Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › 2012.12–2015.10
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051014 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 16282 2.DISCONNECT WATER BY-PASS HOSE

C279758

a.

Slide the 2 clips and disconnect the 2 water by-pass hoses from the oil cooler.


Hide 12325A 4.REMOVE ENGINE MOUNTING BRACKET LH

C279759

a.

Remove the 3 bolts and engine mounting bracket LH from the continuously variable transaxle assembly.


Hide 12311A 5.REMOVE FRONT ENGINE MOUNTING BRACKET

C279760

a.

Remove the 3 bolts and front engine mounting bracket from the continuously variable transaxle assembly.


Hide 12321A 6.REMOVE REAR ENGINE MOUNTING BRACKET

C203362

a.

Remove the 3 bolts and rear engine mounting bracket from the continuously variable transaxle assembly.


Hide 7.REMOVE GROUND CABLE

C203354

a.

Detach the clamp.


b.

Remove the bolt and ground cable.


Hide 82121 8.DISCONNECT ENGINE WIRE

a.

for Front Side:

Disconnect the transmission wire connector, park/neutral position switch connector and 3 revolution sensor connectors, and detach the 3 wire harness clamps from the continuously variable transaxle assembly.


b.

for Rear Side:

Disconnect the oil pressure sensor connector and detach the 2 wire harness clamps from the continuously variable transaxle assembly.

C279761C01
0.302,0.115 0.667,0.406 0.365,0.292 10 *a 3.802,0.115 4.208,0.406 0.406,0.292 10 *b
*a for Front Side *b for Rear Side



Hide 32101A 9.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

C279068

a.

Remove the flywheel housing under cover.


b.

Turn the crankshaft to gain access to the location of the 6 drive plate and torque converter assembly setting bolts and each bolt while holding the crankshaft pulley bolt with a wrench.


Hide 30400 10.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

C203356

a.

Remove the 8 bolts and continuously variable transaxle assembly from the engine assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.



Hide 36100 11.REMOVE TRANSFER ASSEMBLY

Hide 36100A 12.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT


a.
C291117

Remove the 2 transfer and transaxle setting stud bolts.

HINT:

It is not necessary to remove the transfer and transaxle setting stud bolts unless they are being replaced.



Hide 33823 13.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C279762

a.

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 14.REMOVE WIRE HARNESS CLAMP BRACKET

a.

Remove the 4 bolts and 4 wire harness clamp brackets from the continuously variable transaxle assembly.

C279763


Hide 32000A 15.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the continuously variable transaxle assembly.


Hide 30400E 16.REMOVE CVT OIL PUMP TYPE T OIL SEAL

NOTICE:
·

Do not remove the front oil pump assembly from the CVT main body, as there is the possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from running, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, etc.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque convertor is not attached to it.

·

Do not use the air gun until the torque convertor has been installed, as it could cause dust and foreign matter to be stirred up.



a.
C208788E10
2.406,2.063 2.406,2.677 false 2.292,2.75 2.792,3 0.5,0.25 10 SST

Clean the tips of both the claws of SST and the center bolt.


b.

Using SST, remove the CVT oil pump type T oil seal.

SST
09308-10010  

NOTICE:
·

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.