Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor)
RM3090E _59 Vehicle Exterior _008795 WIPER / WASHER _0050248 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  Rain Sensor Circuit  


DESCRIPTION

The windshield wiper relay assembly receives a signal from the rain sensor to control the auto wiper system.

WIRING DIAGRAM

E270595E01
3.094,2.656 4.781,2.854 1.688,0.198 10 false Q5*1, Q10*2 3.104,2.833 4.792,3.031 1.688,0.198 10 false Rain Sensor 0.938,3.26 4.604,3.458 3.667,0.198 10 false : LIN Communication Line 5.396,2.625 5.854,2.823 0.458,0.198 10 false G85 5.406,2.802 6.51,3.219 1.104,0.417 10 false Windshield Wiper Relay Assembly 0.219,0.875 1.125,1.281 0.906,0.406 10 false from IG1 NO.1 Relay 1.844,1.021 3.677,1.219 1.833,0.198 10 false ECU-IG NO.2 3.563,1.458 4.021,1.656 0.458,0.198 10 false MPX 5.302,1.271 5.615,1.469 0.313,0.198 10 false 14 3.948,1.281 4.26,1.479 0.313,0.198 10 false 1 2.917,1.917 3.375,2.115 0.458,0.198 10 false 2 2.865,0.75 3.323,0.948 0.458,0.198 10 false 4 5.573,1.448 6.188,1.646 0.615,0.198 10 false MPX1 3.135,0.865 3.594,1.063 0.458,0.198 10 false SIG 0.188,2.563 1.875,2.76 1.688,0.198 10 false *1: for LHD 0.198,2.917 1.885,3.115 1.688,0.198 10 false *2: for RHD 3.156,2.031 3.615,2.229 0.458,0.198 10 false ES

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - RAIN SENSOR)
a.

Disconnect the G85 windshield wiper relay assembly connector.


b.

Disconnect the Q5*1 or Q10*2 rain sensor connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G85-14 (MPX1) - Q5-1 (MPX) Always Below 1 Ω
G85-14 (MPX1) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G85-14 (MPX1) - Q10-1 (MPX) Always Below 1 Ω
G85-14 (MPX1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (RAIN SENSOR - BATTERY AND BODY GROUND)
a.
E270596C01
0.219,0.75 0.552,0.99 0.333,0.24 0.25,1.146 0.583,1.385 0.333,0.24 1.25,1.75 1.5,1.75 1.5,1.75 1.615,1.375 true 2.417,1.75 2.167,1.75 2.167,1.75 2.031,1.375 true 1.021,1.667 1.333,1.865 0.313,0.198 10 ES 2.458,1.667 2.917,1.865 0.458,0.198 10 SIG 0.115,0.104 0.427,0.302 0.313,0.198 10 *a 0.271,0.792 0.729,0.99 0.458,0.198 10 Q5 0.281,1.198 0.74,1.396 0.458,0.198 10 Q10 0.615,0.781 0.927,0.979 0.313,0.198 10 *A 0.646,1.167 0.958,1.365 0.313,0.198 10 *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Rain Sensor)


Disconnect the rain sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
Q5-2 (ES) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
O10-2 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
Q5-4 (SIG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
Q10-4 (SIG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK RAIN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RAIN SENSOR
a.
E257042C03
0.313,0.833 0.656,1.073 0.344,0.24 0.302,1.385 0.646,1.625 0.344,0.24 1.969,0.958 2.115,0.302 2.115,0.302 2.354,0.302 true 1.802,0.958 1.583,0.292 1.583,0.292 1.375,0.292 true 0.156,0.177 0.469,0.375 0.313,0.198 10 *a 1.125,0.229 1.438,0.427 0.313,0.198 10 ES 2.417,0.229 2.854,0.438 0.438,0.208 10 MPX 0.396,0.865 0.708,1.063 0.313,0.198 10 Q5 0.344,1.438 0.802,1.635 0.458,0.198 10 Q10 0.719,0.854 1.031,1.052 0.313,0.198 10 *A 0.729,1.417 1.042,1.615 0.313,0.198 10 *B
*A for LHD
*B for RHD
*a Component with harness connected
(Rain Sensor)


Remove the rain sensor with the connector(s) still connected.


b.

Connect an oscilloscope to terminals 1 (MPX) and 2 (ES) of the rain sensor connector.


c.

Check the waveform of the rain sensor using the oscilloscope.

OK:
for LHD
Tester Connection Switch Condition Specified Condition
O5-1 (MPX) - O5-2 (ES) Ignition switch ON Pulse generation

for RHD
Tester Connection Switch Condition Specified Condition
O10-1 (MPX) - O10-2 (ES) Ignition switch ON Pulse generation


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG