Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)
RM3090E _58 Vehicle Interior _008788 SEAT BELT _0049193 SEAT BELT WARNING SYSTEM(w/o Occupant Classification System) J

SEAT BELT  SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

When the ignition switch is turned to ON, the main body ECU (multiplex network body ECU) transmits front seat inner belt LH*1 (or RH*2) state signals to the combination meter assembly through the CAN. If the driver side seat belt is not fastened, the combination meter assembly blinks the front seat belt warning light. If the seat belt is fastened, the warning light goes off.

*1: for LHD

*2: for RHD

HINT:

The front seat belt warning light on the combination meter assembly is used for both the driver side seat and front passenger side seat.


WIRING DIAGRAM

C279307E01
0.51,4.427 2.406,4.615 1.896,0.188 10 false : CAN Communication Line 0.167,3.781 2.063,3.969 1.896,0.188 10 false *1: for LHD 0.177,2.552 3.25,2.75 3.073,0.198 10 false Front Seat Inner Belt Assembly LH 0.156,4.115 2.052,4.302 1.896,0.188 10 false *2: for RHD 1.115,3.771 3.01,3.958 1.896,0.188 10 false *3: for Power Seat 1.125,4.104 3.021,4.292 1.896,0.188 10 false *4: for Manual Seat 0.177,2.385 2.073,2.573 1.896,0.188 10 false N15*1, *3, N35*1,*4 0.177,2.948 2.073,3.135 1.896,0.188 10 false M17*2, *3, M31*2,*4 0.188,3.104 3.5,3.313 3.313,0.208 10 false Front Seat Inner Belt Assembly RH 2.938,2.51 4.604,2.927 1.667,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 2.417,0.833 2.708,1 0.292,0.167 10 false 3E 2.938,2.344 3.135,2.51 0.198,0.167 10 false A 2.083,0.833 2.375,1 0.292,0.167 10 false 3C 1.469,0.76 1.76,0.927 0.292,0.167 10 false 3 2.375,0.656 2.75,0.833 0.375,0.177 10 false 34*1 2.042,0.656 2.417,0.833 0.375,0.177 10 false 40*2 2.75,0.74 2.99,0.927 0.24,0.188 10 false 18 5.333,2.333 5.625,2.5 0.292,0.167 10 false G16 5.323,2.51 7.156,2.75 1.833,0.24 10 false Combination Meter Assembly 1.906,1.313 2.99,1.979 1.083,0.667 10 false Instrument Panel Junction Block Assembly 1.479,1.5 1.771,1.667 0.292,0.167 10 false 2 3.063,0.844 3.75,1.104 0.688,0.26 10 false DBKL

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses a CAN communication system. Inspect the communication function by following How to Proceed with troubleshooting.

Troubleshoot the seat belt warning system after confirming that the communication system is functioning properly.



PROCEDURE

1.READ VALUE USING GTS (D SEAT BELT BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver side seat belt buckle switch ON/OFF ON: Driver side seat belt fastened
OFF: Driver side seat belt unfastened
-
Body Electrical > Main Body > Data List
Tester Display
D Seat Buckle SW
50003 123 14

Result:
Result Proceed to
ON or OFF is displayed on the GTS screen according to the driver side seat belt condition A
ON or OFF is not displayed normally on the GTS screen according to the driver side seat belt condition B



A

2.PERFORM ACTIVE TEST USING GTS (DRIVER SIDE SEAT BELT)

B

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY
2.PERFORM ACTIVE TEST USING GTS (DRIVER SIDE SEAT BELT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Driver Side Seat Belt Front seat belt warning light OFF/ON The current customize setting is displayed.
Body Electrical > Combination Meter > Active Test
Tester Display
Driver Side Seat Belt
50004 122 12
OK:

The front seat belt warning light on the combination meter assembly operates normally.



Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY
a.

Remove the front seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the front seat inner belt assembly.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the N15*1,*3, N35*1,*4, M17*2,*3 or M31*2,*4 front seat inner belt assembly connector.

*1: for LHD

*2: for RHD

*3: for Power Seat

*4: for Manual Seat



b.

Disconnect the A main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD, for Power Seat:
Tester Connection Condition Specified Condition
N15-3 - A-18 (DBKL) Always Below 1 Ω
N15-2 - Body ground
N15-3 - Body ground Always 10 kΩ or higher

for LHD, for Manual Seat:
Tester Connection Condition Specified Condition
N35-3 - A-18 (DBKL) Always Below 1 Ω
N35-2 - Body ground
N35-3 - Body ground Always 10 kΩ or higher

for RHD, for Power Seat:
Tester Connection Condition Specified Condition
M17-3 - A-18 (DBKL) Always Below 1 Ω
M17-2 - Body ground
M17-3 - Body ground Always 10 kΩ or higher

for RHD, for Manual Seat:
Tester Connection Condition Specified Condition
M31-3 - A-18 (DBKL) Always Below 1 Ω
M31-2 - Body ground
M31-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

5.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the N15*1,*3, N35*1,*4, M17*2,*3 or M31*2,*4 front seat inner belt assembly connector.

*1: for LHD

*2: for RHD

*3: for Power Seat

*4: for Manual Seat



b.

Disconnect the 3E*1 or 3C*2 instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD, for Power Seat:
Tester Connection Condition Specified Condition
N15-3 - 3E-34 (DBKL) Always Below 1 Ω

for LHD, for Manual Seat:
Tester Connection Condition Specified Condition
N35-3 - 3E-34 (DBKL) Always Below 1 Ω

for RHD, for Power Seat:
Tester Connection Condition Specified Condition
M17-3 - 3C-40 (DBKL) Always Below 1 Ω

for RHD, for Manual Seat:
Tester Connection Condition Specified Condition
M31-3 - 3C-40 (DBKL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR