Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2012.12–2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The CVT fluid temperature sensor converts the fluid temperature into a resistance value which is detected by the ECM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies a voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.

HINT:

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in heavy traffic.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

-

2.

There is a short circuit in the CVT fluid temperature sensor circuit.

3.

0.5 seconds

4.

1 trip detection logic


·

Short in CVT fluid temperature sensor circuit

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored
P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

15 minutes or more after starting the engine.

2.

There is an open circuit in the CVT fluid temperature sensor circuit.

3.

0.5 seconds

4.

1 trip detection logic


·

Open in CVT fluid temperature sensor circuit

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and detects open or short circuits in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature sensor is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the CVT fluid temperature sensor or wiring. The ECM turns on the MIL and stores the DTC.

*1: 150°C (302°F) or higher is indicated regardless of the actual CVT fluid temperature.

*2: -40°C (-40°F) is indicated regardless of the actual CVT fluid temperature.

HINT:

The CVT fluid temperature can be checked on the GTS display.


WIRING DIAGRAM

C251555E03
5.771,2.99 6.135,3.188 0.365,0.198 10 B75 5.771,3.188 6.219,3.375 0.448,0.188 10 ECM 0.385,2.75 0.781,2.948 0.396,0.198 10 B37 0.375,2.979 4.365,3.25 3.99,0.271 10 Transmission Wire (Continuously Variable Transaxle Assembly) 5.615,1.271 6.073,1.479 0.458,0.208 10 THO1 5.615,2.219 6.073,2.427 0.458,0.208 10 ETHO 5.323,1.365 5.594,1.573 0.271,0.208 10 95 5.313,2.344 5.573,2.542 0.26,0.198 10 96 3.927,1.365 4.135,1.563 0.208,0.198 10 1 3.927,2.344 4.135,2.542 0.208,0.198 10 6 3.51,1.104 3.927,1.313 0.417,0.208 10 THO 3.604,2.083 3.896,2.281 0.292,0.198 10 E2 1.521,1.719 3.49,1.958 1.969,0.24 10 CVT Fluid Temperature Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (A/T OIL TEMPERATURE 1)
a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 234 406
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 CVT fluid temperature sensor value min.: -40°C (-40°F)
max.: 215°C (419°F)
·

After stall speed test: Approx. 100°C (212°F)

·

Equal to ambient temperature after cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or higher, the CVT fluid temperature sensor circuit is open or shorted.

g.

In accordance with the display on the GTS, read the Data List.

Result:
Proceed to
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition




Data displayed is not as specified under Normal Condition

2.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)

Data displayed is as specified under Normal Condition

4.REPLACE ECM
2.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)
a.
C199169C01
2.094,0.948 2.49,0.469 true 2.479,1.781 2.104,1.25 true 2.573,0.375 3.01,0.615 0.438,0.24 10 THO 0.115,0.094 0.427,0.292 0.313,0.198 10 *a 2.573,1.708 2.979,1.938 0.406,0.229 10 E2
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (THO) - 6 (E2) Always 79 Ω to 156 kΩ
1 (THO) - Body ground Always 10 kΩ or higher
6 (E2) - Body ground Always 10 kΩ or higher


HINT:

If the resistance is outside the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may be affected.


Resistance (Reference):
CVT Fluid Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C267934C12
1.49,0.135 1.938,0.385 0.448,0.25 2.198,1.771 1.781,1.083 true 1.396,1.781 1.719,1.083 true 1.604,0.177 2.063,0.375 0.458,0.198 10 B75 1.042,1.854 1.76,2.104 0.719,0.25 10 95 (THO1) 1.948,1.854 2.667,2.104 0.719,0.25 10 96 (ETHO) 0.115,0.083 0.385,0.323 0.271,0.24 10 *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B75-95 (THO1) - B75-96 (ETHO) Always 79 Ω to 156 kΩ
B75-95 (THO1) - Body ground Always 10 kΩ or higher
B75-96 (ETHO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT