The ECM controls the secondary oil pressure calibration based on the secondary oil pressure signal detected by the oil pressure sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0841 | Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The requested oil pressure value is 0.5 MPa or less. 2.
The oil pressure sensor output value is 3.0 MPa or higher. 3.
3 seconds 4.
2 trip detection logic |
·
Oil pressure sensor ·
Continuously variable transaxle assembly ·
ECM |
Comes on | DTC stored |
| P2829 | Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS) | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The requested oil pressure value is 0.5 MPa or less. 2.
The oil pressure sensor output value is 3.0 MPa or higher. 3.
3 seconds 4.
2 trip detection logic 1.
Shift lever in D, and driving at speed of 8 km/h (5 mph) or less. 2.
The ratio of the rotation speeds of the primary pulley (NIN) and secondary pulley (NOUT) exceeds the threshold. 3.
0.2 second 4.
2 trip detection logic |
·
Oil pressure sensor ·
Continuously variable transaxle assembly ·
ECM |
Comes on | DTC stored |
The ECM checks for belt clamping high-pressure or low-pressure errors. When a mechanical malfunction is detected at shift solenoid valve SLS and at the oil pressure sensor, the ECM detects the problem, illuminates the MIL and stores the DTC.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Proceed to |
|---|
| Only P0841 and/or P2829 is output |
| P0841 and/or P2829 and other DTCs are output |
If any other DTCs besides P0841 or P2829 are output, perform troubleshooting for those DTCs first.
Only P0841 and/or P2829 is output
P0841 and/or P2829 and other DTCs are output
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| A/T Oil Pressure |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Pressure | Secondary oil pressure value | min.: -64 MPa
max.: 63.998 MPa |
Secondary oil pressure inspection
3ZR-FAE:
·
D position stall speed test: 3.3 to 4.6 MPa ·
R position stall speed test: 3.0 to 3.7 MPa 3ZR-FE:
·
D position stall speed test: 3.2 to 4.5 MPa ·
R position stall speed test: 3.0 to 3.5 MPa |
- |
In accordance with the display on the GTS, read the Data List.
| Proceed to |
|---|
| Data displayed is not as specified under Normal Condition |
| Data displayed is as specified under Normal Condition |
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition
Replace the oil pressure sensor.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform reset memory, deceleration sensor zero point calibration and CVT oil pressure calibration.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Proceed to |
|---|
| P0841 and/or P2829 is output |
| DTC is not output |
P0841 and/or P2829 is output
DTC is not output
Replace the ECM.
for 3ZR-FAE:
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE:
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform reset memory, deceleration sensor zero point calibration and CVT oil pressure calibration.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Proceed to |
|---|
| P0841 and/or P2829 is output |
| DTC is not output |
P0841 and/or P2829 is output
DTC is not output
Replace the continuously variable transaxle assembly.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT