Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0711  Transmission Fluid Temperature Sensor "A" Performance  


DESCRIPTION

The CVT fluid temperature sensor converts the fluid temperature into a resistance value which is detected by the ECM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies a voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.

HINT:

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0711 Transmission Fluid Temperature Sensor "A" Performance 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The intake air and engine coolant temperatures are more than -10°C (14°F) at engine start, and the vehicle is driven for over 18 minutes and 7 km/h (4.3 miles) or more.

2.

CVT fluid temperature is less than 20°C (68°F).

3.

3 seconds

4.

2 trip detection logic


1.

The engine coolant temperature is less than 35°C (95°F) at engine start.

2.

The CVT fluid temperature is 100°C (212°F) or higher.

3.

10 seconds

4.

2 trip detection logic


·

CVT fluid level

·

Continuously variable transaxle assembly


Comes on DTC stored

MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and detects open or short circuits in the CVT fluid temperature circuit.

After driving the vehicle for a certain period, the CVT fluid temperature should increase. When the CVT fluid temperature is below 20°C (68°F), the ECM interprets this as a fault and turns on the MIL.

When the engine coolant temperature reaches 35°C (95°F) after a cold engine start, if the CVT fluid temperature is 100°C (212°F) or higher, the ECM also determines this as a fault, turns on the MIL, and stores the DTC.

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0711)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

Result:
Proceed to
Only P0711 is output
P0711 and other DTCs are output


HINT:

If any other DTCs besides P0711 are output, perform troubleshooting for those DTCs first.




Only P0711 is output

2.CHECK TRANSAXLE FLUID LEVEL

P0711 and other DTCs are output

2.CHECK TRANSAXLE FLUID LEVEL
a.

Check the CVT fluid level.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE FLUID>ADJUSTMENT

OK:

CVT fluid level is correct.



Result:
Proceed to
OK
NG



OK

3.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NG

3.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT