Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING
RM3090E _59 Vehicle Exterior _008798 EXTERIOR PANELS / TRIM _0050167 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 75792 1.INSTALL DOOR WINDOW FRAME MOULDING CLIP

a.

Attach the 2 claws to install the door window frame moulding clip.


Hide 75076 2.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH

HINT:

When installing the rear door outside moulding, heat the rear door panel and rear door outside moulding using a heatlight.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Rear Door Outside Moulding 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the rear door panel and rear door outside moulding excessively.


a.

Clean the rear door panel surface.

i.

Using a heat light, heat the rear door panelsurface.


ii.

Remove the double-sided tape from the rear door panel surface.


iii.

Wipe off any tape adhesive residue withcleaner.



b.

Install a new rear door outside moulding sub-assembly LH.

i.

Using a heat light, heat a new rear door outside moulding sub-assembly LH and the rear door panel surface.


ii.

Remove the peeling paper from the face of the rear door outside moulding sub-assembly LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.
B340213C01
0.479,0.552 0.771,0.552 true 0.708,1.354 1,1.354 true 1.313,0.25 1.313,0.135 1.313,0.135 1.5,0.135 true 1.479,1.635 1.479,1.458 1.479,1.458 1.667,1.458 true 1.531,0.052 1.844,0.208 0.313,0.156 10 *1 0.333,0.469 0.646,0.625 0.313,0.156 10 *2 1.021,1.271 1.333,1.427 0.313,0.156 10 *2 1.688,1.375 2,1.531 0.313,0.156 10 *1
*1 Protective Tape
*2 Double-sided Tape


Attach the clip and double-sided tape to install the rear door outside moulding sub-assembly LH.

HINT:

Press the rear door outside moulding sub-assembly LH firmly to install it.




Hide 67872 3.INSTALL REAR DOOR WEATHERSTRIP LH

a.

Install the rear door weatherstrip LH.


Hide 75740 4.INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

Hide 68104 5.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 68124B 6.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

Hide 67408E 7.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68152C 8.INSTALL REAR DOOR GLASS RUN LH

Hide 67842E 9.INSTALL REAR DOOR SERVICE HOLE COVER LH

Hide 67604 10.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 69284D 11.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

Hide 74646A 12.INSTALL DOOR ASSIST GRIP COVER LH

Hide 13.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION