close / All Data / MAF.

Powertrain > Engine > Active Test
Active Test Display
Activate the EGR Valve Close
Data List Display
MAF
50004 61 183 319

h.

Read the MAF value when the EGR valve is closed using the Active Test function.

HINT:
·

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.

·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.



Result:
GTS Display Result Proceed to
Activate the EGR Valve Close:
OFF (Open) to Close
MAF value does not change A
MAF value changes B


NOTICE:

As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter assembly.


Reference:
EGR Valve Condition (Opening) Measuring Condition MAF (Reference)
Open (67%)
·

Atmosphere pressure: 101 kPa

·

Intake air temperature: 30°C (86°F)

·

Engine coolant temperature: 88°C (190°F)


3 to 12 gm/s
Closed (0%) 7 gm/s or more




A

23.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

B

25.PERFORM PILOT QUANTITY LEARNING (DETAIL)
23.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>2AD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits.

If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

When cleaning the electric EGR control valve assembly, perform initialization procedure.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.



HINT:
·

If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.

·

If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the electric EGR control valve assembly.




Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
24.CHECK AIR CONDITIONING SYSTEM
a.

Check the air conditioning system.

HINT:
·

Be sure to check the air conditioning hoses and pipes.

·

Check the refrigerant pressure.




Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
25.PERFORM PILOT QUANTITY LEARNING (DETAIL)
a.

Perform the pilot quantity learning (detail).

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION


Result:
Proceed to
NEXT



NEXT

26.CHECK ROUGH IDLING OR EXCESSIVE ENGINE VIBRATIONS
26.CHECK ROUGH IDLING OR EXCESSIVE ENGINE VIBRATIONS
a.

Check rough idling or excessive engine vibrations.

Result:
Result Proceed to
Rough idling or excessive engine vibrations do not occur A
Except above B




A

END

B

28.CHECK AND REPLACE ENGINE MOUNTING INSULATOR
27.CHECK AND REPAIR ENGINE ASSEMBLY
a.

Check the following items and repair the malfunctioning part if necessary.

i.


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
28.CHECK AND REPLACE ENGINE MOUNTING INSULATOR
a.

Check the following items and repair or replace the malfunctioning part if necessary.

i.

Check that the engine mounting insulators are installed correctly.


ii.

Check that the engine mounting insulators are not twisted.


iii.

Check that deformation of an engine mounting insulator is not causing the engine to contact the vehicle body.



Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END