Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) C

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  P1780  Discrepancy between Neutral Position SW and Shift Position  


DESCRIPTION

The engine stop and start ECU detects a malfunction by comparing the shift position signal with the neutral position switch signal input state. When a malfunction occurs, the engine stop and start ECU stores this DTC, blinks the stop and start cancel indicator light, and prohibits the stop and start control.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1780 Discrepancy between Neutral Position SW and Shift Position The following condition continues for 1 second or more (1 trip detection logic):
·

Open or short in neutral position switch circuit.


·

Neutral position switch

·

Engine stop and start ECU

·

Wire harness or connector


Blinking DTC stored

WIRING DIAGRAM

A285528E07
2.167,0.729 2.688,0.958 0.521,0.229 10 W1 2.177,1.198 2.635,1.427 0.458,0.229 10 F+ 2.073,1.646 2.521,1.958 0.448,0.313 10 TMN 1.073,2.115 1.521,2.333 0.448,0.219 10 B63 1.083,2.26 2.667,2.5 1.583,0.24 10 Neutral Position Switch 2.469,0.635 3.031,0.938 0.563,0.302 10 1 2.469,1.094 2.802,1.365 0.333,0.271 10 3 2.469,1.552 2.833,1.823 0.365,0.271 10 2 4.49,0.625 4.969,0.906 0.479,0.281 10 26 4.49,1.073 4.833,1.313 0.344,0.24 10 25 4.5,1.552 4.802,1.792 0.302,0.24 10 27 4.75,0.729 5.344,1.01 0.594,0.281 10 TMVC 4.75,1.188 5.188,1.417 0.438,0.229 10 TME2 4.75,1.656 5.333,2.021 0.583,0.365 10 TMN 4.594,2.125 5.073,2.344 0.479,0.219 10 A66 4.583,2.281 6.573,2.5 1.99,0.219 10 Engine Stop and Start ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>FREEZE FRAME DATA


PROCEDURE

1.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 227 9

e.

Read the value when the shift lever is in neutral and any other position

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in neutral ON
Shift lever in any position other than neutral OFF



Result:
Proceed to
NG
OK



NG

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)

OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the B63 neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-26 (TMVC) - B63-1 (W1) Always Below 1 Ω
A66-25 (TME2) - B63-3 (F+) Always Below 1 Ω
A66-27 (TMN) - B63-2 (TMN) Always Below 1 Ω
A66-26 (TMVC) - Body ground Always 10 kΩ or higher
B63-1 (W1) - Body ground Always 10 kΩ or higher
A66-25 (TME2) - Body ground Always 10 kΩ or higher
B63-3 (F+) - Body ground Always 10 kΩ or higher
A66-27 (TMN) - Body ground Always 10 kΩ or higher
B63-2 (TMN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)
a.

Measure the voltage according to the value(s) in the table below.

A285225C28
3.198,0.896 3.552,1.135 0.354,0.24 2.729,2.25 2.885,1.698 false 3.135,2.24 3.042,1.708 false 0.427,0.354 0.74,0.552 0.313,0.198 10 *a 3.26,0.938 3.719,1.135 0.458,0.198 10 A66 2.552,2.292 3.01,2.49 0.458,0.198 10 TMN 3.021,2.281 3.479,2.479 0.458,0.198 10 TME2
*a Component with harness connected
(Engine Stop and Start ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A66-27 (TMN) - A66-25 (TME2) Ignition switch ON, shift lever in neutral 2.7 to 4.3 V
Ignition switch ON, shift lever in any position other than neutral 0.7 to 1.9 V



Result:
Proceed to
OK
NG



OK

NG