Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › 2012.12–2015.10
RM3090E _59 Vehicle Exterior _008794 DOOR / HATCH _0050374 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B2226  PBD Unit Pulse Sensor LH Circuit  


DESCRIPTION

This DTC is output when the multiplex network door ECU detects a power back door unit assembly set LH pulse malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2226 PBD Unit Pulse Sensor LH Circuit This DTC is output when the multiplex network door ECU detects a power back door unit assembly set LH pulse malfunction.
·

Multiplex network door ECU

·

Power back door unit assembly set LH

·

Harness or connector



WIRING DIAGRAM

B341467E01
1.083,2.667 1.542,2.865 0.458,0.198 10 U18 1.104,2.833 5.083,3.031 3.979,0.198 10 Multiplex Network Door ECU 4.458,2.667 4.917,2.865 0.458,0.198 10 U21 4.5,2.885 5.917,3.25 1.417,0.365 10 Power Back Door Unit Assembly Set LH 2.292,2.167 2.75,2.365 0.458,0.198 10 DS1 2.292,1.667 2.75,1.865 0.458,0.198 10 DSV 2.292,1.167 2.75,1.365 0.458,0.198 10 DSG 4.583,1.135 5.042,1.333 0.458,0.198 10 DSG 2.292,0.635 2.75,0.833 0.458,0.198 10 DS2 4.583,0.635 5.042,0.833 0.458,0.198 10 DS2 4.583,1.667 5.042,1.865 0.458,0.198 10 DSV 4.583,2.167 5.042,2.365 0.458,0.198 10 DS1 2.667,0.5 3.125,0.698 0.458,0.198 10 22 2.667,1 3.125,1.198 0.458,0.198 10 11 2.667,1.552 3.125,1.75 0.458,0.198 10 12 2.667,2.083 3.125,2.281 0.458,0.198 10 23 4.333,0.5 4.792,0.698 0.458,0.198 10 6 4.333,1 4.792,1.198 0.458,0.198 10 4 4.333,1.552 4.792,1.75 0.458,0.198 10 3 4.333,2.083 4.792,2.281 0.458,0.198 10 5

PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Clear DTCs
50002 159

b.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Proceed to
DTC B2226 is not output
DTC B2226 is output



DTC B2226 is not output

DTC B2226 is output

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)
a.

Disconnect the U18 multiplex network door ECU connector.


b.

Disconnect the U21 power back door unit assembly set LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U18-11 (DSG) - U21-4 (DSG) Always Below 1 Ω
U18-12 (DSV) - U21-3 (DSV) Always Below 1 Ω
U18-22 (DS2) - U21-6 (DS2) Always Below 1 Ω
U18-23 (DS1) - U21-5 (DS1) Always Below 1 Ω
U18-11 (DSG) or U21-4 (DSG) - Body ground Always 10 kΩ or higher
U18-12 (DSV) or U21-3 (DSV) - Body ground Always 10 kΩ or higher
U18-22 (DS2) or U21-6 (DS2) - Body ground Always 10 kΩ or higher
U18-23 (DS1) or U21-5 (DS1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE POWER BACK DOOR UNIT ASSEMBLY SET LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE POWER BACK DOOR UNIT ASSEMBLY SET LH
a.

Temporarily replace the power back door unit assembly set LH with a new or normally functioning one.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR DRIVE UNIT>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Clear DTCs
50002 159

b.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Proceed to
DTC B2226 is not output
DTC B2226 is output



DTC B2226 is not output

END (POWER BACK DOOR UNIT ASSEMBLY SET LH WAS DEFECTIVE)

DTC B2226 is output

REPLACE MULTIPLEX NETWORK DOOR ECU