Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY
RM3090E _58 Vehicle Interior _008788 SEAT BELT _0050327 FRONT SEAT OUTER BELT ASSEMBLY N

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

HINT:

When scrapping vehicles equipped with a seat belt pretensioner or disposing of a seat belt (with a seat belt pretensioner), always deploy the seat belt pretensioner first in accordance with the procedure described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the service dept. of the distributor.


PROCEDURE

Hide 73220 1.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When Installed in Vehicle)

CAUTION:
·

Use gloves and safety glasses when handling a front seat outer belt with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt with a deployed pretensioner.

·

When deploying the seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.



NOTICE:
·

When disposing of a front seat outer belt with a pretensioner, never deploy the pretensioner in the customer's vehicle.

·

Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.

·

The seat belt pretensioner produces an exploding sound when it deploys, so perform the operation outdoors where it will not disturb local residents.

·

When deploying a front seat outer belt (with a seat belt pretensioner), perform the operation at least 10 m (33 ft.) away from the front seat outer belt.

·

Be sure to follow the procedure listed below when deploying the seat belt pretensioner.



a.
B050515
0.719,0.906 0.948,1.208 false 0.406,0.823 0.865,1.021 0.458,0.198 10 SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the seat belt pretensioner, always use the specified SST.


i.
B050511
2.26,0.896 2.615,0.896 false 2.677,0.792 2.969,1.063 0.292,0.271 10 *1
*1 Battery


Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

HINT:

At this time, do not connect the yellow connector. It will in a later step be connected to the seat belt pretensioner.



ii.
B050514
2.156,1.021 2.573,1.021 false 2.635,0.927 3,1.167 0.365,0.24 10 SST

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.




b.
B334887
1.344,0.927 1.552,0.604 true 1.542,0.448 1.854,0.646 0.313,0.198 10 *1
*1 Protective Tape


for Driver Side, Front Passenger Seat Belt without Selectable Force Limiter:

Disconnect the front seat outer belt pretensioner connector.

i.

Remove the lower center pillar garnish.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL


ii.

Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.

HINT:

Tape the screwdriver tip before use.




c.
B339093C01
1.292,0.865 1.563,0.604 false 1.583,0.458 1.896,0.615 0.313,0.156 10 *1
*1 Protective Tape


for Front Passenger Seat Belt with Selectable Force Limiter:

Using a screwdriver, pull out the 2 locking buttons in the direction shown by the arrow in the illustration to release the lock and disconnect the pretensioner connector and selectable force limiter connector as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



d.

for Driver Side, Front Passenger Seat Belt without Selectable Force Limiter:

i.

Connect SST.

SST
09082-00700  
09082-00770  

1.
B334892
2.083,1.219 2.083,0.969 false 1.333,1.802 1.333,1.552 false 1.958,1.25 2.417,1.448 0.458,0.198 10 SST 1.208,1.833 1.667,2.031 0.458,0.198 10 SST

Connect 2 SST, and then connect them to the front seat outer belt pretensioner.

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.


2.
C154370
0.688,0.875 1.094,0.875 false 1.615,1.813 1.917,2.063 0.302,0.25 10 *a 0.385,0.802 0.844,1 0.458,0.198 10 SST
*a 10 m or more


Move SST at least 10 m (33 ft.) away from the front of the vehicle.

3.

Close all the doors and windows of the vehicle.

NOTICE:

Do not damage the SST wire harness.




ii.

Deploy the front seat outer belt pretensioner.

1.

Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.

2.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.

3.

Press the SST deployment switch to deploy the front seat outer belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.





e.

for Front Passenger Seat Belt with Selectable Force Limiter:

i.

Connect SST.

SST
09082-00700  
09082-00770  

1.
B341367
1.292,1.771 1.292,1.51 false 2.083,1.208 2.083,0.948 false 1.177,1.844 1.635,2.042 0.458,0.198 10 SST 1.958,1.24 2.417,1.438 0.458,0.198 10 SST

Connect 2 SST, and then connect them to the front seat outer belt pretensioner.

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.


2.
C154370
0.688,0.875 1.094,0.875 false 1.615,1.813 1.917,2.063 0.302,0.25 10 *a 0.385,0.802 0.844,1 0.458,0.198 10 SST
*a 10 m or more


Move SST at least 10 m (33 ft.) away from the front of the vehicle.

3.

Close all the doors and windows of the vehicle.

NOTICE:

Do not damage the SST wire harness.




ii.

