Home › Engine / Hybrid System › 3ZR-FE ENGINE CONTROL › SFI SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008380 3ZR-FE ENGINE CONTROL _0050132 SFI SYSTEM C

3ZR-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. below 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is low. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A115539E30
2.979,1.229 3.292,0.844 false 2.688,1.792 3.302,1.792 false 2.583,2.417 3.24,2.385 false 2.677,2.719 3.26,2.854 false 1.094,2.917 1.333,2.917 false 2.667,1.458 2.667,1.531 false 2.781,1.469 3.219,1.26 3.219,1.26 2.656,1.385 false 2.146,0.635 3.292,0.958 1.146,0.323 10 Atmosphere 3.344,0.74 4.083,0.938 0.74,0.198 10 Housing 3.281,1.188 4.698,1.458 1.417,0.271 10 Platinum Electrode 4.208,0.771 5.198,1.052 0.99,0.281 10 Output Voltage 5.208,0.958 6.604,1.292 1.396,0.333 10 Ideal Air Fuel Mixture 2.01,3.167 2.948,3.5 0.938,0.333 10 Exhaust Gas 3.344,1.698 4.688,2.146 1.344,0.448 10 Solid Electrolyte (Zirconia Element) 3.302,2.792 4.521,3.188 1.219,0.396 10 Coating (Ceramic) 3.323,2.313 3.854,2.615 0.531,0.302 10 Heater 1.365,2.833 1.885,3.167 0.521,0.333 10 Cover 4.792,2.896 7.042,3.281 2.25,0.385 10 Richer - Air Fuel Ratio - Leaner

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) Abnormal voltage output:
During active air fuel ratio control, the following conditions (a) and (b) are met for certain period of time (2 trip detection logic)

(a) Heated oxygen sensor voltage does not decrease to below 0.21 V.

(b) Heated oxygen sensor voltage does not increase to 0.59 V or higher.


·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leakage from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

PCV valve and hose

·

Intake system


Comes on DTC stored
P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) Low voltage (open):
During active air fuel ratio control, the following conditions (a) and (b) are met for certain period of time (2 trip detection logic)

(a) Heated oxygen sensor voltage output is below 0.21 V.

(b) Target air fuel ratio rich.


·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

Gas leakage from exhaust system


Comes on DTC stored
P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) High voltage (short):
During active air fuel ratio control, the following conditions (a) and (b) are met for certain period of time (2 trip detection logic)

(a) Heated oxygen sensor voltage output is higher than 0.59 V.

(b) Target air fuel ratio lean.


·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

Active Air-fuel Ratio Control

The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).

Active air fuel ratio control is performed for approximately 30 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Voltage Output of Heated Oxygen Sensor (DTC P0136)

While the ECM is performing active air fuel ratio control, the air fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the heated oxygen sensor voltage does not decrease to below 0.21 V and does not increase to 0.59 V or higher during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136.

A152942E42
0.068,0.052 4.982,0.26 4.914,0.208 10 Heated Oxygen Sensor Circuit Malfunction (P0136: Abnormal Voltage) 4.724,1.259 5.416,1.432 0.693,0.173 10 Operation 4.237,0.755 5.924,0.911 1.688,0.156 10 Approximately 30 seconds 3.335,1.568 3.853,1.752 0.518,0.184 10 Normal 2.178,1.357 2.522,1.534 0.344,0.177 10 OFF 2.087,2.126 2.549,2.296 0.462,0.17 10 0.59 V 2.087,2.892 2.549,3.069 0.462,0.177 10 0.21 V 3.166,2.541 3.85,2.725 0.684,0.184 10 Abnormal 2.97,2.091 3.152,1.624 false 3.152,1.624 3.292,1.624 false 2.794,2.303 2.921,2.604 false 2.921,2.604 3.11,2.604 false 0.052,1.329 1.917,1.52 1.865,0.191 10 Active air fuel ratio control 0.051,2.528 2.016,2.719 1.964,0.191 10 Heated oxygen sensor voltage


Open or Short in Heated Oxygen Sensor Circuit (DTC P0137 or P0138)

During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean. If the heated oxygen sensor has an open or short circuit, or the voltage output of the sensor noticeably decreases, the OSC indicated an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air fuel ratio control, when the target air fuel ratio is rich and the heated oxygen sensor voltage output is below 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137. When the target air fuel ratio is lean and the voltage output is higher than 0.59 V (rich) during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormally high and stores DTC P0138.

*: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated, based on the calculated OSC value (Click here Engine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>P0420).

A152992E42
5.823,3.792 6.021,4.031 false 4.292,2.052 4.448,1.729 false 4.448,1.729 4.594,1.729 false 5.302,2.406 5.448,1.719 false 5.448,1.719 5.625,1.719 false 5.677,3.021 5.844,2.563 false 5.844,2.563 6,2.563 false 5.729,6.583 5.969,6.104 false 5.969,6.104 6.104,6.104 false 0.063,0.052 3.76,0.26 3.698,0.208 10 Heated Oxygen Sensor Circuit Low Voltage (P0137: Open) 0.281,1.219 1.281,1.563 1,0.344 10 Active Air Fuel Ratio Control 0.281,3.208 1.271,3.563 0.99,0.354 10 Heated Oxygen Sensor Voltage 0.281,2.083 1.656,2.281 1.375,0.198 10 Target Air Fuel Ratio 1.979,2.031 2.927,2.396 0.948,0.365 10 Stoichiometric Air Fuel Level 2.781,1.313 3.146,1.51 0.365,0.198 10 Off 2.49,3.479 2.979,3.677 0.49,0.198 10 0.21 V 0.063,4.208 3.781,4.417 3.719,0.208 10 Heated Oxygen Sensor Circuit High Voltage (P0138: Short) 0.281,4.854 1.26,5.229 0.979,0.375 10 Active Air Fuel Ratio Control 0.281,6.906 1.333,7.271 1.052,0.365 10 Heated Oxygen Sensor Voltage 0.281,5.74 1.698,5.938 1.417,0.198 10 Target Air Fuel Ratio 2.094,5.667 3.042,6.031 0.948,0.365 10 Stoichiometric Air Fuel Level 2.74,4.938 3.094,5.135 0.354,0.198 10 Off 3.958,0.396 5.635,0.667 1.677,0.271 10 Approximately 30 seconds 4.521,1.281 5.281,1.479 0.76,0.198 10 Operation 4.479,4.896 5.177,5.094 0.698,0.198 10 Operation 4.708,5.708 5.104,5.906 0.396,0.198 10 Lean 4.656,1.646 5.219,1.844 0.563,0.198 10 Normal 6.146,6.01 6.833,6.208 0.688,0.198 10 Abnormal 5.688,1.625 6.333,1.823 0.646,0.198 10 Abnormal 6.063,4.063 6.802,4.26 0.74,0.198 10 Abnormal 6.052,2.479 6.615,2.677 0.563,0.198 10 Normal 4.781,2.417 5.146,2.615 0.365,0.198 10 Rich 2.5,6.677 2.99,6.875 0.49,0.198 10 0.59 V


CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation pattern will activate the heated oxygen sensor monitor. (The catalyst monitor is performed simultaneously.) This is very useful for verifying the completion of the repair.



A264212E05
1.74,2.427 1.563,2.802 1.563,2.802 1.417,2.802 false 4.021,0.719 4.25,0.958 0.229,0.24 10 [C] 3.49,2.906 4.792,3.083 1.302,0.177 10 10 minutes or more 1.094,1.354 1.698,1.51 0.604,0.156 10 60 km/h 2.021,2.427 2.25,2.625 0.229,0.198 10 [A] 1.021,0.479 1.677,0.688 0.656,0.208 10 100 km/h 1.25,2.229 1.635,2.448 0.385,0.219 10 Idling 0.229,2.74 1.49,2.958 1.26,0.219 10 Ignition Switch ON 2.677,2.135 2.906,2.344 0.229,0.208 10 [B] 2.333,2.917 3.156,3.115 0.823,0.198 10 Warming up 5.01,3.313 5.271,3.573 0.26,0.26 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

With the shift lever in D or 4th gear or more, drive the vehicle at 60 to 100 km/h (37 to 62 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0136, P0137 or P0138.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine.

3.

Turn the GTS on.

4.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.

6.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

7.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E07
5.792,3.781 7.115,4.052 1.323,0.271 10 - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 Below 3.1 V 1.531,1.594 1.979,1.781 0.448,0.188 8 12.5% 1.479,1.833 1.927,2.021 0.448,0.188 8 -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 Below 0.4 V 4.156,1.594 4.604,1.781 0.448,0.188 8 12.5% 4.115,1.833 4.563,2.021 0.448,0.188 8 -12.5% 4.146,3.729 4.594,3.917 0.448,0.188 8 12.5% 4.104,3.917 4.552,4.104 0.448,0.188 8 -12.5% 4.104,5.958 4.552,6.146 0.448,0.188 8 -12.5% 4.104,8.021 4.552,8.208 0.448,0.188 8 -12.5% 4.156,5.74 4.604,5.927 0.448,0.188 8 12.5% 4.156,7.813 4.604,8 0.448,0.188 8 12.5% 1.49,7.813 1.938,8 0.448,0.188 8 12.5% 1.49,5.75 1.938,5.938 0.448,0.188 8 12.5% 1.5,3.677 1.948,3.865 0.448,0.188 8 12.5% 1.448,3.896 1.896,4.083 0.448,0.188 8 -12.5% 1.448,5.948 1.896,6.135 0.448,0.188 8 -12.5% 1.438,8.021 1.885,8.208 0.448,0.188 8 -12.5% 0.844,4.802 2.042,5.052 1.198,0.25 8 Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 1 0.24,4.25 0.396,4.448 0.156,0.198 10 2 0.25,6.333 0.406,6.531 0.156,0.198 10 3 0.24,8.417 0.396,8.615 0.156,0.198 10 4 0.125,0.688 0.573,0.938 0.448,0.25 10 Case 0.792,0.583 2.802,0.969 2.01,0.385 10 Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.5,0.583 5.594,1.031 2.094,0.448 10 Heated Oxygen Sensor (Sensor 2) Output Voltage 5.969,0.583 7.01,1 1.042,0.417 10 Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 - 5.802,4.031 7.125,4.469 1.323,0.438 10 - Air fuel ratio sensor heater 5.802,4.448 7.125,4.885 1.323,0.438 10 - Air fuel ratio sensor circuit 5.917,5.792 6.969,6.167 1.052,0.375 10 - Heated oxygen sensor 5.927,6.198 6.969,6.625 1.042,0.427 10 - Heated oxygen sensor heater 5.927,6.615 6.969,7.052 1.042,0.438 10 - Heated oxygen sensor circuit 5.927,7.698 6.813,8.104 0.885,0.406 10 - Fuel injector assembly 5.917,8.115 7.073,8.448 1.156,0.333 10 - Fuel pressure 5.917,8.365 6.969,9.375 1.052,1.01 10 - Gas leak from exhaust system (air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 OK 2.5,4.719 2.948,4.906 0.448,0.188 8 NG 2.552,6.865 3,7.052 0.448,0.188 8 OK 2.5,8.844 2.948,9.031 0.448,0.188 8 NG 5.167,2.708 5.615,2.896 0.448,0.188 8 OK 5.167,4.813 5.615,5 0.448,0.188 8 OK 5.135,8.854 5.583,9.042 0.448,0.188 8 NG 5.135,6.771 5.583,6.958 0.448,0.188 8 NG

·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2; and then press the graph button on the Data List view.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137 OR P0138)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
DTC P0138 is output A
DTC P0137 is output B
DTC P0136 is output C
DTC P0136, P0137 or P0138 and other DTCs are output D


HINT:

If any DTCs other than P0136, P0137 and P0138 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

B

12.CHECK FOR EXHAUST GAS LEAK

C

10.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

2.READ VALUE USING GTS (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / O2S B1S2.

Powertrain > Engine and ECT > Data List
Tester Display
O2S B1S2
50003 234 44

e.

Allow the engine to idle.


f.

Read the heated oxygen sensor output voltage while idling.

Result:
Heated Oxygen Sensor Output Voltage Proceed to
1.0 V or higher A
below 1.0 V B




A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
a.
A210693C01
1.948,1.427 2.49,1.625 true 0.948,0.844 1.5,1.021 true 0.917,1.625 1.51,1.438 true 0.073,0.094 0.26,0.281 0.188,0.188 10 *a 0.729,0.75 0.969,0.927 0.24,0.177 10 +B 0.708,1.552 0.948,1.729 0.24,0.177 10 E2 2.563,1.542 2.99,1.719 0.427,0.177 10 OX1B
*a Component without harness connected
(Heated Oxygen Sensor)


Disconnect the heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (+B) - 4 (OX1B) Always 10 kΩ or higher
1 (+B) - 3 (E2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Turn the ignition switch off and wait for 5 minutes.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B75-22 (HT1B) - B75-103 (OX1B) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
O2S B1S2
50004 234 2 35,44

f.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the GTS.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
Tester Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air fuel ratio) Alternates between higher and below 3.3 V OK
Remains at higher than 3.3 V NG
Remains at below 3.3 V


HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A285391E02
3.083,2.938 3.583,2.469 false 2.417,1.073 2.667,1.594 false 4.854,0.167 5,0.167 5,0.167 5.083,0.448 false 5.333,2.219 5.927,1.26 5.927,1.26 5.521,2.417 true 5.646,2.667 5.167,2.417 false 3.833,1.688 3.667,1.615 false 5.917,1.26 5.333,1.594 false 2.156,0.25 2.656,0.5 0.5,0.25 10 12.5% 5.979,1.177 6.938,1.625 0.958,0.448 10 Air Fuel Ratio Sensor Output 3.635,1.042 4.271,1.292 0.635,0.25 10 -12.5% 1.51,0.948 2.521,1.208 1.01,0.26 10 Malfunctioning 3.635,2.385 4.646,2.813 1.01,0.427 10 Heated Oxygen Sensor Output 3.875,1.625 4.375,1.875 0.5,0.25 10 Normal 1,1.844 1.417,2.094 0.417,0.25 10 3.3 V 1.135,2.823 1.469,3.073 0.333,0.25 10 1 V 1.125,3.354 1.458,3.604 0.333,0.25 10 0 V 5.698,2.594 6.552,2.906 0.854,0.313 10 Malfunction 3.813,0.083 4.938,0.365 1.125,0.281 10 Injection Volume



OK

6.INSPECT AIR FUEL RATIO SENSOR

NG

7.REPLACE AIR FUEL RATIO SENSOR
6.INSPECT AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel cut operation. When the sensor is normal, the sensor current will indicate below 3.6 mA in this test.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs (Click here Engine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Current B1S1.

Powertrain > Engine and ECT > Data List
Tester Display
AFS Current B1S1
50003 234 39

g.

Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



A152792E43
1.357,2.513 2.638,2.697 1.281,0.184 10 10 minutes or more 2.973,2.513 4.186,2.697 1.213,0.184 10 5 seconds or more 4.271,2.513 5.468,2.697 1.197,0.184 10 5 seconds or more 5.56,2.513 6.739,2.697 1.179,0.184 10 5 seconds or more 0.152,0.078 1.451,0.293 1.299,0.215 12 Driving Pattern: 0.455,1.379 1.114,1.594 0.658,0.215 10 60 km/h 0.527,2.139 1.062,2.342 0.536,0.203 10 0 km/h

h.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.

Standard Current:

Below 3.6 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.




Result:
Proceed to
OK
NG



OK

15.REPLACE HEATED OXYGEN SENSOR

NG

7.REPLACE AIR FUEL RATIO SENSOR
7.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (Click here Engine / Hybrid System>3ZR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here Engine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



Result:
Proceed to
NEXT



NEXT

8.PERFORM CONFIRMATION DRIVING PATTERN
8.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0138)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0138)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

e.

Input DTC: P0136 or P0138.


f.

Check that the STATUS is NORMAL. If the STATUS is INCOMPLETE, perform the driving pattern increasing the vehicle speed and using the second gear to decelerate the vehicle.

Result:
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P0136 or P0138 is output)
B




A

END

B

10.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2S B1S2.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
O2S B1S2
50004 234 2 44

f.

Change the fuel injection volume using the GTS and monitor the voltage output of heated oxygen sensor displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard Voltage:

Fluctuates between 0.4 V or less and 0.55 V or higher.



Result:
Proceed to
OK
NG



OK

11.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

12.CHECK FOR EXHAUST GAS LEAK
11.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
O2S B1S2
50004 234 2 35,44

f.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the GTS.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
Tester Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air fuel ratio) Alternates between higher and below 3.3 V OK
Remains at higher than 3.3 V NG
Remains at below 3.3 V


HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A285391E02
3.083,2.938 3.583,2.469 false 2.417,1.073 2.667,1.594 false 4.854,0.167 5,0.167 5,0.167 5.083,0.448 false 5.333,2.219 5.927,1.26 5.927,1.26 5.521,2.417 true 5.646,2.667 5.167,2.417 false 3.833,1.688 3.667,1.615 false 5.917,1.26 5.333,1.594 false 2.156,0.25 2.656,0.5 0.5,0.25 10 12.5% 5.979,1.177 6.938,1.625 0.958,0.448 10 Air Fuel Ratio Sensor Output 3.635,1.042 4.271,1.292 0.635,0.25 10 -12.5% 1.51,0.948 2.521,1.208 1.01,0.26 10 Malfunctioning 3.635,2.385 4.646,2.813 1.01,0.427 10 Heated Oxygen Sensor Output 3.875,1.625 4.375,1.875 0.5,0.25 10 Normal 1,1.844 1.417,2.094 0.417,0.25 10 3.3 V 1.135,2.823 1.469,3.073 0.333,0.25 10 1 V 1.125,3.354 1.458,3.604 0.333,0.25 10 0 V 5.698,2.594 6.552,2.906 0.854,0.313 10 Malfunction 3.813,0.083 4.938,0.365 1.125,0.281 10 Injection Volume



OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

7.REPLACE AIR FUEL RATIO SENSOR
12.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here Engine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



Result:
Proceed to
OK
NG



OK

13.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

13.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

14.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G32-2 (HT1B) - B75-22 (HT1B) Always Below 1 Ω
G32-4 (OX1B) - B75-103 (OX1B) Always Below 1 Ω
G32-3 (E2) - B75-135 (EX1B) Always Below 1 Ω
G32-2 (HT1B) or B75-22 (HT1B) - Body ground Always 10 kΩ or higher
G32-4 (OX1B) or B75-103 (OX1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE HEATED OXYGEN SENSOR
a.

Replace the heated oxygen sensor (Click here Engine / Hybrid System>3ZR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>REMOVAL).


Result:
Proceed to
NEXT



NEXT

16.PERFORM CONFIRMATION DRIVING PATTERN
16.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

e.

Input DTC: P0136, P0137 or P0138.


f.

Check that the STATUS is NORMAL. If the STATUS is INCOMPLETE, perform the driving pattern increasing the vehicle speed and using the second gear to decelerate the vehicle.

Result:
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P0136, P0137 or P0138 is output)
B


HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here Engine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




A

END

B