Home › Engine / Hybrid System › 1AD-FTV COOLING › WATER PUMP › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008374 1AD-FTV COOLING _0050229 WATER PUMP A

1AD-FTV COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 16100 1.INSTALL ENGINE WATER PUMP ASSEMBLY

a.

Remove the adhesive from the threads of the bolt and the bolt hole of the timing chain cover sub-assembly.


b.
A196725

Install a new gasket to the timing chain cover sub-assembly so that the protrusions indicated by the arrows in the illustration are aligned.


c.
A300906N01
0.594,0.844 0.75,1.042 0.156,0.198 10 true A 2.76,0.698 2.917,0.896 0.156,0.198 10 true B 2.823,1.792 2.979,1.99 0.156,0.198 10 true B 2.104,0.083 2.26,0.281 0.156,0.198 10 true C 0.813,0.073 0.969,0.271 0.156,0.198 10 true C 0.792,1.802 0.948,2 0.156,0.198 10 true C 2.229,1.969 2.385,2.167 0.156,0.198 10 true C

Apply adhesive to 2 or 3 threads of the bolt labeled A.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Standard Bolt Length:
Item Specified Condition
Bolt A and C 45 mm (1.77 in.)
Bolt B 30 mm (1.18 in.)



d.
A300907

Install the engine water pump assembly with the 2 bolts indicated by the arrows in the illustration.

Torque:
23 N*m (229 kgf*cm, 17 ft.*lbf)


e.
A300921

Install the 5 bolts.

Torque:
23 N*m (229 kgf*cm, 17 ft.*lbf)


Hide 16604 2.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

a.

Install the No. 2 idler pulley sub-assembly and No. 2 idler pulley cover plate with the bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 16603 3.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16649B 4.INSTALL IDLER PULLEY COVER PLATE

Hide 12341 5.INSTALL ENGINE MOUNTING SPACER

a.

Install the engine mounting spacer with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 12305 6.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

a.

Install the engine mounting insulator sub-assembly RH with the 5 bolts and nut.

Torque:
Bolt and Nut : 95 N*m (969 kgf*cm, 70 ft.*lbf)


b.

Remove the jack.


c.

Tighten the 4 bolts and 2 nuts to the front engine mounting insulator and rear engine mounting insulator.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


d.
A297535

Install the nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 16361A 8.INSTALL FAN AND GENERATOR V BELT

Hide 51217A 9.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

Hide 16470 10.INSTALL RADIATOR RESERVOIR ASSEMBLY

Hide 51443 14.INSTALL REAR ENGINE UNDER COVER RH

Hide 51441 15.INSTALL NO. 1 ENGINE UNDER COVER