Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › 2012.12–2016.08
RM3090E _58 Vehicle Interior _008788 SEAT BELT _0050327 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 73200A 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B334890C01
0.844,0.406 1.677,0.406 true 0.823,1.927 1.74,1.927 true 0.615,1.844 0.927,2.042 0.313,0.198 10 *1 0.667,0.333 0.979,0.531 0.313,0.198 10 *2
*1 Bolt (A)
*2 Bolt (B)


Attach the guide to temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.


b.

Tighten the bolt (A).

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Tighten the bolt (B).

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73220 2.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B334888

Align the 2 claws with the seat belt positioning holes, and install the retractor of the front seat outer belt assembly LH with the bolt as shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.
B334889

Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.



c.

Connect the shoulder anchor of the front seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73210 3.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (for Front Passenger Seat Belt with Selectable Force Limiter)

a.
B339094

Align the 2 claws with the seat belt positioning holes, and install the retractor of the front seat outer belt assembly RH with the bolt as shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.
B339095

Connect the pretensioner connector and selectable force limiter connector, and lock the 2 locking buttons as shown in the illustration.

NOTICE:

Securely lock the locking button.



c.

Connect the shoulder anchor of the front seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62412 4.INSTALL CENTER PILLAR GARNISH LH

Hide 62414A 5.INSTALL LOWER CENTER PILLAR GARNISH LH

Hide 6.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

a.

Connect the floor anchor of the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Check that the front seat outer belt assembly LH is not twisted.


Hide 73233 7.INSTALL OUTER LAP BELT ANCHOR COVER

a.

Attach the 3 claws to install the outer lap belt anchor cover.


Hide 62332C 8.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67918E 9.INSTALL REAR DOOR SCUFF PLATE LH

Hide 62312B 10.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67914B 11.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION