Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type) › 2012.12–2015.04
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047060 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The clearance warning ECU assembly receives a reverse shift position signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: except Manual Transaxle

*2: for Manual Transaxle


WIRING DIAGRAM

E270560E01
0.094,0.073 2.375,0.281 2.281,0.208 12 false except Manual Transaxle: 5.292,2.083 6.479,2.469 1.188,0.385 10 false Clearance Warning ECU Assembly 5.281,1.896 5.74,2.094 0.458,0.198 10 false G33 5.417,1.083 5.729,1.281 0.313,0.198 10 false RL 5.177,0.969 5.49,1.167 0.313,0.198 10 false 21 3.156,1.625 3.615,1.823 0.458,0.198 10 false B36 3.167,1.844 4.552,2.219 1.385,0.375 10 false Park/Neutral Position Switch Assembly 2.073,1.313 2.844,1.51 0.771,0.198 10 false GAUGE 4.396,0.979 4.552,1.177 0.156,0.198 10 false 2 3.26,0.99 3.417,1.188 0.156,0.198 10 false 1 0.396,1.073 1.396,1.292 1,0.219 10 false IG1 NO.2 Relay

E270560E02
0.094,0.073 1.906,0.323 1.813,0.25 12 for Manual Transaxle: 5.292,2.083 6.479,2.469 1.188,0.385 10 Clearance Warning ECU Assembly 5.281,1.896 5.74,2.094 0.458,0.198 10 G33 5.417,1.083 5.729,1.281 0.313,0.198 10 RL 5.177,0.969 5.49,1.167 0.313,0.198 10 21 3.229,1.646 3.688,1.844 0.458,0.198 10 B35 3.24,1.844 4.563,2.219 1.323,0.375 10 Back-up Light Switch Assembly 2.073,1.313 2.844,1.51 0.771,0.198 10 GAUGE 4.396,0.979 4.552,1.177 0.156,0.198 10 1 3.26,0.99 3.417,1.188 0.156,0.198 10 2 0.396,1.073 1.396,1.292 1,0.219 10 IG1 NO.2 Relay

PROCEDURE

1.CHECK CLEARANCE WARNING ECU ASSEMBLY (REVERSE SIGNAL)
a.

Disconnect the G33 clearance warning ECU assembly connector.


b.
E270561C02
1.49,0.208 1.906,0.479 0.417,0.271 1.74,1.771 2.104,1.177 false 0.104,0.063 0.417,0.26 0.313,0.198 10 *a 1.563,0.26 1.906,0.448 0.344,0.188 10 G33 1.521,1.698 1.833,1.896 0.313,0.198 10 RL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G33-21 (RL) - Body ground Ignition switch ON
Shift lever in R
11 to 14 V
G33-21 (RL) - Body ground Ignition switch ON
Shift lever in any position except R
Below 1 V



Result:
Result
OK
NG (except Manual Transaxle)
NG (for Manual Transaxle)



OK

NG (except Manual Transaxle)

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG (for Manual Transaxle)

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G33 clearance warning ECU assembly connector.


b.

Disconnect the B36 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-21 (RL) - B36-2 Always Below 1 Ω
G33-21 (RL) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for U660F) A
OK (for U760E) B
OK (for U760F) C
NG D



A

B

C

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G33 clearance warning ECU assembly connector.


b.

Disconnect the B35 back-up light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-21 (RL) - B35-1 Always Below 1 Ω
G33-21 (RL) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for EA64) A
OK (for EA64F) B
OK (for EB61) C
OK (for EB61F) D
NG E



A

B

C

D

E

REPAIR OR REPLACE HARNESS OR CONNECTOR