Deploy the front seat outer belt pretensioner.

1.

Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.

2.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.

3.

Press the SST deployment switch to deploy the front seat outer belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.




iii.

Disconnect the SST.

CAUTION:

The front seat outer belt becomes very hot when the front seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.



iv.

Connect SST.

1.
B341371
1.292,1.781 1.292,1.604 false 2.229,1.208 2.229,1.031 false 2.094,1.25 2.552,1.448 0.458,0.198 10 SST 1.156,1.813 1.615,2.01 0.458,0.198 10 SST

Connect 2 SST, and then connect them to the front seat outer belt selectable force limiter.

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the selectable force limiter connector.


2.
C154370
0.688,0.875 1.094,0.875 false 1.615,1.813 1.917,2.063 0.302,0.25 10 *a 0.385,0.802 0.844,1 0.458,0.198 10 SST
*a 10 m or more


Move SST at least 10 m (33 ft.) away from the front of the vehicle.

3.

Close all the doors and windows of the vehicle.

NOTICE:

Do not damage the SST wire harness.




v.

Deploy the front seat outer belt selectable force limiter.

1.

Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.

2.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.

3.

Press the SST deployment switch to deploy the front seat outer belt selectable force limiter.

HINT:

The seat belt selectable force limiter will deploy at the same time as the LED of SST illuminates.





f.
B334893

Dispose of the front seat outer belt assembly.

i.

Remove the front seat outer belt assembly and SST.


ii.

Place the front seat outer belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

CAUTION:
·

The front seat outer belt becomes very hot when the front seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.

·

Use gloves and safety glasses when handling a front seat outer belt with a pretensioner that has been deployed.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt assembly with a pretensioner that has been deployed.



HINT:

When scrapping a vehicle, deploy the front seat outer belt pretensioners, and then scrap the vehicle with the deployed outer belt installed.




Hide 73220 2.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When not Installed in Vehicle)

CAUTION:
·

Use gloves and safety glasses when handling a front seat outer belt with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt with a deployed pretensioner.

·

When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.



NOTICE:
·

When disposing of a front seat outer belt with a pretensioner, never deploy the pretensioner in the customer's vehicle.

·

Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.

·

The seat belt pretensioner produces an exploding sound when it deploys, so perform the operation outdoors where it will not disturb local residents.

·

When deploying a front seat outer belt (with a seat belt pretensioner), perform the operation at least 10 m (33 ft.) away from the front seat outer belt.

·

Be sure to follow the procedure listed below when deploying the seat belt pretensioner.



a.
B050515
0.719,0.906 0.948,1.208 false 0.406,0.823 0.865,1.021 0.458,0.198 10 SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the seat belt pretensioner, always use the specified SST.


i.
B050511
0.865,1.135 1.177,1.5 false 2.563,0.833 2.281,0.833 false 0.5,1.021 0.885,1.219 0.385,0.198 10 SST 2.615,0.729 2.885,0.979 0.271,0.25 10 *1
*1 Battery


Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

HINT:

At this time, do not connect the yellow connector. It will in a later step be connected to the seat belt pretensioner.



ii.
B050514
2.156,1.021 2.573,1.021 false 2.635,0.927 3,1.167 0.365,0.24 10 SST

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.




b.

Remove the front seat outer belt assembly.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL


c.
B334894
2.031,0.302 2.344,0.5 0.313,0.198 10 *a 0.948,0.74 1.26,0.938 0.313,0.198 10 *b
*a Cut
*b 100 mm


Wind the seat belt webbing with the retractor.


d.

When the seat belt webbing is sufficiently wound, cut the seat belt webbing approximately 100 mm (3.94 in.) from the retractor as shown in the illustration.

HINT:

The retractor resistance increases in correlation with how much the seat belt webbing is wound.



e.

for Driver Side, Front Passenger Seat Belt without Selectable Force Limiter:

i.

Connect SST.

SST
09082-00700  
09082-00770  

1.
B334892
2.083,1.219 2.083,0.969 false 1.333,1.802 1.333,1.552 false 1.958,1.25 2.417,1.448 0.458,0.198 10 SST 1.208,1.833 1.667,2.031 0.458,0.198 10 SST

Connect 2 SST, and then connect them to the front seat outer belt pretensioner.

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.


2.
B334896
2.708,1.198 2.708,0.948 false 0.552,1.75 0.885,1.75 false 2.573,1.219 3.031,1.417 0.458,0.198 10 SST 0.26,1.677 0.719,1.875 0.458,0.198 10 SST

Place the front seat outer belt on the ground and cover it with a tire and wheel assembly.

NOTICE:
·

Position the front seat outer belt assembly as shown in the illustration.

·

Use a scrap tire and wheel assembly when disposing of a seat belt pretensioner.



3.

Position and hold SST at least 10 m (33 ft.) away from the wheel.

NOTICE:

Do not damage the SST wire harness.




ii.

Deploy the front seat outer belt pretensioner.

1.
B339081
1.927,0.917 2.198,1.156 false 1.625,1.823 1.938,2.021 0.313,0.198 10 *a 1.635,0.823 2,1 0.365,0.177 10 SST
*a 10 m or more


Check that no one is within a 10 m (33 ft.) radius of the wheel.

2.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

3.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.





f.

for Front Passenger Seat Belt with Selectable Force Limiter:

i.

Connect SST.

SST
09082-00700  
09082-00770  

1.
B341367
1.292,1.771 1.292,1.51 false 2.083,1.208 2.083,0.948 false 1.177,1.844 1.635,2.042 0.458,0.198 10 SST 1.958,1.24 2.417,1.438 0.458,0.198 10 SST

Connect 2 SST, and then connect them to the front seat outer belt pretensioner.

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.


2.
B341368
0.698,1.719 0.958,1.719 false 2.729,1.115 2.729,0.958 false 0.354,1.625 0.813,1.823 0.458,0.198 10 SST 2.615,1.167 3.073,1.365 0.458,0.198 10 SST

Place the front seat outer belt on the ground and cover it with a tire and wheel assembly.

NOTICE:
·

Position the front seat outer belt assembly as shown in the illustration.

·

Use a scrap tire and wheel assembly when disposing of a seat belt pretensioner.



3.

Position and hold SST at least 10 m (33 ft.) away from the wheel.

NOTICE:

Do not damage the SST wire harness.




ii.

Deploy the front seat outer belt pretensioner.

1.
B339081
1.927,0.917 2.198,1.156 false 1.625,1.823 1.938,2.021 0.313,0.198 10 *a 1.635,0.823 2,1 0.365,0.177 10 SST
*a 10 m or more


Check that no one is within a 10 m (33 ft.) radius of the wheel.

2.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

3.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.




iii.

Disconnect the SST.

CAUTION:

The front seat outer belt becomes very hot when the front seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.



iv.

Connect SST.

SST
09082-00700  
09082-00770  

1.
B341371
1.292,1.781 1.292,1.604 false 2.229,1.208 2.229,1.031 false 2.094,1.25 2.552,1.448 0.458,0.198 10 SST 1.156,1.813 1.615,2.01 0.458,0.198 10 SST

Connect 2 SST, and then connect them to the front seat outer belt selectable force limiter.

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the selectable force limiter connector.


2.
B341372
2.729,1.167 2.729,0.958 false 0.75,1.719 0.958,1.719 false 0.417,1.646 0.875,1.844 0.458,0.198 10 SST 2.594,1.26 3.052,1.458 0.458,0.198 10 SST

Place the front seat outer belt on the ground and cover it with a tire and wheel assembly.

NOTICE:
·

Position the front seat outer belt assembly as shown in the illustration.

·

Use a scrap tire and wheel assembly when disposing of a seat belt pretensioner.



3.

Position and hold SST at least 10 m (33 ft.) away from the wheel.

NOTICE:

Do not damage the SST wire harness.




v.

Deploy the front seat outer belt selectable force limiter.

1.
B339081
1.927,0.917 2.198,1.156 false 1.625,1.823 1.938,2.021 0.313,0.198 10 *a 1.635,0.823 2,1 0.365,0.177 10 SST
*a 10 m or more


Check that no one is within a 10 m (33 ft.) radius of the wheel.

2.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

3.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt selectable force limiter will deploy at the same time as the LED of SST illuminates.





g.
B334893

Dispose of the front seat outer belt assembly.

i.

Remove the wheel and SST.


ii.

Place the front seat outer belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

CAUTION:
·

The front seat outer belt becomes very hot when the front seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.

·

Use gloves and safety glasses when handling a front seat outer belt with a pretensioner that has been deployed.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt assembly with a pretensioner that has been deployed.



HINT:

When scrapping a vehicle, deploy the front seat outer belt pretensioners, and then scrap the vehicle with the deployed outer belt installed.