When the ignition switch is ON, the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is operated by the power window regulator master switch assembly. The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has motor and ECU functions.
Inspect the fuses for circuits related to this system before performing the following procedure.
The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been replaced with a new one, initialize the power window control system.
When the ECU determines that the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has a malfunction, DTC B2311 is stored.
Clear the DTC.
Check for DTCs.
| Proceed to |
|---|
| DTC is not output |
| DTC is output |
DTC is not output
DTC is output
Perform the Active Test according to the display on the GTS.
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Driver door power window | OFF, UP or DOWN | - |
Up and down movement does not occur if the arrow is not pressed and held.
| Tester Display |
|---|
| Power Window |
Driver door power window operates normally.
| Proceed to |
|---|
| OK |
| NG (for LHD) |
| NG (for RHD) |
OK
NG (for LHD)
NG (for RHD)
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Door P/W Up SW | Driver door power window manual up switch signal | ON or OFF | ON: Driver door power window manual up switch being operated
OFF: Driver door power window manual up switch not being operated |
- |
| D Door P/W Down SW | Driver door power window manual down switch signal | ON or OFF | ON: Driver door power window manual down switch being operated
OFF: Driver door power window manual down switch not being operated |
- |
| Tester Display |
|---|
| D Door P/W Up SW |
| D Door P/W Down SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK (for LHD) |
| OK (for RHD) |
| NG |
OK (for LHD)
OK (for RHD)
NG
| *a | Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly LH) |
Disconnect the front power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J3-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J3-2 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power window regulator master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL
Inspect the power window regulator master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly) |
Disconnect the power window regulator master switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J5-1 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I5-9 (E) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J5-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I5-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK (for LHD) |
| OK (for RHD) |
| NG |
OK (for LHD)
OK (for RHD)
NG
Disconnect the J5 power window regulator master switch assembly connector.
Disconnect the J3 front power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J5-8 (U) - J3-10 (UP) | Always | Below 1 Ω |
| J5-5 (D) - J3-7 (DOWN) | Always | Below 1 Ω |
| J5-8 (U) or J3-10 (UP) - Body ground | Always | 10 kΩ or higher |
| J5-5 (D) or J3-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Power Window Regulator Motor Assembly RH) |
Disconnect the front power window regulator motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I3-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I3-2 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I5 power window regulator master switch assembly connector.
Disconnect the I3 front power window regulator motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I5-1 (U) - I3-10 (UP) | Always | Below 1 Ω |
| I5-5 (D) - I3-7 (DOWN) | Always | Below 1 Ω |
| I5-1 (U) or I3-10 (UP) - Body ground | Always | 10 kΩ or higher |
| I5-5 (D) or I3-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG