Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2012.12–2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1589  Acceleration Sensor Learning Value  


DESCRIPTION

The ECM stores DTC P1589 if the ECM or other components that require the yaw rate and acceleration sensor (airbag sensor assembly)*1 or deceleration sensor*2 to be calibrated (deceleration sensor zero point calibration) are replaced and calibration is terminated or the vehicle is driven before calibration is complete.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1589 Acceleration Sensor Learning Value Condition 1:
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle speed is 2 km/h (1.2 mph) or more.

2.

Deceleration sensor zero point calibration has not been completed.

3.

-

4.

1 trip detection logic


Condition 2:
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Deceleration sensor zero point calibration is performed.

2.

The learned values of the deceleration sensor zero point calibration are abnormal (out of normal range).

3.

-

4.

1 trip detection logic


Condition 1:

Deceleration sensor zero point calibration has not been performed


Condition 2:
·

Vehicle was not stabilized during the deceleration sensor zero point calibration

·

Yaw rate and acceleration sensor (Airbag sensor assembly)*1

·

Deceleration sensor*2

·

ECM


- DTC stored

*1: w/ VSC

*2: w/o VSC

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.PERFORM INITIALIZATION (DECELERATION SENSOR ZERO POINT CALIBRATION)
NOTICE:
·

If the CVT oil pressure calibration is performed before the deceleration sensor zero point calibration, DTC P1589 is stored. In this case, perform the steps below to return the system to normal.

·

Always perform zero point calibration with the vehicle on level ground (Inclination: 0 +/-0.25°).

·

Do not shake or vibrate the vehicle during zero point calibration.



a.

Turn the ignition switch off.


b.

Move the shift lever to P and apply the parking brake.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.

Powertrain > Engine and ECT > Utility
Tester Display
Reset Memory
50005 234 176

f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Deceleration Sensor Zero Point Calibration.

Powertrain > Engine and ECT > Utility
Tester Display
Deceleration Sensor Zero Point Calibration
50005 234 2123
HINT:
·

When "Complete" is displayed on the screen, the deceleration sensor zero point calibration is completed.

·

If "Error" is displayed on the screen and DTC P1589 is output (confirm the DTC detection conditions), the yaw rate and acceleration sensor (airbag sensor assembly)*1 or deceleration sensor*2 circuit may have a malfunction.

·

Shaking or vibrating the vehicle during zero point calibration may cancel calibration. If "Error" is displayed on the screen and DTC P1589 is not output, perform calibration again.

*1: w/ VSC

*2: w/o VSC




Result:
Result Proceed to
Deceleration sensor zero point calibration is completed normally A
DTC P1589 is output (w/ VSC) B
DTC P1589 is output (w/o VSC) C




A

2.PERFORM INITIALIZATION (CVT OIL PRESSURE CALIBRATION)

B

3.CHECK YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

C

7.CHECK DECELERATION SENSOR
2.PERFORM INITIALIZATION (CVT OIL PRESSURE CALIBRATION)
NOTICE:

Do not initialize the learned values by performing reset memory.


a.

Turn the ignition switch off and wait at least 30 seconds.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait at least 2 seconds.

NOTICE:

Do not start the engine.


HINT:

CVT oil pressure calibration is performed with the ignition switch ON (engine stopped). However, the calibration cannot be performed under the following conditions:

·

Oil pressure sensor value is 0.065 MPa (0.663 kgf/cm2, 9.43 psi) or higher.

·

CVT oil temperature is -5°C (23°F) or less or 100°C (212°F) or higher.




d.

Turn the GTS on.


e.

Start the engine and wait at least 5 seconds.

NOTICE:
·

Start the engine with the shift lever in P.

·

After starting the engine, do not operate the accelerator pedal.




f.

Enter the following menus: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration.

Powertrain > Engine and ECT > Utility
Tester Display
CVT Oil Pressure Calibration
50005 234 2122
HINT:
·

During CVT oil pressure calibration, the engine idle speed will increase.

·

When "Complete" is displayed on the screen, the CVT oil pressure calibration is completed.

·

The learned values cannot be cleared by only disconnecting and reconnecting the cable to the negative (-) battery terminal.




g.

Check that no DTC is stored.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

3.CHECK YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)
a.

Check the yaw rate and acceleration sensor (airbag sensor assembly) for any inclination, bracket deformation or installation clearance.

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is installed correctly.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (G SENSOR)

NG

SECURELY INSTALL OR REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

4.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of deceleration sensor min.: 0 V
max.: 79.998 V
Displays converted voltage of deceleration sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

e.

In accordance with the display on the GTS, read the Data List.

Result:
Proceed to
Data displayed is as specified under Normal Condition
Data displayed is not as specified under Normal Condition




Data displayed is as specified under Normal Condition

5.REPLACE ECM

Data displayed is not as specified under Normal Condition

6.REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)
a.

Replace the yaw rate and acceleration sensor (airbag sensor assembly).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DECELERATION SENSOR
a.

Check the deceleration sensor for any inclination, bracket deformation or installation clearance.

OK:

The deceleration sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (G SENSOR)

NG

8.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of deceleration sensor min.: 0 V
max.: 79.998 V
Displays converted voltage of deceleration sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

e.

In accordance with the display on the GTS, read the Data List.

Result:
Proceed to
Data displayed is as specified under Normal Condition
Data displayed is not as specified under Normal Condition




Data displayed is as specified under Normal Condition

5.REPLACE ECM

Data displayed is not as specified under Normal Condition

9.REPLACE DECELERATION SENSOR
9.REPLACE DECELERATION SENSOR

NEXT