Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 4 Sensor Type)
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047060 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Indicator Circuit  


DESCRIPTION

The warning indicator lights are installed in the telltale light assembly.

WIRING DIAGRAM

E270589E01
5.5,2.719 6.688,3.073 1.188,0.354 10 Clearance Warning ECU Assembly 5.5,2.552 5.958,2.75 0.458,0.198 10 G33 5.615,0.802 5.927,1 0.313,0.198 10 L3 5.604,1.229 5.917,1.427 0.313,0.198 10 L2 5.615,1.656 5.927,1.854 0.313,0.198 10 L1 5.604,2.073 5.917,2.271 0.313,0.198 10 L10 5.333,0.729 5.646,0.927 0.313,0.198 10 23 5.385,1.146 5.542,1.344 0.156,0.198 10 8 5.396,1.573 5.552,1.771 0.156,0.198 10 7 5.354,1.969 5.667,2.167 0.313,0.198 10 10 4.375,0.698 4.531,0.896 0.156,0.198 10 3 4.375,1.146 4.531,1.344 0.156,0.198 10 2 4.375,1.563 4.531,1.76 0.156,0.198 10 4 4.375,1.979 4.531,2.177 0.156,0.198 10 5 4.063,0.823 4.375,1.021 0.313,0.198 10 BK 4.083,1.24 4.396,1.438 0.313,0.198 10 RL 4.063,1.667 4.375,1.865 0.313,0.198 10 RR 4.052,2.083 4.365,2.281 0.313,0.198 10 OP 3.198,1.458 3.813,1.656 0.615,0.198 10 LAPB 1.917,1.667 2.875,1.896 0.958,0.229 10 ECU-IG NO. 1 0.219,1.448 1.646,1.698 1.427,0.25 10 from IG1 NO. 1 Relay 3.01,2.563 3.469,2.76 0.458,0.198 10 G43 3,2.76 4.552,2.99 1.552,0.229 10 Telltale Light Assembly 2.969,1.333 3.125,1.531 0.156,0.198 10 9

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - BATTERY)
a.
E270586C02
1.5,0.302 1.938,0.573 0.438,0.271 2.083,1.25 2.719,0.531 false 0.094,0.083 0.406,0.281 0.313,0.198 10 *a 1.583,0.354 1.958,0.552 0.375,0.198 10 G43 2.813,0.438 3.333,0.615 0.521,0.177 10 LAPB
*a Front view of wire harness connector
(to Telltale Light Assembly)


Disconnect the telltale light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G43-9 (LAPB) - Body ground Ignition switch ON 11 to 14 V
G43-9 (LAPB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - TELLTALE LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - TELLTALE LIGHT ASSEMBLY)
a.

Disconnect the G33 clearance warning ECU assembly connector.


b.

Disconnect the G43 telltale light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-7 (L1) - G43-4 (RR) Always Below 1 Ω
G33-8 (L2) - G43-2 (RL) Always Below 1 Ω
G33-10 (L10) - G43-5 (OP) Always Below 1 Ω
G33-23 (L3) - G43-3 (BK) Always Below 1 Ω
G33-7 (L1) - Body ground Always 10 kΩ or higher
G33-8 (L2) - Body ground Always 10 kΩ or higher
G33-10 (L10) - Body ground Always 10 kΩ or higher
G33-23 (L3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TELLTALE LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TELLTALE LIGHT ASSEMBLY


Result:
Proceed to
OK
NG



OK

NG