Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) C

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  P0562  System Voltage Low  


DESCRIPTION

The engine stop and start ECU monitors +B terminal voltage while the engine is stopped by stop and start control. If the voltage drops below the specified level, the engine stop and start ECU stores DTC P0562 and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0562 System Voltage Low Both of the following conditions continue for 2 seconds or more (1 trip detection logic):
·

+B terminal voltage is 9 V or less.

·

During engine stop by stop and start control.


·

Battery

·

Wire harness or connector

·

EFI-MAIN NO. 2 relay

·

Engine stop and start ECU


Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more.


h.

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that battery voltage is low.



i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A299440E01
5.573,0.74 6.031,0.938 0.458,0.198 10 false A65 5.583,4.271 6.042,4.469 0.458,0.198 10 false A65 5.938,0.74 6.25,0.938 0.313,0.198 10 false +B 5.938,3.708 6.396,3.906 0.458,0.198 10 false VB- 5.573,3.708 6.031,3.906 0.458,0.198 10 false A66 5.656,0.552 5.813,0.75 0.156,0.198 10 false 5 5.615,3.51 5.927,3.708 0.313,0.198 10 false 17 5.656,4.094 5.813,4.292 0.156,0.198 10 false 8 5.917,4.281 6.375,4.479 0.458,0.198 10 false GND 2.552,1.521 3.75,1.75 1.198,0.229 10 false EFI-MAIN NO. 2 1.083,0.917 2.281,1.146 1.198,0.229 10 false EFI-MAIN NO. 2 2.615,0.635 2.771,0.833 0.156,0.198 10 false 5 3.406,0.646 3.563,0.844 0.156,0.198 10 false 3 3.396,1.052 3.552,1.25 0.156,0.198 10 false 1 2.604,1.052 2.76,1.25 0.156,0.198 10 false 2 0.823,4.698 1.896,4.896 1.073,0.198 10 false Battery 2.51,3.073 2.969,3.271 0.458,0.198 10 false A61 2.969,2.594 3.583,2.792 0.615,0.198 10 false MREL 3.458,2.469 3.771,2.667 0.313,0.198 10 false 45 2.521,3.25 2.979,3.448 0.458,0.198 10 false ECM 5.25,4.833 7.083,5.052 1.833,0.219 10 false Engine Stop and Start ECU 0.667,3.76 1.74,3.958 1.073,0.198 10 false FL MAIN 3.885,0.906 5.26,1.104 1.375,0.198 10 false EFI NO. 1

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>FREEZE FRAME DATA



PROCEDURE

1.READ VALUE USING GTS (BATTERY VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

HINT:

Do not start the engine.



c.

Turn the GTS on.


d.

Turn off all electrical systems.


e.

Enter the following menus: Powertrain / Stop and Start / Data List / Battery Voltage.

Powertrain > Stop and Start > Data List
Tester Display
Battery Voltage
50003 227 6

f.

Read the battery voltage displayed on the GTS screen.

Result:
Proceed to
Below 4 V
4 to 14 V




Below 4 V

2.INSPECT RELAY (EFI-MAIN NO. 2 RELAY)

4 to 14 V

2.INSPECT RELAY (EFI-MAIN NO. 2 RELAY)
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (+B TERMINAL VOLTAGE)

NG

REPLACE RELAY (EFI-MAIN NO. 2 RELAY)

3.CHECK HARNESS AND CONNECTOR (+B TERMINAL VOLTAGE)
a.

Turn the ignition switch to ON.

A285225C26
2.021,0.833 2.354,1.063 0.333,0.229 2.74,2.219 2.594,1.781 false 0.344,0.24 0.688,0.51 0.344,0.271 10 *a 2.073,0.875 2.531,1.073 0.458,0.198 10 A65 2.688,2.25 3.146,2.448 0.458,0.198 10 +B
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A65-5 (+B) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 2 RELAY)