Home › Engine / Hybrid System › 3ZR-FE ENGINE CONTROL › SFI SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008380 3ZR-FE ENGINE CONTROL _0050132 SFI SYSTEM C

3ZR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) or more for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High When all of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.4 mph) or more.

(b) The engine speed is 1000 rpm or more.

(c) The STA signal is on.


·

Park/Neutral position switch assembly (for CVT Models)

·

Ignition switch assembly (w/o Entry and Start System)

·

ST relay circuit

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A231469E13
1.229,1.979 1.604,2.156 0.375,0.177 10 Idling 0.396,2.25 1.604,2.573 1.208,0.323 10 Ignition Switch ON 1.063,0.813 1.635,1.021 0.573,0.208 10 24 km/h 2.396,2.854 3.094,3.375 0.698,0.521 10 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 20 seconds or more 2,2.333 2.635,2.677 0.635,0.344 10 [A] 2.583,2.125 3.271,2.375 0.688,0.25 10 [B] 4.031,0.458 4.5,0.823 0.469,0.365 10 [C] 4.906,3.344 5.344,3.563 0.438,0.219 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds or more [B].

8.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0617.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A298879E01
0.115,0.125 2.396,0.396 2.281,0.271 12 false w/o Entry and Start System: 3.24,1.948 5.115,2.365 1.875,0.417 10 false Park/Neutral Position Switch Assembly*2 1.177,1.448 1.406,1.635 0.229,0.188 10 false G4 1.594,1.021 2.021,1.219 0.427,0.198 10 false AM2 2.188,1.021 2.615,1.219 0.427,0.198 10 false ST2 0.5,2.281 0.927,2.479 0.427,0.198 10 false AM2 4.594,1.396 4.854,1.563 0.26,0.167 10 false 4 2.563,1.021 2.792,1.208 0.229,0.188 10 false 2 5.813,1.135 6.375,1.344 0.563,0.208 10 false NSW*2 5.802,3.573 6.365,3.781 0.563,0.208 10 false STA 5.417,1.135 5.698,1.333 0.281,0.198 10 false B75 5.417,3.698 5.698,3.896 0.281,0.198 10 false A62 5.458,0.927 5.74,1.125 0.281,0.198 10 false 63 5.469,3.49 5.75,3.688 0.281,0.198 10 false 22 3.229,1.781 3.51,1.99 0.281,0.208 10 false B36 1.188,1.604 3.125,1.906 1.938,0.302 10 false Ignition Switch Assembly 3.323,2.99 3.667,3.198 0.344,0.208 10 false A4*3 3.323,3.167 3.667,3.375 0.344,0.208 10 false F2*4 3.313,3.344 5.458,3.573 2.146,0.229 10 false Clutch Start Switch Assembly*1 3.469,4.49 3.75,4.698 0.281,0.208 10 false ST 1.594,3.896 1.875,4.104 0.281,0.208 10 false ST 0.667,6.729 1.229,6.927 0.563,0.198 10 false Battery 1.323,6.646 2.552,6.927 1.229,0.281 10 false Starter Assembly 1.292,5.844 1.573,6.052 0.281,0.208 10 false C6 2.01,5.438 2.292,5.646 0.281,0.208 10 false B6 4.604,2.604 4.833,2.792 0.229,0.188 10 false 2 3.229,4.031 3.458,4.219 0.229,0.188 10 false 2 1.417,1.042 1.677,1.208 0.26,0.167 10 false 4 3.667,1.396 3.927,1.563 0.26,0.167 10 false 9 3.667,2.604 3.927,2.771 0.26,0.167 10 false 1 3.219,4.979 3.479,5.146 0.26,0.167 10 false 1 2.688,4.031 2.917,4.219 0.229,0.188 10 false 5 2.688,4.969 2.917,5.156 0.229,0.188 10 false 3 2.323,5.427 2.583,5.594 0.26,0.167 10 false 1 1.333,5.646 1.594,5.813 0.26,0.167 10 false 1 3.979,6.01 6.125,6.24 2.146,0.229 10 false *1: for Manual Transaxle Models 6.167,4.927 6.729,5.135 0.563,0.208 10 false ECM 3.979,6.344 6.125,6.573 2.146,0.229 10 false *2: for CVT Models 3.979,6.667 6.125,6.896 2.146,0.229 10 false *3: for LHD 3.979,7 6.125,7.229 2.146,0.229 10 false *4: for RHD 4.385,1.396 4.646,1.563 0.26,0.167 10 false B 3.885,1.396 4.146,1.563 0.26,0.167 10 false L 5.167,1.042 5.385,1.24 0.219,0.198 10 false *2 4.833,1.396 5.052,1.594 0.219,0.198 10 false *2 3.333,1.406 3.552,1.604 0.219,0.198 10 false *2 4.813,2.604 5.031,2.802 0.219,0.198 10 false *1 3.302,2.625 3.521,2.823 0.219,0.198 10 false *1 0.51,4.771 1.271,4.99 0.76,0.219 10 false FL MAIN

A298880E01
0.115,0.115 2.177,0.344 2.063,0.229 12 false w/ Entry and Start System: 3.135,2.01 3.573,2.229 0.438,0.219 10 false B36 0.219,2.292 1.729,2.969 1.51,0.677 10 false Certification ECU (Smart Key ECU Assembly) 5.781,0.875 6.219,1.094 0.438,0.219 10 false NEO 5.802,1.333 6.438,1.542 0.635,0.208 10 false NSW*2 1.313,0.885 1.75,1.104 0.438,0.219 10 false NE 1.24,1.729 1.677,1.948 0.438,0.219 10 false STA 1.167,1.323 1.604,1.542 0.438,0.219 10 false STAR 5.792,4.167 6.229,4.385 0.438,0.219 10 false STA 5.427,0.875 5.865,1.094 0.438,0.219 10 false A62 5.427,4.281 5.865,4.5 0.438,0.219 10 false A62 5.427,1.323 5.865,1.542 0.438,0.219 10 false B75 0.219,2.115 0.656,2.333 0.438,0.219 10 false G82 3.125,2.188 4.927,2.792 1.802,0.604 10 false Park/Neutral Position Switch Assembly*2 3.083,3.719 5.344,3.948 2.26,0.229 10 false Clutch Start Switch Assembly*1 3.094,3.333 3.531,3.552 0.438,0.219 10 false A4*3 3.094,3.521 3.531,3.74 0.438,0.219 10 false F2*4 0.417,4.271 0.854,4.49 0.438,0.219 10 false ST 2.979,4.958 3.417,5.177 0.438,0.219 10 false ST 0.573,6.865 1.063,7.094 0.49,0.229 10 false Battery 1.135,6.917 2.313,7.167 1.177,0.25 10 false Starter Assembly 6.167,5.49 6.604,5.708 0.438,0.219 10 false ECM 1.073,6.104 1.51,6.323 0.438,0.219 10 false C6 1.802,5.885 2.24,6.104 0.438,0.219 10 false B6 1.125,5.917 1.563,6.135 0.438,0.219 10 false 1 2.083,5.875 2.521,6.094 0.438,0.219 10 false 1 2.729,5.448 3.167,5.667 0.438,0.219 10 false 1 2.719,4.479 3.156,4.698 0.438,0.219 10 false 2 2.198,5.448 2.635,5.667 0.438,0.219 10 false 3 2.219,4.479 2.656,4.698 0.438,0.219 10 false 5 3.49,2.938 3.927,3.156 0.438,0.219 10 false 1 4.458,2.927 4.896,3.146 0.438,0.219 10 false 2 4.438,1.615 4.875,1.833 0.438,0.219 10 false 4 3.5,1.604 3.938,1.823 0.438,0.219 10 false 9 3.719,1.615 3.99,1.833 0.271,0.219 10 false L 4.219,1.625 4.49,1.844 0.271,0.219 10 false B 1.688,1.594 2.125,1.813 0.438,0.219 10 false 7 1.688,1.188 2.125,1.406 0.438,0.219 10 false 5 1.646,0.74 2.083,0.958 0.438,0.219 10 false 16 5.469,0.677 5.906,0.896 0.438,0.219 10 false 30 5.469,1.125 5.906,1.344 0.438,0.219 10 false 63 5.479,4.073 5.917,4.292 0.438,0.219 10 false 22 3.594,6.219 5.802,6.448 2.208,0.229 10 false *1: for Manual Transaxle Models 3.594,6.833 4.76,7.052 1.167,0.219 10 false *3: for LHD 3.594,6.521 5.802,6.75 2.208,0.229 10 false *2: for CVT Models 3.583,7.146 4.75,7.365 1.167,0.219 10 false *4: for RHD 5.219,1.219 5.458,1.417 0.24,0.198 10 false *2 4.792,1.625 5.031,1.823 0.24,0.198 10 false *2 3.156,1.625 3.396,1.823 0.24,0.198 10 false *2 3.146,2.958 3.385,3.156 0.24,0.198 10 false *1 4.792,2.979 5.031,3.177 0.24,0.198 10 false *1 0.438,5.281 1.281,5.542 0.844,0.26 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

NOTICE:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF (Starter signal off) A
ON (Starter signal on)
(for CVT Models)
B
ON (Starter signal on)
(w/ Entry and Start System and for Manual Transaxle Models)
C
ON (Starter signal on)
(w/o Entry and Start System and for Manual Transaxle Models)
D



A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

D

7.INSPECT IGNITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.


Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG (for 2WD) C
NG (for 4WD/AWD) D



A

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

B

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

D

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (park/neutral position switch assembly - ST relay - ECM - certification ECU (smart key ECU assembly)).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs (Click here Engine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read the DTCs.

Result:
Result Proceed to
DTC P617 is output A
DTC is not output B




A

B

END

5.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (park/neutral position switch assembly - ST relay - ECM).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
6.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (clutch start switch assembly - ST relay - ECM - certification ECU (smart key ECU assembly)).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
7.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (Click here Engine / Hybrid System>3ZR-FE STARTING>IGNITION SWITCH>INSPECTION).


Result:
Proceed to
OK
NG



OK

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

REPLACE IGNITION SWITCH ASSEMBLY

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (clutch start switch assembly - ST relay - ECM).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)