Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY
RM3090E _52 Drivetrain _008761 DRIVE SHAFT / PROPELLER SHAFT _0050237 REAR DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 41336K 1.INSTALL REAR DRIVE SHAFT DUST COVER LH

C129497
0.917,1.313 0.75,1 0.75,1 0.583,1 true 0.25,0.917 0.563,1.083 0.313,0.167 10 SST

a.

Using SST and a press, install a new rear drive shaft dust cover LH.

SST
09527-10011  

NOTICE:
·

The rear drive shaft dust cover LH should be installed completely.

·

Be careful not to damage the rear drive shaft dust cover LH.




Hide 2.INSTALL OUTBOARD JOINT BOOT

C127681C05
2.094,0.479 1.896,0.479 1.896,0.479 1.76,0.75 false 2.146,0.406 2.833,0.573 0.688,0.167 10 false *a
*a Protective Tape


a.

Before installing the outboard joint boot, wrap the splines of the rear drive outboard joint shaft assembly with protective tape to prevent the outboard joint boot from being damaged.


b.

Install new parts to the rear drive outboard joint shaft assembly in the following order.

i.

Rear No. 2 drive shaft outboard joint boot clamp


ii.

Outboard joint boot


iii.

Rear drive shaft outboard joint boot clamp



c.

Install the outboard joint boot so that it is between the rear No. 2 drive shaft outboard joint boot clamp and rear drive outboard joint shaft assembly.


d.

Temporarily install the rear drive shaft outboard joint boot clamp to the outboard joint boot.


e.

Pack the rear drive outboard joint shaft assembly and outboard joint boot with grease from the boot kit.

Standard Grease Capacity:

55 to 65 g (2.0 to 2.2 oz)



Hide 42346F 3.INSTALL REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

a.
C277141

Using a screwdriver, install the rear No. 2 drive shaft outboard joint boot clamp LH as shown in the illustration.

NOTICE:

Be careful not to damage the outboard joint boot.



Hide 42346D 4.INSTALL REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP LH

a.

Install the rear drive shaft outboard joint boot clamp LH onto the outboard joint boot.


b.
C277142
1.146,1.615 1.354,1.615 1.354,1.615 1.75,0.99 true 2.271,1.719 2.583,1.917 0.313,0.198 10 *a 2.188,0.083 2.5,0.281 0.313,0.198 10 *b 0.823,1.521 1.135,1.719 0.313,0.198 10 SST
*a Turn
*b Hold


Place SST onto the rear drive shaft outboard joint boot clamp LH.

SST
09521-24010  


c.

Tighten SST so that the rear drive shaft outboard joint boot clamp LH is pinched.

NOTICE:
·

Do not overtighten SST.

·

Be careful not to damage the outboard joint boot.




d.
C277143
1.75,1.375 2.177,1.865 2.177,1.865 2.365,1.865 true 2.417,1.75 2.875,1.948 0.458,0.198 10 SST

Using SST, measure the clearance of the rear drive shaft outboard joint boot clamp LH.

SST
09240-00020  

Standard Clearance:

1.2 mm (0.0472 in.) or less


NOTICE:

If the measured value exceeds the specified value, retighten the rear drive shaft outboard joint boot clamp LH.



Hide 42360D 5.INSTALL REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY LH

a.

Install new parts to the rear drive outboard joint shaft assembly LH in the following order.

i.

Rear drive shaft inboard joint boot clamp LH


ii.

Inboard joint boot


iii.

Rear No. 2 drive shaft inboard joint boot clamp LH



b.

Remove the protective tape from the rear drive outboard joint shaft assembly LH.


c.
C127694C02
1.927,1.188 2.083,1.833 2.083,1.833 1.365,1.531 true 2.083,1.833 2.25,1.833 false 2.313,1.729 3.042,1.896 0.729,0.167 10 *a
*a Matchmark


Align the matchmarks and place the beveled side of the tripod joint axial spline toward the rear drive outboard joint shaft assembly LH.


d.
C129498

Using a brass bar and hammer, tap the tripod joint onto the rear drive outboard joint shaft assembly LH.

NOTICE:
·

Do not tap the rollers.

·

Be sure to install the tripod joint in the correct direction.




e.
C127695

Using a snap ring expander, install a new snap ring.


f.

Pack the rear drive shaft inboard joint assembly LH and inboard joint boot with grease from the boot kit.

Standard Grease Capacity:

77 to 87 g (2.8 to 3.0 oz)



g.
C127646C05
1.833,0.833 1.833,0.25 true 2.167,0.396 2.167,0.25 2.167,0.25 1.417,0.25 true 1.188,0.167 1.5,0.365 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the rear drive shaft inboard joint assembly LH to the rear drive outboard joint shaft assembly LH.


Hide 6.INSTALL INBOARD JOINT BOOT

a.

Install the inboard joint boot to the rear drive shaft inboard joint assembly.


b.
C127699
1.438,1.521 1.656,1.74 0.219,0.219 10 (A)

Check that the 2 joint boots are not stretched or contracted when the rear drive shaft assembly is at the standard length.

Length (A):

733.2 mm (2.40 ft.)


NOTICE:

Keep the drive shaft assembly level during inspection.


If the boots are stretched or contracted, correct them.


Hide 42347F 7.INSTALL REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

C129501

a.

Using needle-nose pliers, install the rear No. 2 drive shaft inboard joint boot clamp LH as shown in the illustration.

NOTICE:

Be careful not to damage the inboard joint boot.



Hide 42347D 8.INSTALL REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the rear No. 2 drive shaft inboard joint boot clamp LH.