Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0741  Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL)  P2757  Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance (Shift Solenoid Valve DSU)  


DESCRIPTION

The ECM uses shift solenoid valves SL and DSU to perform lock-up control in response to the driving conditions.

NOTICE:

If any parts inside the torque converter assembly are damaged, DTC P0741/64 and P2757/64 could be output. In this case, make sure to replace both the torque converter assembly and the continuously variable transaxle assembly as broken pieces may have entered through the oil passages and some of them may be present in the continuously variable transaxle assembly.


HINT:

Shift solenoid valve DSU controls the lock-up clutch pressure in response to the input torque.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.2 mph) or more with the shift lever in D.

2.

The lock-up signal is on, but lock-up is off.

3.

-

4.

2 trip detection logic


·

Continuously variable transaxle assembly

·

Torque converter assembly


Comes on DTC stored
P2757 Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance (Shift Solenoid Valve DSU) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.2 mph) or more with the shift lever in D.

2.

The lock-up signal is on, but lock-up is off.

3.

-

4.

2 trip detection logic


1.

The engine is warmed up, and the vehicle is driven at a speed of 8 km/h (5.0 mph) or more with the shift lever in D.

2.

The lock-up signal is off, but lock-up is on.

3.

-

4.

2 trip detection logic


·

Continuously variable transaxle assembly

·

Torque converter assembly


Comes on DTC stored

MONITOR DESCRIPTION

When performing lock-up control (on/off) of the torque converter, the ECM compares the rotating speeds of the turbine (NT) and engine (NE) to detect mechanical malfunctions in the shift solenoid valves SL and DSU. When the rotating speeds are different than expected, the ECM detects the problem, illuminates the MIL and stores the DTC.

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0741 AND P2757)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

Result:
Proceed to
Only P0741 and/or P2757 is output
P0741 and/or P2757 and other DTCs are output


HINT:

If any other DTCs besides P0741 or P2757 are output, perform troubleshooting for those DTCs first.




Only P0741 and/or P2757 is output

2.CLEAR DTC

P0741 and/or P2757 and other DTCs are output

2.CLEAR DTC
a.

Clear the DTC.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

3.PERFORM DRIVE TEST
3.PERFORM DRIVE TEST
CAUTION:
C246168C01
2.198,1.677 2.51,1.156 true 3.031,1.688 2.615,0.979 true 2.042,0.146 2.208,0.302 0.167,0.156 10 *a 3.125,1.625 3.344,1.802 0.219,0.177 10 *b 1.99,1.615 2.219,1.813 0.229,0.198 10 *1
*1 Oil seal
*a Example of the damage
*b Damage


Strictly observe posted speed limits, traffic laws and road conditions when performing the road test.


NOTICE:
·

This test must be conducted after checking and confirming that the engine is operating normally.

·

Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

·

Perform the test with the A/C off and no electrical load.

·

Make sure to replace both the torque converter assembly and the continuously variable transaxle assembly if any parts inside the torque converter assembly are damaged. Broken pieces may have entered through the oil passages and some of them may be present in the continuously variable transaxle assembly.



HINT:
·

Lock-up control will not operate when the CVT fluid temperature is 40°C (104°F) or less and the vehicle speed is 60 km/h (37 mph) or less, or when the CVT fluid temperature is 5°C (41°F) or less.

·

Lock-up control will not operate when the engine coolant temperature is 30°C (86°F) or less.

·

The lock-up off vehicle speed may vary depending on the electrical load, air conditioning and brake operations.



a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed, SPD (NT) and Lock Up.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
SPD (NT)
Lock Up
50003 234 9,390,417

e.

Check the Data List while driving.

Result:
Result Proceed to
When the lock-up is on, the turbine speed is lower than the engine speed. A
When the lock-up is off, the turbine speed is equal to the engine speed.
When the lock-up is on, the turbine speed is equal to the engine speed. B
When the lock-up is off, the turbine speed is lower than the engine speed.




A

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

B

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.REPLACE TORQUE CONVERTER ASSEMBLY
5.REPLACE TORQUE CONVERTER ASSEMBLY

Result:
Proceed to
NEXT



NEXT