Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) C

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  B22C0  BBC Overcurrent  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU.

The backup boost converter helps maintain battery voltage to prevent various functions from failing if power source voltage supplied to the audio and visual system, etc. drops due to the high electrical load when the engine is restarted by stop and start control.

The backup boost converter helps maintain the power source voltage if the battery voltage drops due to the high electrical load when the engine is restarted by stop and start control.

The backup boost converter helps maintain the power source voltage at 13.5 V when its mode changes from standby mode to compensation mode. If the backup boost converter cannot maintain the voltage at the specified level when the engine is restarted by stop and start control, the engine stop and start ECU stores a DTC and blinks the stop and start cancel indicator light. The stop and start cancel indicator light will remain blinking during the trip in which the malfunction occurred.

HINT:

A relay function and fuse function are provided in the backup boost converter for the electrical systems that supply power to the main body ECU (multiplex network body ECU), combination meter assembly and radio receiver assembly*1, radio and display receiver assembly*2 or navigation ECU sub-assembly*3. If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse function operates to protect the malfunctioning electrical system circuit and the relay function shuts off the circuit until the end of the trip. When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

*1: for Radio Receiver Type

*2: for Radio and Display Receiver Type

*3: for Navigation Receiver Type


The fuse function is reset*1 when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON. The backup boost converter supplies power to the main body ECU (multiplex network body ECU), vehicle stability control system, power steering system, meter/gauge system, automatic glare-resistant EC mirror, lane departure alert system, tire pressure warning system and audio and visual system or navigation system.

*1: A semiconductor fuse self-resets according to electric signals.


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
B22C0 BBC Overcurrent The following condition continues for 1 second or more (1 trip detection logic):
·

Overcurrent is detected at the BO1 and IGO1 terminals in the engine stop and start ECU


·

Engine stop and start ECU

·

Wire harness or connector

·

Steering angle sensor (Spiral with sensor cable sub-assembly)

·

Skid control ECU (Brake actuator assembly)

·

Power steering ECU assembly

·

Main body ECU (Multiplex network body ECU)

·

Radio receiver assembly (for Radio Receiver Type)

·

Navigation ECU sub-assembly (for Navigation Receiver Type)

·

Radio and display receiver assembly (for Radio and Display Receiver Type)

·

Inner rear view mirror assembly (w/ Automatic Glare-resistant EC Mirror)

·

Lane departure warning camera (w/ Lane Departure Alert System)

·

Tire pressure warning ECU and receiver (w/ Tire Pressure Warning System)


Blinking DTC stored

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more.


h.

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that battery voltage is low.



i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A299394E01
5.75,0.729 6.208,0.927 0.458,0.198 10 false BIN 5.375,0.74 5.833,0.938 0.458,0.198 10 false A65 5.458,0.563 5.615,0.76 0.156,0.198 10 false 7 2.802,0.896 3.26,1.094 0.458,0.198 10 false BBC 2.667,0.646 2.823,0.844 0.156,0.198 10 false 1 3.146,0.656 3.302,0.854 0.156,0.198 10 false 2 5.729,1.479 6.188,1.677 0.458,0.198 10 false IG2 1.135,1.635 1.594,1.833 0.458,0.198 10 false IG2 2.448,1.375 2.604,1.573 0.156,0.198 10 false 5 1.698,1.385 1.854,1.583 0.156,0.198 10 false 3 2.427,1.74 2.583,1.938 0.156,0.198 10 false 1 1.698,1.74 1.854,1.938 0.156,0.198 10 false 2 2,2.083 2.458,2.281 0.458,0.198 10 false IG2 5.375,1.469 5.833,1.667 0.458,0.198 10 false G87 5.375,5.385 5.833,5.583 0.458,0.198 10 false G87 5.365,6.448 5.823,6.646 0.458,0.198 10 false G87 2.969,2.51 3.427,2.708 0.458,0.198 10 false ACC 3.344,2.5 3.5,2.698 0.156,0.198 10 false 7 3.031,2.75 3.49,2.948 0.458,0.198 10 false IG1 3.344,2.76 3.5,2.958 0.156,0.198 10 false 8 3.042,3.25 3.5,3.448 0.458,0.198 10 false IG2 3.344,3.26 3.5,3.458 0.156,0.198 10 false 3 1.865,3.594 2.177,3.792 0.313,0.198 10 false G4 1.865,3.76 3.354,4.49 1.49,0.729 10 false Ignition or Starter Switch Assembly 2.198,3.25 2.656,3.448 0.458,0.198 10 false AM2 2.208,2.75 2.667,2.948 0.458,0.198 10 false AM1 2.021,2.771 2.177,2.969 0.156,0.198 10 false 5 2.021,3.24 2.177,3.438 0.156,0.198 10 false 4 0.708,3.5 1.167,3.698 0.458,0.198 10 false AM2 5.729,5.396 6.188,5.594 0.458,0.198 10 false ACC 3.74,5.531 4.198,5.729 0.458,0.198 10 false ACC 3.906,5.042 4.365,5.24 0.458,0.198 10 false IGN 1.792,4.969 2.25,5.167 0.458,0.198 10 false AM1 5.417,1.271 5.729,1.469 0.313,0.198 10 false 20 5.406,5.208 5.719,5.406 0.313,0.198 10 false 19 5.417,6.26 5.729,6.458 0.313,0.198 10 false 17 5.729,6.448 6.188,6.646 0.458,0.198 10 false IG1 2.958,6 3.417,6.198 0.458,0.198 10 false ACC 2.823,7.083 3.823,7.25 1,0.167 10 false IG1 NO. 1 3.656,6.594 4.573,6.792 0.917,0.198 10 false EPS-IG 3.615,4.583 3.927,4.781 0.313,0.198 10 false 3B 3.75,4.385 4.063,4.583 0.313,0.198 10 false 14 4.271,4.583 4.583,4.781 0.313,0.198 10 false 3C 4.396,4.385 4.708,4.583 0.313,0.198 10 false 37 4.417,5.396 4.729,5.594 0.313,0.198 10 false 3D 4.417,5.208 4.729,5.406 0.313,0.198 10 false 51 4.406,5.74 4.719,5.938 0.313,0.198 10 false 3C 4.417,5.573 4.729,5.771 0.313,0.198 10 false 45 4.417,6.448 4.729,6.646 0.313,0.198 10 false 3D 4.427,6.26 4.74,6.458 0.313,0.198 10 false 43 4.406,6.813 4.719,7.01 0.313,0.198 10 false 3C 4.427,6.646 4.74,6.844 0.313,0.198 10 false 43 1.292,6.813 1.604,7.01 0.313,0.198 10 false 3D 1.333,6.635 1.49,6.833 0.156,0.198 10 false 9 1.583,4.583 1.896,4.781 0.313,0.198 10 false 3C 1.479,4.396 1.792,4.594 0.313,0.198 10 false 48 1.292,6.438 1.604,6.635 0.313,0.198 10 false 3A 1.344,6.271 1.5,6.469 0.156,0.198 10 false 1 0.667,6.615 1.125,6.813 0.458,0.198 10 false ALT 1.542,7.51 4.406,7.865 2.865,0.354 10 false Instrument Panel Junction Block Assembly 0.635,7.719 1.708,7.917 1.073,0.198 10 false Battery 5.313,7.854 7.042,8.385 1.729,0.531 10 false Engine Stop and Start ECU 0.073,0.063 5.031,0.302 4.958,0.24 12 false w/o Entry and Start System: 0.438,7.01 1.51,7.208 1.073,0.198 10 false FL MAIN

A299395E01
5.375,0.74 5.833,0.938 0.458,0.198 10 false A65 5.469,0.563 5.625,0.76 0.156,0.198 10 false 7 5.75,0.74 6.208,0.938 0.458,0.198 10 false BIN 5.74,1.469 6.198,1.667 0.458,0.198 10 false IG2 5.375,1.458 5.833,1.656 0.458,0.198 10 false G87 5.375,5.469 5.833,5.667 0.458,0.198 10 false G87 5.375,6.542 5.833,6.74 0.458,0.198 10 false G87 5.729,5.458 6.188,5.656 0.458,0.198 10 false ACC 5.74,6.531 6.198,6.729 0.458,0.198 10 false IG1 5.427,1.281 5.74,1.479 0.313,0.198 10 false 20 5.417,5.271 5.729,5.469 0.313,0.198 10 false 19 5.417,6.354 5.729,6.552 0.313,0.198 10 false 17 2.75,0.896 3.208,1.094 0.458,0.198 10 false BBC 3.083,0.656 3.24,0.854 0.156,0.198 10 false 2 2.604,0.656 2.76,0.854 0.156,0.198 10 false 1 1.927,2.115 2.385,2.313 0.458,0.198 10 false IG2 1.104,1.625 1.563,1.823 0.458,0.198 10 false IG2 2.417,1.375 2.573,1.573 0.156,0.198 10 false 5 2.406,1.729 2.563,1.927 0.156,0.198 10 false 1 1.688,1.375 1.844,1.573 0.156,0.198 10 false 3 1.688,1.729 1.844,1.927 0.156,0.198 10 false 2 2.844,2.542 3.458,2.74 0.615,0.198 10 false IG2D 3.24,2.542 3.698,2.74 0.458,0.198 10 false G82 1.792,3.271 2.25,3.469 0.458,0.198 10 false G82 3.333,2.365 3.49,2.563 0.156,0.198 10 false 9 1.885,3.104 2.042,3.302 0.156,0.198 10 false 2 3.25,2.917 3.708,3.115 0.458,0.198 10 false G84 3.25,3.271 3.708,3.469 0.458,0.198 10 false G84 2.844,2.917 3.458,3.115 0.615,0.198 10 false IG1D 2.771,3.281 3.385,3.479 0.615,0.198 10 false ACCD 2.125,3.271 2.438,3.469 0.313,0.198 10 false +B 3.323,2.74 3.479,2.938 0.156,0.198 10 false 6 3.323,3.104 3.479,3.302 0.156,0.198 10 false 4 1.823,3.667 3.667,4.125 1.844,0.458 10 false Certification ECU (Smart Key ECU Assembly) 0.958,3.427 1.417,3.625 0.458,0.198 10 false AM2 3.698,4.583 4.01,4.781 0.313,0.198 10 false 3B 4.354,4.583 4.667,4.781 0.313,0.198 10 false 3C 3.802,4.375 4.115,4.573 0.313,0.198 10 false 14 4.479,4.375 4.792,4.573 0.313,0.198 10 false 37 3.729,5.604 4.188,5.802 0.458,0.198 10 false ACC 4,5.031 4.458,5.229 0.458,0.198 10 false IGN 4.417,5.479 4.729,5.677 0.313,0.198 10 false 3D 4.417,6.542 4.729,6.74 0.313,0.198 10 false 3D 1.938,6.906 2.25,7.104 0.313,0.198 10 false 3D 4.438,5.302 4.75,5.5 0.313,0.198 10 false 51 4.427,5.667 4.74,5.865 0.313,0.198 10 false 45 4.406,5.833 4.719,6.031 0.313,0.198 10 false 3C 4.427,6.354 4.75,6.5 0.323,0.146 10 false 43 4.417,6.719 4.74,6.865 0.323,0.146 10 false 43 4.406,6.906 4.719,7.104 0.313,0.198 10 false 3C 3.635,6.677 4.552,6.875 0.917,0.198 10 false EPS-IG 2.958,6.083 3.417,6.281 0.458,0.198 10 false ACC 2.802,7.177 4.177,7.375 1.375,0.198 10 false IG1 NO. 1 1.99,6.729 2.146,6.927 0.156,0.198 10 false 9 1.938,6.531 2.25,6.729 0.313,0.198 10 false 3A 1.99,6.344 2.146,6.542 0.156,0.198 10 false 1 0.688,6.677 1.146,6.875 0.458,0.198 10 false ALT 1.885,7.563 4.594,7.927 2.708,0.365 10 false Instrument Panel Junction Block Assembly 0.615,7.688 1.688,7.885 1.073,0.198 10 false Battery 5.333,7.854 7.083,8.167 1.75,0.313 10 false Engine Stop and Start ECU 0.063,0.052 4.833,0.292 4.771,0.24 12 false w/ Entry and Start System: 0.479,7.094 1.552,7.292 1.073,0.198 10 false FL MAIN

A299396E01
0.563,1.594 2.927,1.865 2.365,0.271 10 false Inner Rear View Mirror Assembly*4 0.542,1.417 0.854,1.615 0.313,0.198 10 false Q6 2.281,1.24 2.594,1.438 0.313,0.198 10 false IG 2.583,1.146 2.74,1.344 0.156,0.198 10 false 4 0.542,2.344 0.833,2.635 0.292,0.292 10 false h1 0.542,2.542 2.823,2.75 2.281,0.208 10 false Power Steering ECU Assembly 2.281,2.156 2.594,2.354 0.313,0.198 10 false IG 2.573,2.052 2.729,2.25 0.156,0.198 10 false 1 0.375,3.458 4.104,3.813 3.729,0.354 10 false Instrument Panel Junction Block Assembly (Main Body ECU (Multiplex Network Body ECU)) 2.583,3.031 2.896,3.229 0.313,0.198 10 false 40 2.292,3.146 2.604,3.344 0.313,0.198 10 false IG 0.354,4.677 4.406,4.99 4.052,0.313 10 false Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly) 0.344,4.49 0.802,4.688 0.458,0.198 10 false G12 2.313,4.333 2.625,4.531 0.313,0.198 10 false IG 2.583,4.198 2.74,4.396 0.156,0.198 10 false 4 0.583,5.427 1.042,5.625 0.458,0.198 10 false Q13 0.583,5.646 3.146,5.844 2.563,0.198 10 false Lane Departure Warning Camera*5 0.552,0.552 0.927,0.729 0.375,0.177 10 false M30 0.552,0.729 3.625,0.917 3.073,0.188 10 false Tire Pressure Warning ECU and Receiver*3 0.573,6.667 3.521,6.906 2.948,0.24 10 false Skid Control ECU (Brake Actuator Assembly) 0.573,6.458 1.031,6.656 0.458,0.198 10 false A64 4.135,6.396 4.552,6.563 0.417,0.167 10 false *1 4.135,5.552 4.552,5.719 0.417,0.167 10 false *2 0.146,7.135 1.833,7.333 1.688,0.198 10 false *1: for LHD 0.146,7.49 1.833,7.688 1.688,0.198 10 false *2: for RHD 0.146,7.823 3.042,7.969 2.896,0.146 10 false *3: w/ Tire Pressure Warning System 0.146,8.167 3.24,8.406 3.094,0.24 10 false *4: w/ Automatic Glare-resistant EC Mirror 0.146,8.5 2.625,8.688 2.479,0.188 10 false *5: w/ Lane Departure Alert System 2.219,5.177 2.677,5.375 0.458,0.198 10 false IGB 2.604,5.073 2.76,5.271 0.156,0.198 10 false 7 2.25,6.271 2.708,6.469 0.458,0.198 10 false IG1 2.573,6.135 2.885,6.333 0.313,0.198 10 false 34 5.667,3.781 6.281,3.979 0.615,0.198 10 false IGO1 5.281,3.771 5.74,3.969 0.458,0.198 10 false G87 5.333,3.573 5.646,3.771 0.313,0.198 10 false 12 5.302,6.667 5.76,6.865 0.458,0.198 10 false A65 5.365,6.469 5.521,6.667 0.156,0.198 10 false 8 5.656,6.677 6.115,6.875 0.458,0.198 10 false GND 5.25,8 7.083,8.208 1.833,0.208 10 false Engine Stop and Start ECU 2.542,0.156 2.698,0.354 0.156,0.198 10 false 1 2.271,0.271 2.583,0.469 0.313,0.198 10 false IG 0.365,3.292 0.823,3.49 0.458,0.198 10 false 3D 3.688,5.167 4.104,5.333 0.417,0.167 10 false *5

A299397E01
5.292,1.219 5.75,1.417 0.458,0.198 10 false G87 5.688,1.219 6.302,1.417 0.615,0.198 10 false IGO2 5.333,1.01 5.646,1.208 0.313,0.198 10 false 11 0.208,1.563 0.667,1.76 0.458,0.198 10 false G16 0.229,1.76 4.208,1.958 3.979,0.198 10 false Combination Meter Assembly 2.354,1.219 2.813,1.417 0.458,0.198 10 false IG+ 2.719,1.104 3.031,1.302 0.313,0.198 10 false 39 2.271,2.625 2.729,2.823 0.458,0.198 10 false +B1 2.167,3.344 2.781,3.542 0.615,0.198 10 false ACC1 2.76,2.51 2.917,2.708 0.156,0.198 10 false 4 2.75,3.26 2.906,3.458 0.156,0.198 10 false 3 0.385,3.719 0.844,3.917 0.458,0.198 10 false G46*1 0.396,3.875 4.219,4.073 3.823,0.198 10 false Radio Receiver Assembly*1 0.385,4.156 1.302,4.354 0.917,0.198 10 false G137*2 0.396,4.323 3.094,4.542 2.698,0.219 10 false Navigation ECU Sub-assembly*2 0.385,4.625 1.302,4.823 0.917,0.198 10 false G141*3 0.396,4.792 2.969,5.031 2.573,0.24 10 false Radio and Display Receiver Assembly*3 0.094,5.167 2.01,5.396 1.917,0.229 10 false *1: for Radio Receiver Type 0.104,5.458 2.229,5.677 2.125,0.219 10 false *2: for Navigation Receiver Type 2.396,5.177 5.156,5.51 2.76,0.333 10 false *3: for Radio and Display Receiver Type 5.292,4.375 7.052,4.646 1.76,0.271 10 false Engine Stop and Start ECU 5.281,2.635 5.74,2.833 0.458,0.198 10 false G87 5.688,2.625 6.146,2.823 0.458,0.198 10 false BO1 5.365,2.427 5.521,2.625 0.156,0.198 10 false 2 5.677,3.344 6.135,3.542 0.458,0.198 10 false ACO 5.365,3.135 5.521,3.333 0.156,0.198 10 false 3 5.302,3.354 5.76,3.552 0.458,0.198 10 false G87

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>FREEZE FRAME DATA

·

If electrical load from additional devices installed on the vehicle (aftermarket audio system, etc.) is applied to the BO1 or IGO1 terminal in the engine stop and start ECU, the fuse function of the backup boost converter may operate.

If the fuse function of the backup boost converter operates, any systems connected to the BO1 or IGO1 terminal in the engine stop and start ECU will not operate.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC FUSE)
a.

Disconnect the A65 engine stop and start ECU connector.


b.

Remove the BBC fuse from engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A65-7 (BIN) - BBC fuse terminal 2 Always Below 1 Ω
A65-7 (BIN) - Body ground Always 10 kΩ or higher
BBC fuse terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

for Radio Receiver Type:

Disconnect the G46 radio receiver assembly connector.


c.

for Navigation Receiver Type:

Disconnect the G137 navigation ECU sub-assembly connector.


d.

for Radio and Display Receiver Type:

Disconnect the G141 radio and display receiver assembly connector.


e.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


f.

Disconnect the h1 power steering ECU assembly connector.


g.

Disconnect the 3D instrument panel junction block assembly (main body ECU (multiplex network body ECU)) connector.


h.

Disconnect the G12 steering angle sensor (spiral with sensor cable sub-assembly) connector.


i.

w/ Automatic Glare-resistant EC Mirror:

Disconnect the Q6 inner rear view mirror assembly connector.


j.

w/ Lane Departure Alert System:

Disconnect the Q13 lane departure warning camera connector.


k.

w/ Tire Pressure Warning System:

Disconnect the M30 tire pressure warning ECU and receiver connector.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-2 (BO1) - G46-4 (+B1)*1 Always Below 1 Ω
G87-2 (BO1) - G137-4 (+B1)*2 Always Below 1 Ω
G87-2 (BO1) - G141-4 (+B1)*3 Always Below 1 Ω
G87-12 (IGO1) - A64-34 (IG1) Always Below 1 Ω
G87-12 (IGO1) - h1-1 (IG) Always Below 1 Ω
G87-12 (IGO1) - 3D-40 (IG) Always Below 1 Ω
G87-12 (IGO1) - G12-4 (IG) Always Below 1 Ω
G87-12 (IGO1) - Q6-4 (IG)*4 Always Below 1 Ω
G87-12 (IGO1) - Q13-7 (IGB)*5 Always Below 1 Ω
G87-12 (IGO1) - M30-1 (IG)*6 Always Below 1 Ω
G87-2 (BO1) - Body ground Always 10 kΩ or higher
G87-12 (IGO1) - Body ground Always 10 kΩ or higher


·

*1: for Radio Receiver Type

·

*2: for Navigation Receiver Type

·

*3: for Radio and Display Receiver Type

·

*4: w/ Automatic Glare-resistant EC Mirror

·

*5: w/ Lane Departure Alert System

·

*6: w/ Tire Pressure Warning System



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU
a.

Disconnect the engine stop and start ECU connector.

A295480C03
1.5,0.583 1.917,0.833 0.417,0.25 3.167,0.583 3.583,0.833 0.417,0.25 5,0.583 5.417,0.833 0.417,0.25 3.75,1.979 4.458,1.323 false 5.448,2.115 5.781,1.333 false 1.365,2.094 1.583,1.594 false 0.115,0.052 0.427,0.208 0.313,0.156 10 *a 1.594,0.625 1.906,0.823 0.313,0.198 10 A65 3.26,0.625 3.573,0.823 0.313,0.198 10 A66 5.083,0.635 5.396,0.833 0.313,0.198 10 G87 5.333,2.135 5.792,2.333 0.458,0.198 10 BO1 3.583,2.01 4.042,2.208 0.458,0.198 10 IGO1 1.208,2.115 1.667,2.313 0.458,0.198 10 GND
*a Component without harness connected
(Engine Stop and Start ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-2 (BO1) - A65-8 (GND) Always 10 kΩ or higher
G87-12 (IGO1) - A65-8 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK VEHICLE CONDITION (BO1, IGO1 CIRCUIT)

NG

4.CHECK VEHICLE CONDITION (BO1, IGO1 CIRCUIT)
a.

Check that additional devices installed to the vehicle (aftermarket audio system, etc.) are not connected to the BO1 or IGO1 terminal circuit in the engine stop and start ECU.

Result:
Result Proceed to
Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is not applied. A
Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is applied. B




A

GO TO TROUBLE AREAS (TROUBLESHOOTING PROCEDURE FOR ECUS CONNECTED TO BO1 AND IGO1 TERMINALS)

B

END (REMOVE ELECTRICAL LOAD FROM ADDITIONAL DEVICE)