Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) J

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  Stop and Start System does not Operate (Battery Condition)  


DESCRIPTION

When the stop and start system does not operate, check whether the operation is prohibited because the battery conditions are not met.

HINT:

Data List items:

·

Oper Permission (Battery)

·

Oper Permission (Start Min Volt 1)

·

Oper Permission (Start Min Volt 2)

·

Oper Permission (Start Min Volt 3)

·

Oper Permission (Start Min Volt 4)

·

Oper Permission (Battery Current)

·

Oper Permission (Integrated Current)

·

Oper Prohibition (Jump Start)

·

Oper Prohibition (Manual Start)



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Read the DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 227
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

2.READ VALUE USING GTS

DTC is output

2.READ VALUE USING GTS
a.

Enter the following menus: Powertrain / Stop and Start / Data List.


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Oper Permission (Battery) Permission of stop and start control based on the battery conditions NG/OK OK: Stop and start control is permitted due to battery condition, or Active Test (forced permission) is performed -
Oper Permission (Start Min Volt 1) Permission of stop and start control based on the battery conditions NG/OK OK: Battery temperature is 0°C (32°F) or less and the minimum voltage at starter ON is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
Oper Permission (Start Min Volt 2) Permission of stop and start control based on the battery conditions NG/OK OK: Battery temperature is 0°C (32°F) or higher and the minimum voltage at starter ON is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
Oper Permission (Start Min Volt 3) Permission of stop and start control based on the battery conditions NG/OK OK: Battery temperature is 0°C (32°F) or less and the minimum voltage right after engine cranking is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
Oper Permission (Start Min Volt 4) Permission of stop and start control based on the battery conditions NG/OK OK: Battery temperature is 0°C (32°F) or higher and the minimum voltage right after engine cranking is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
Oper Permission (Battery Current) Permission of stop and start control based on the battery conditions NG/OK OK: Battery discharge current is -125 A or less Engine stop and start ECU calculated value
Oper Permission (Integrated Current) Permission of stop and start control based on the integrated current value conditions NG/OK OK: Integrated current value more than specified The status depend on the value of "Integrated Current", and OK/NG threshold differs according to the battery temperature.
Oper Prohibition (Jump Start) Prohibition of stop and start control based on the jump start conditions Permit/Prohibit Prohibit: Engine started with the engine hood open and the ignition switch turned to START When Prohibit is displayed, the stop and start control will be prohibited until the ignition switch is turned off.
Oper Prohibition (Manual Start) Prohibition of stop and start control based on the manual start conditions Permit/Prohibit Prohibit: During manual start When Prohibit is displayed, the stop and start control will be prohibited until the ignition switch is turned off.
Conditions for Manual Start:
·

Clutch start switch OFF or vehicle speed signal input

·

Neutral position switch OFF

·

Starter signal OFF


Powertrain > Stop and Start > Data List
Tester Display
Oper Permission (Battery)
Oper Permission (Start Min Volt 1)
Oper Permission (Start Min Volt 2)
Oper Permission (Start Min Volt 3)
Oper Permission (Start Min Volt 4)
Oper Permission (Battery Current)
Oper Permission (Integrated Current)
Oper Prohibition (Jump Start)
Oper Prohibition (Manual Start)
50003 227 120,124,123,122,121,125,126,128,129

Result:
Proceed to
NEXT



NEXT

3.READ VALUE USING GTS (OPER PERMISSION (BATTERY))
3.READ VALUE USING GTS (OPER PERMISSION (BATTERY))
HINT:

Check whether stop and start control was prohibited based on the battery conditions or other conditions.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Battery).


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Oper Permission (Battery) Permission of stop and start control based on the battery conditions NG/OK OK: Stop and start control is permitted due to battery condition, or Active Test (forced permission) is performed -
Powertrain > Stop and Start > Data List
Tester Display
Oper Permission (Battery)
50003 227 120
Result:
Proceed to
NG is displayed
OK is displayed




NG is displayed

4.READ VALUE USING GTS (STATUS OF BATTERY CHARGE CONTROL)

OK is displayed

END (CHECK OTHER STOP AND START CONTROL PERMISSION/PROHIBITION CONDITIONS)

4.READ VALUE USING GTS (STATUS OF BATTERY CHARGE CONTROL)
HINT:

Check whether stop and start control was prohibited based on the battery charge control mode.


a.

Start the engine and allow it to idle.


b.

Enter the following menus: Powertrain / Stop and Start / Data List / Status of Battery Charge Control.


c.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Status of Battery Charge Control Battery charge control status Change Control Condition Mode/Stop and Start Standalone/Refresh Charge Mode/Stop and Start Restriction Mode/Temperature High/Low Mode/Abnormal Mode/Battery Condition Judgment Mode/Low Temperature Mode - -
Powertrain > Stop and Start > Data List
Tester Display
Status of Battery Charge Control
50003 227 273
Result:
Result Proceed to
"Refresh Charge Mode", "Battery Condition Judgment Mode" or "Abnormal Mode" is not displayed A
"Refresh Charge Mode" is displayed B
"Battery Condition Judgment Mode" is displayed C
"Abnormal Mode" is displayed D


HINT:

If "Refresh Charge Mode" is displayed, leave the vehicle idling for 30 to 60 minutes.




A

5.READ VALUE USING GTS (OPER PERMISSION (START MIN VOLT 1, 2, 3, 4))

B

END (STOP AND START CONTROL PROHIBITED IN REFRESH CHARGE MODE)

C

END (STOP AND START CONTROL PROHIBITED IN BATTERY CONDITION JUDGMENT MODE)

D

5.READ VALUE USING GTS (OPER PERMISSION (START MIN VOLT 1, 2, 3, 4))
HINT:

Check whether stop and start control was prohibited based on the minimum starting voltage of the battery condition.


a.

Enter the following menus: Powertrain / Stop and Start / Data List.


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Oper Permission (Start Min Volt 1) Permission of stop and start control based on the battery conditions NG/OK OK: Battery temperature is 0°C (32°F) or less and the minimum voltage at starter ON is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
Oper Permission (Start Min Volt 2) Permission of stop and start control based on the battery conditions NG/OK OK: Battery temperature is 0°C (32°F) or higher and the minimum voltage at starter ON is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
Oper Permission (Start Min Volt 3) Permission of stop and start control based on the battery conditions NG/OK OK: Battery temperature is 0°C (32°F) or less and the minimum voltage right after engine cranking is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
Oper Permission (Start Min Volt 4) Permission of stop and start control based on the battery conditions NG/OK OK: Battery temperature is 0°C (32°F) or higher and the minimum voltage right after engine cranking is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
Powertrain > Stop and Start > Data List
Tester Display
Oper Permission (Start Min Volt 1)
Oper Permission (Start Min Volt 2)
Oper Permission (Start Min Volt 3)
Oper Permission (Start Min Volt 4)
50003 227 124,123,122,121
Result:
Proceed to
OK is displayed for 2 or more items
OK is displayed for 1 item or none


i.

The Data List item "Oper Permission (Start Min Volt 1, 2, 3, 4)" is judged OK or NG according to the values of the following Data List items.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Battery Temp (Start) Battery temperature at engine start Min.: -40°C (-40°F), Max.: 100°C (212°F) Same as temperature around battery at engine start (after engine start) -
Ambient Temp Sensor Ambient temperature Min.: -30°C (-22°F), Max.: 50°C (122°F) Close to ambient temperature -
Min Voltage(Cranking) Minimum battery voltage while engine cranking (incurrent trip) Min.: 0 V, Max.: 327.67 V 6 to 11 V Lowest battery voltage measured in a 5 second period after the starter starts operating.
Min Volt(After Cranking) Minimum battery voltage just after engine cranking Min.: 0 V, Max.: 327.67 V 6 to 11 V Minimum battery voltage while starter driving
Powertrain > Stop and Start > Data List
Tester Display
Battery Temp (Start)
Ambient Temp Sensor
Min Voltage(Cranking)
Min Volt(After Cranking)
50003 227 153,63,67,210
Permission Criteria:
Tester Display Starting Battery Voltage Battery Temperature*1
Oper Permission (Start Min Volt 1)*2 8.14 V or higher 0°C (32°F) or less
Oper Permission (Start Min Volt 2)*2 8.14 V or higher Higher than 0°C (32°F)
Oper Permission (Start Min Volt 3)*3 8.14 V or higher 0°C (32°F) or less
Oper Permission (Start Min Volt 4)*3 8.14 V or higher Higher than 0°C (32°F)


·

*1: Read the Data List items "Battery Temp (Start)" and "Ambient Temp Sensor" when checking the battery temperature.

·

*2: Operation is permitted when the minimum voltage is 8.14 V or more when 0.0049 seconds have elapsed after cranking the engine.

·

*3: Operation is permitted when the minimum voltage is 8.14 V or more right after cranking the engine.





OK is displayed for 2 or more items

6.READ VALUE USING GTS (OPER PERMISSION (BATTERY CURRENT))

OK is displayed for 1 item or none

END (CHECK BATTERY CONDITION AND RECHARGE OR REPLACE BATTERY)

6.READ VALUE USING GTS (OPER PERMISSION (BATTERY CURRENT))
HINT:

Check whether the stop and start control was prohibited based on the battery discharge current battery condition.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Battery Current).


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Oper Permission (Battery Current) Permission of stop and start control based on the battery conditions NG/OK OK: Battery discharge current is -125 A or less Engine stop and start ECU calculated value
Powertrain > Stop and Start > Data List
Tester Display
Oper Permission (Battery Current)
50003 227 125
Result:
Proceed to
OK is displayed
NG is displayed


i.

The Data List item "Oper Permission (Battery Current)" is judged OK or NG according to the values of the following Data List items.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Battery Current Battery current Min.: 0 A, Max.: 124.99 A - -
Powertrain > Stop and Start > Data List
Tester Display
Battery Current
50003 227 60
Permission Criteria:
Tester Display Battery Current
Oper Permission (Battery Current) -125 A or less





OK is displayed

7.READ VALUE USING GTS (OPER PERMISSION (INTEGRATED CURRENT))

NG is displayed

END (REDUCE ELECTRICAL LOAD)

7.READ VALUE USING GTS (OPER PERMISSION (INTEGRATED CURRENT))
HINT:

Check whether the stop and start control was prohibited based on the integrated current value battery condition.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Integrated Current).


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Oper Permission (Integrated Current) Permission of stop and start control based on the integrated current value conditions NG/OK OK: Integrated current value more than specified The condition is judged based on the integrated current value.
The status depend on the value of "Integrated Current", and OK/NG threshold differs according to the battery temperature.
Powertrain > Stop and Start > Data List
Tester Display
Oper Permission (Integrated Current)
50003 227 126
Result:
Proceed to
OK is displayed
NG is displayed




OK is displayed

8.READ VALUE USING GTS (STATE OF BBC AND BBC CHECK RESULT)

NG is displayed

18.READ VALUE USING GTS (INTEGRATED CURRENT)
8.READ VALUE USING GTS (STATE OF BBC AND BBC CHECK RESULT)
HINT:

Check the operation of the backup boost converter.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / State of BBC and BBC Check Result.


b.

Check the following items on the GTS display.

Powertrain > Stop and Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
State of BBC Backup boost converter status Cycle Err / Overvol / Overload / Normal / Low Vol / Duty Err / S&S Sensor Electric Supply Low / S&S CPU Malfunction / BBC Overcurrent / S&S Starter Overcurrent / S&S Reduced Voltage Resetstatus Normal: Backup boost converter operating normally
·

Cycle Err:

·

Abnormal output voltage cycle is detected


·

Overvol:

·

When the ignition switch is ON:

1.

Overvoltage is detected at the control IC power source within the backup boost converter

2.

Overheating is detected at the control IC power source within the backup boost converter



·

When boosting:

1.

Error is detected in the feedback circuit in the backup boost converter

2.

Too high or low output voltage



·

Overload:

·

Overcurrent is detected.


·

Low Vol:

·

A decrease in the voltage of the control IC power source within the backup boost converter is detected when ignition switch is turned to ON.


·

Duty Err:

·

Abnormal duty ratio is detected



BBC Check Result Backup boost converter check result Normal / Abnormal - -
Powertrain > Stop and Start > Data List
Tester Display
State of BBC
BBC Check Result
50003 227 69,70
Result:
Proceed to
Normal is displayed
Normal is not displayed




Normal is displayed

9.READ VALUE USING GTS (OPER PROHIBITION (JUMP START))

Normal is not displayed

GO TO BACKUP BOOST CONVERTER CIRCUIT

9.READ VALUE USING GTS (OPER PROHIBITION (JUMP START))
HINT:

Check whether stop and start control was prohibited based on the jump start battery condition.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Oper Prohibition (Jump Start).


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Oper Prohibition (Jump Start) Prohibition of stop and start control based on the jump start conditions Permit / Prohibit Prohibit: Engine started with the engine hood open and the ignition switch turned to START When Prohibit is displayed, the stop and start control will be prohibited until the ignition switch is turned off.
Powertrain > Stop and Start > Data List
Tester Display
Oper Prohibition (Jump Start)
50003 227 128
Result:
Proceed to
Permit is displayed
Prohibit is displayed


i.

The Data List item "Oper Permission (Jump Start)" is judged Permit or Prohibit according to the values of the following Data List items.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hood Courtesy Switch Hood courtesy switch signal ON / OFF ON: Engine hood closed
OFF: Engine hood opened
-
Oper Permission (Engine Hood Closed) Permission of stop and start control based on the engine hood open/close conditions NG / OK OK: Engine hood closed -
Powertrain > Stop and Start > Data List
Tester Display
Hood Courtesy Switch
Oper Permission (Engine Hood Closed)
50003 227 8,111
Permission Criteria:
Tester Display Conditions
Oper Prohibition (Jump Start) ON (Engine hood closed) is displayed for Hood Courtesy Switch
OK (Engine Hood Closed) is displayed for Oper Permission (Engine Hood Closed)





Permit is displayed

10.READ VALUE USING GTS (OPER PROHIBITION (MANUAL START))

Prohibit is displayed

17.READ VALUE USING GTS (HOOD COURTESY SWITCH)
10.READ VALUE USING GTS (OPER PROHIBITION (MANUAL START))
HINT:

Check whether the stop and start control was prohibited based on the manual start battery condition.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Oper Prohibition (Manual Start).


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Oper Prohibition (Manual Start) Prohibition of stop and start control based on the manual start conditions Permit / Prohibit Prohibit: During manual start When Prohibit is displayed, the stop and start control will be prohibited until the ignition switch is turned off.
Conditions for Manual Start:
·

Clutch start switch OFF or vehicle speed signal input

·

Neutral position switch OFF

·

Starter signal OFF


Powertrain > Stop and Start > Data List
Tester Display
Oper Prohibition (Manual Start)
50003 227 129
Result:
Proceed to
Permit is displayed
Prohibit is displayed


HINT:

If Prohibit is displayed, start the engine using a key.




Permit is displayed

11.READ VALUE USING GTS (OPER PERMISSION (BATTERY))

Prohibit is displayed

END (STOP AND START CONTROL PROHIBITED DUE TO MANUAL START OPERATION)

11.READ VALUE USING GTS (OPER PERMISSION (BATTERY))
HINT:

Check whether the stop and start control was prohibited based on the battery temperature battery condition.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Battery).


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Oper Permission (Battery) Permission of stop and start control based on the battery conditions NG / OK OK: Stop and start control is permitted based on battery conditions, or Active Test (forced permission) is performed -
Powertrain > Stop and Start > Data List
Tester Display
Oper Permission (Battery)
50003 227 120
Result:
Proceed to
NG is displayed
OK is displayed


i.

The Data List item "Oper Permission (Battery)" is judged OK or NG according to the values of the following Data List items.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Battery Temp (Start) Battery temperature at engine start Min.: -40°C (-40°F), Max.: 100°C (212°F) Same as temperature around battery at engine start (after engine start) -
Ambient Temp Sensor Ambient temperature Min.: -30°C (-22°F), Max.: 50°C (122°F) Close to ambient temperature -
Powertrain > Stop and Start > Data List
Tester Display
Battery Temp (Start)
Ambient Temp Sensor
50003 227 153,63
Permission Criteria:
Tester Display Battery Temperature*
Oper Permission (Battery Current) Current battery temperature is between -10°C (14°F) and 70°C (158°F)


HINT:

*: Read the Data List items "Battery Temp (Start)" and "Ambient Temp Sensor" when checking the battery temperature.





NG is displayed

12.READ VALUE USING GTS (BATTERY TEMP (START))

OK is displayed

END (CHECK OTHER STOP AND START CONTROL PERMISSION/PROHIBITION CONDITIONS)

12.READ VALUE USING GTS (BATTERY TEMP (START))
HINT:

Check the battery temperature.


a.

Enter the following menus: Powertrain / Stop and Start / Data List.


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Battery Temp (Start) Battery temperature at engine start Min.: -40°C (-40°F), Max.: 100°C (212°F) Same as temperature around battery at engine start (after engine start) -
Ambient Temp Sensor Ambient temperature Min.: -30°C (-22°F), Max.: 50°C (122°F) Close to ambient temperature -
Powertrain > Stop and Start > Data List
Tester Display
Battery Temp (Start)
Ambient Temp Sensor
50003 227 153,63
Result:
Proceed to
Battery temperature is as specified
Battery temperature is not as specified


HINT:

If the battery temperature is not as specified, leave the battery under room temperature conditions until its temperature becomes as specified.




Battery temperature is as specified

13.READ VALUE USING GTS (OPER PERMISSION (BATTERY))

Battery temperature is not as specified

END (STOP AND START CONTROL PROHIBITED DUE TO ABNORMAL BATTERY TEMPERATURE)

13.READ VALUE USING GTS (OPER PERMISSION (BATTERY))
HINT:

Check whether stop and start control was prohibited based on the alternator status battery condition.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Battery).


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Oper Permission (Battery) Permission of stop and start control based on the battery conditions NG / OK OK: Stop and start control is permitted based on battery conditions, or Active Test (forced permission) is performed -
Powertrain > Stop and Start > Data List
Tester Display
Oper Permission (Battery)
50003 227 120
Result:
Proceed to
NG is displayed
OK is displayed


i.

The Data List item "Oper Permission (Battery)" is judged OK or NG according to the values of the following Data List items.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Alternator Status Alternator power generation status Normal / Abnormal Normal: Alternator operation normal -
Powertrain > Stop and Start > Data List
Tester Display
Alternator Status
50003 227 298
Permission Criteria:
Tester Display Conditions
Oper Permission (Battery) Normal is displayed for Alternator Status (Alternator is generating power)
Charge indicator light is off when the engine is running (Alternator is generating power)





NG is displayed

14.READ VALUE USING GTS (ALTERNATOR STATUS)

OK is displayed

END (CHECK OTHER STOP AND START CONTROL PERMISSION/PROHIBITION CONDITIONS)

14.READ VALUE USING GTS (ALTERNATOR STATUS)
HINT:

Check the power generation status of the alternator.


a.

Start the engine and allow it to idle.


b.

Enter the following menus: Powertrain / Stop and Start / Data List / Alternator Status.


c.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Alternator Status Alternator power generation status Normal / Abnormal Normal: Alternator operation normal -
Powertrain > Stop and Start > Data List
Tester Display
Alternator Status
50003 227 298
Result:
Proceed to
Normal is displayed
Abnormal is displayed




Normal is displayed

15.READ VALUE USING GTS (OPER PERMISSION (BATTERY))

Abnormal is displayed

15.READ VALUE USING GTS (OPER PERMISSION (BATTERY))
HINT:

Check whether stop and start control was prohibited based on the idling stop rate battery condition.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Battery).


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Oper Permission (Battery) Permission of stop and start control based on the battery conditions NG / OK OK: Stop and start control is permitted based on battery conditions, or Active Test (forced permission) is performed -
Powertrain > Stop and Start > Data List
Tester Display
Oper Permission (Battery)
50003 227 120
Result:
Proceed to
NG is displayed
OK is displayed


i.

The Data List item "Oper Permission (Battery)" is judged OK or NG according to the values of the following Data List items.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Idling Stop Rate Rate of the idling stop time to the entire ignition switch ON time Min.: 0%, Max.: 100% - -
Powertrain > Stop and Start > Data List
Tester Display
Idling Stop Rate
50003 227 176
Permission Criteria:
Tester Display Idling Stop Rate
Oper Permission (Battery) 39% or less


HINT:

When the idling stop rate exceeds 40%, stop and start control is permitted when the rate drops to 37% or less.





NG is displayed

16.READ VALUE USING GTS (IDLING STOP RATE)

OK is displayed

END (CHECK OTHER STOP AND START CONTROL PERMISSION/PROHIBITION CONDITIONS)

16.READ VALUE USING GTS (IDLING STOP RATE)
HINT:

Check the idling stop rate.


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Idling Stop Rate.


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Idling Stop Rate Rate of the idling stop time to the entire ignition switch ON time Min.: 0%, Max.: 100% - -
Powertrain > Stop and Start > Data List
Tester Display
Idling Stop Rate
50003 227 176
Result:
Proceed to
40% or higher
39% or less


HINT:

When the idling stop rate exceeds 40%, turn the ignition switch off and then start the engine again. If NG is still displayed for the Data List item "Oper Permission (Battery)", the battery may be discharged or deteriorated. Check the battery condition and recharge or replace the battery.




40% or higher

END (STOP AND START CONTROL PROHIBITED DUE TO HIGH IDLING STOP RATE (40% OR MORE))

39% or less

END (CHECK BATTERY CONDITION AND RECHARGE OR REPLACE BATTERY)

17.READ VALUE USING GTS (HOOD COURTESY SWITCH)
HINT:

Check the engine hood courtesy switch (hood lock assembly).


a.

Enter the following menus: Powertrain / Stop and Start / Data List / Hood Courtesy Switch.


b.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hood Courtesy Switch Hood courtesy switch signal ON / OFF ON: Engine hood closed
OFF: Engine hood opened
-
Powertrain > Stop and Start > Data List
Tester Display
Hood Courtesy Switch
50003 227 8
Result:
Proceed to
OK
NG


HINT:

When the result is OK, the engine may have been started with the engine hood open to perform a jump start. Close the engine hood and start the engine again.




OK

END (STOP AND START CONTROL PROHIBITED DUE TO ENGINE START WITH ENGINE HOOD OPEN)

NG

GO TO ENGINE HOOD COURTESY SWITCH CIRCUIT

18.READ VALUE USING GTS (INTEGRATED CURRENT)
HINT:

Judge the battery condition based on the integrated current value.


a.

Start the engine and allow it to idle.


b.

Enter the following menus: Powertrain / Stop and Start / Data List / Integrated Current.


c.

Check the following items on the GTS display.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Integrated Current Battery integrated current Min.: -268434.45 A-sec, Max.: 268435.45 A-sec Differs according to the vehicle condition (charge / discharge conditions) -
Powertrain > Stop and Start > Data List
Tester Display
Integrated Current
50003 227 65
i.

Judge whether the Data List item "Integrated Current" is OK or NG according to the following table.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Battery Temp (Start) Battery temperature at engine start Min.: -40°C (-40°F), Max.: 100°C (212°F) Same as temperature around battery at engine start (after engine start) -
Idle Engine idling status ON / OFF ON: Accelerator pedal fully released
OFF: Accelerator pedal depressed
This is sent from the ECM.
Battery Current Battery current Min.: 0 A, Max.: 124.99 A - -
Ambient Temp Sensor Ambient temperature Min.: -30°C (-22°F), Max.: 50°C (122°F) Close to ambient air temperature -
Integrated Current Battery integrated current Min.: -268434.45 A-sec, Max.: 268435.45 A-sec Differs according to the vehicle condition (charge / discharge conditions) -
Powertrain > Stop and Start > Data List
Tester Display
Battery Temp (Start)
Idle
Battery Current
Ambient Temp Sensor
Integrated Current
50003 227 153,20,60,63,65
Standard Integrated Current Value:
Battery Temperature Tester Display Integrated Current Proceed to
-1°C (30.2°F) or higher, or 65°C (149°F) or less Integrated Current Below -5299 A-sec A
-1°C (30.2°F) or higher, or 65°C (149°F) or less Below 0 A-sec A
Below -1°C (30.2°F) or -15°C (5°F) or higher, or 65°C (149°F) or higher, or 75°C (167°F) or less
Below -15°C (5°F) or higher than 75°C (167°F) - B


Cause and Action to be Taken:
Result Cause Action to be Taken
A Integrated current value is limited for the stop and start control due to discharge or deterioration of the battery Check the battery condition and recharge or replace the battery
B Integrated current value is limited for stop and start control due to battery temperature (too high/low) Leave the battery under room temperature conditions until its temperature becomes as specified. Then check the battery condition and recharge or replace the battery.


·

After recharging the battery, initialize the integrated current value* and drive the vehicle until stop and start control operation is permitted (approximately 15 to 40 minutes).

*: Disconnect the cables from the battery, wait for 30 seconds or more and then reconnect the cables.

·

When the battery sensor current value is normal, recharge or replace the battery




Result:
Proceed to
NEXT



NEXT

END (RECHARGE OR REPLACE BATTERY)