33111A
1.REMOVE MANUAL TRANSMISSION FILLER PLUG
Remove the manual transmission filler plug and gasket from the manual transmission case.
33111A
2.REMOVE MANUAL TRANSMISSION DRAIN PLUG
Remove the manual transmission drain plug and gasket from the front transaxle case.
84210
3.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY
Using a 27 mm deep socket wrench, remove the back-up light switch assembly and gasket from the manual transmission case.
33111C
4.REMOVE TRANSMISSION CASE PLUG
Remove the transmission case plug and gasket from the manual transmission case.
335A0
5.REMOVE CONTROL CABLE BRACKET ASSEMBLY
Remove the 3 bolts and control cable bracket assembly from the manual transmission case.
31478
6.REMOVE RELEASE CYLINDER BLEEDER PLUG CAP
Remove the release cylinder bleeder plug cap from the release cylinder bleeder plug.
31477
7.REMOVE RELEASE CYLINDER BLEEDER PLUG
Remove the release cylinder bleeder plug from the clutch release bleeder sub-assembly.
31407B
8.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY
31400
9.REMOVE CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY
30300
10.SECURE MANUAL TRANSAXLE ASSEMBLY
Place the manual transaxle assembly on wooden blocks.
33451H
11.REMOVE REVERSE IDLER GEAR SHAFT BOLT
Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.
33292A
12.REMOVE LOCK BALL PIN
Using a 10 mm hexagon socket wrench, remove the shift and select lever shaft straight screw with head plug from the manual transmission case.
Using a magnet hand, remove the shift and select lever shaft compression spring and lock ball pin from the manual transmission case.
Using a 10 mm hexagon socket wrench, remove the shift and select lever shaft straight screw with head plug from the manual transmission case.
Using a magnet hand, remove the shift and select lever shaft compression spring and lock ball pin from the manual transmission case.
33275C
13.REMOVE SHIFT DETENT BALL
Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the manual transmission case.
Using a magnet hand, remove the shift detent ball compression spring and shift detent ball from the manual transmission case.
Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the manual transmission case.
Using a magnet hand, remove the 2 shift detent ball compression springs and 2 shift detent balls from the manual transmission case.
33253F
14.REMOVE OUTER SHIFT LEVER E-RING
Remove the outer shift lever E-ring from the outer No. 1 shift lever.
15.REMOVE MANUAL TRANSMISSION CASE
Remove the 17 bolts.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, separate the manual transmission case from the front transaxle case.
Do not damage the manual transmission case.
Turn the outer No. 1 shift lever clockwise until it comes into contact with the boss.
Push the outer No. 1 shift lever and remove the manual transmission case.
33402
16.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY
Remove the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft from the front transaxle case.
33211
17.REMOVE REVERSE SHIFT FORK ASSEMBLY
Turn the reverse shift fork shaft assembly clockwise and remove it from the front transaxle case.
33211
18.REMOVE REVERSE SHIFT FORK
Using a 5 mm pin punch and hammer, tap out the reverse shift fork slotted spring pin.
Remove the reverse shift fork from the reverse shift fork shaft assembly.
33240
19.REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY
Using a 6 mm hexagon socket wrench, remove the 2 bolts and reverse shift arm bracket assembly from the front transaxle case.
20.REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY
Turn the shift and select lever shaft assembly clockwise and remove it from the front transaxle case.
33257
21.REMOVE OUTER SELECT LEVER
Remove the inner select lever bolt.
Remove the outer select lever and inner select lever from the front transaxle case.
33257C
22.REMOVE OUTER SELECT LEVER OIL SEAL
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, remove the outer select lever oil seal from the front transaxle case.
Do not damage the installation surfaces.
23.REMOVE INPUT SHAFT ASSEMBLY
Remove the input shaft assembly, output shaft assembly and 2 gear shift fork shaft assemblies from the front transaxle case.
Remove the output shaft assembly together with the No. 1 gear shift fork shaft assembly from the input shaft assembly.
Remove the No. 1 gear shift fork shaft assembly from the output shaft assembly.
Remove the No. 2 gear shift fork shaft assembly from the input shaft assembly.
24.REMOVE DIFFERENTIAL CASE ASSEMBLY
Remove the differential case assembly from the front transaxle case.
33449B
25.REMOVE TRANSMISSION MAGNET
Remove the transmission magnet from the front transaxle case.
33101J
26.REMOVE BREATHER PLUG
Remove the breather plug from the front transaxle case.
33321N
27.REMOVE FRONT OUTPUT SHAFT BEARING
Using SST, tap the front output shaft bearing (outer race) from the front transaxle case.
Remove the output shaft cover from the front transaxle case.
31105D
28.REMOVE FRONT TRANSAXLE CASE OIL SEAL
Using SST, tap out the front transaxle case oil seal from the front transaxle case.
29.REMOVE STRAIGHT PIN
Remove the 5 straight pins from the front transaxle case.
33311K
30.REMOVE REAR INPUT SHAFT BEARING SHIM
Remove the rear input shaft bearing shim from the manual transmission case.
33137
31.REMOVE INPUT SHAFT COVER
Remove the input shaft cover from the manual transmission case.
32.REMOVE OIL RECEIVER PIPE
Remove the No. 1 oil receiver pipe from the manual transmission case.
33253
33.REMOVE OUTER NO. 1 SHIFT LEVER
Using a 5 mm pin punch and hammer, tap out the inner shift lever slotted spring pin.
When removing the inner shaft lever slotted spring pin, align the inner shift lever slotted spring pin with the hole in the lock ball assembly.
Remove the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever from the manual transmission case.
33253H
34.REMOVE OUTER SHIFT LEVER OIL SEAL
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, remove the outer shift lever oil seal from the manual transmission case.
Do not damage the installation surfaces.
33321A
35.REMOVE REAR OUTPUT SHAFT BEARING
Using SST, remove the rear output shaft bearing (outer race) and rear output shaft bearing shim from the manual transmission case.
33111Q
36.REMOVE TRANSMISSION CASE OIL SEAL (for LH Side)
Using SST, remove the transmission case oil seal from the manual transmission case.
31105H
37.REMOVE TRANSAXLE CASE OIL SEAL (for RH Side)
Using SST, remove the transmission case oil seal from the front transaxle case.
41311E
38.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
Using SST, remove the front differential case front tapered roller bearing (outer race) and front differential oil baffle from the front transaxle case.
| *a | Turn |
| *b | Hold |
Using SST, remove the front differential case front tapered roller bearing from the differential case assembly.
41311F
39.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
Using SST, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear shim from the manual transmission case.
| *a | Turn |
| *b | Hold |
Using SST, remove the front differential case rear tapered roller bearing from the differential case assembly.